Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Neets Touch Panel 10"
Summary of Contents for Neets Touch Panel 10"
-
Page 1: Installation Guide
Installation guide Neets Touch Panel 10”... - Page 2 Thank you! Thank you for including the Neets Touch Panel as part of the user interface strategy for your customer.
-
Page 3: Specifications
Specifications Physical Dimensions: Touch Screen: H: 169 mm 5-point capacitive touch screen W: 246 mm Scratch resistant glass-on-glass touch screen D: 41,4 mm Display: In wall: 25,4 mm 10 IPS Display, On wall: 16,5 mm Resolution: 1280x800 pixels Shipping dimensions: Brightness: 350 nits (cd/m2) 59 mm x 291 mm x 216 mm (HxWxD) Sensors:... -
Page 4: What's In The Box
What’s in the box Wall mount bracket 10” Touch Panel Cloth... - Page 5 4 x Screws Ejector pin for menu settings USB OTG adapter (for application 4 x Wall plugs and firmware upgrade)
- Page 6 Front Ambient light Proximity sensor sensor 169 mm 246 mm...
- Page 7 Back Firmware upgrade Magnet LAN/POE Magnet Magnets Factory Reset Settings button...
- Page 8 Steps Touch Panel position Mount Touch Panel on bracket Bracket details Connect PoE injector Mounting the bracket First start up Connect LAN/PoE...
- Page 9 Touch Panel position The Touch Panel is designed to wall mount in landscape orientation, and depending on how tall the users are we 165 cm / 65 in. recommend locating the center of the touch panel between 145 cm. – 165 cm. (57”...
-
Page 10: Bracket Details
Bracket details The Touch Panel is designed to mount into a 1- or 2-gang back box in EU, US or DK standards or can be mounted without a back box. When using EU and US standards use the threads that are already in the back box and secure the bracket with fitting screws. - Page 11 The numbers on the bracket refers to the back box it is intended for. EU 1-gang back box EU 2-gang back box US 1-gang back box US 2-gang back box Holes for mounting directly into the wall Alignment holes – do not use these for screws...
-
Page 12: Mounting The Bracket
Mounting the bracket When mounting the Touch Panel into a EU/US back box follow the steps below. In case you are not mounting on a EU/US back box skip step 1. Before you start make sure the wall is even to prevent distorting the bracket. Mount the bracket onto the back box Remove the bracket again using the screws and screw holes for the... - Page 14 Connect LAN / PoE Connect the PoE cable from the wall to the Touch Panel.
- Page 15 Mount Touch Panel on bracket Place the Touch Panel onto the bracket. Make sure it is placed correctly and the alignment holes are free to fix the Touch Panel to all four magnets.
- Page 16 Connect PoE injector Power outlet LAN switch...
-
Page 17: First Start-Up
The Touch Panel will automatically power on when power is applied. Wait for the unit to start up and follow the instructions. For a complete configuration guide please go to: www.neets.dk/products/touch- panels/ You will find the instructions for firmware updates the same place. -
Page 18: Removing The Touch Panel
Removing the Touch Panel Using two hands grasp on each side of the Touch Panel and pull straight out from the wall. - Page 19 B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide dangerous voltage or other hazards. Contact your local Neets reseller or distributor. reasonable protection against harmful interference in a residential installation. This equipment...
- Page 20 Learn more at neets.dk Visit our website neets.dk for additional information about the product and the latest firmware. Neets A/S | Langballe 4, 8700 Horsens, Denmark | +45 75 666 099 | sales@neets.dk | www.neets.dk...