Miele TWI1 Quick Start Manual

Initial commissioning Operation
寿
Before using the tumble dryer for
the first time, ensure that it is correctly
installed and connected.
If the tumble dryer has not been trans-
ported as described in "Installation and
connection" then it must be left to stand
for at least 1 hour before it is connected
to the electricity supply. Otherwise the
heat pump can be damaged.
It is essential to read the operating instruc- 1 Control field 6 Optical interface
tions. The control field consists of a display and for service technicians.
various sensor buttons. 7 Sensor buttons for extras
2 Display You can supplement the drying program
Different values are displayed and/or with extra options.
selected on the display: 8 Sensor button 
3 Sensor buttons  You can use the  sensor button to call
The values in the display can be changed up an energy consumption forecast for
with the  sensor buttons. the selected drying program.
4 OK sensor button 9 Sensor button 
Confirm the selected values with the OK The sensor button  starts the delay
sensor button. start function.
5 Perfect Dry indicator  10 Start/Stop sensor button
With programs with a selectable drying Touching the Start/Stop sensor button
level, the Perfect Dry system calculates starts the selected program or cancels a
the residual moisture present in the laun- program that has already been started.
dry to ensure a precise drying result.
The display flashes at the beginning of
the program and lights up towards the
end of the program.
Energy saving tips
To avoid unnecessarily long drying times – Load according to the optimum
and high consumption of energy: amount of laundry recommended for
– Make sure your laundry is spun at the the program being used. This will mean
maximum spin speed before drying. that the energy consumption for the
amount of laundry is at its most eco-
nomical.
– Clean the lint filters after every drying
cycle.
Drying
1. Notes on correct laundry care
寿
Remove foreign objects like detergent dispensing
Switching on the tumble dryer
ĺ
devices from the laundry.
Turn the program selector to a program.
They can melt and damage the dryer and the laundry.
The welcome tone will sound and the wel-
ĺ
come screen will light up. The display will Sort the laundry according to the type of fiber and
now guide you through the initial commis- weave, size, garment care label symbol, and the drying
sioning, which is divided into several steps. ĺ level required.
For further information please refer to the Untangle the laundry.
ĺ
separate operating instructions supplied. Check seams and stitching to ensure that padding and
linings are intact.
ĺ
Fasten duvet covers and pillow cases to prevent small
items from being rolled up inside them.
ĺ
ĺ Fasten hooks and eyes.
Tie together textile belts and apron ties.
ĺ
11 Program selector Sew in or remove underwiring from bras.
For selecting programs and for switch-
ing off the machine. The tumble dryer is
switched on when you select a program,
and switched off by turning the program
selector to the  position.
Operating the sensor buttons
The sensor buttons react to fingertip con-
2. Selecting a program
tact. Selection is possible as long as the
ĺ
respective sensor button is illuminated. Turn the program selector to a program.
If a sensor button is brightly lit, The interior drum lighting will come on.
this means: currently selected 1 Condensed water container
If a sensor button is dimly lit, Program selection – empty after every drying program
this means: selection possible There are three possible ways to select a program: 2 Door
3 Control panel
1. Selecting the standard programs with the program Access panel for the heat exchanger and plinth filter
4
selector dial – do not open during drying
ĺ
Turn the program selector to the required program. 5 Cool air intake grille
The selected program will be shown in the display. This – do not obstruct with a laundry basket or other objects
will then be replaced by the standard display.
2. Selecting more programs by setting the program
– Make sure the room temperature is not selector to the "More programs/" position and the
too high. display.
ĺ
If there are other heat producing appli- Turn the program selector to the More programs/ 3. Selecting the programs via the MobileControl 
ances in the room in which the tumble position. program selector position and the Miele@mobile app
ĺ
dryer is located, make sure the room The following will appear in the display: Time Dry Turn the program selector to the MobileControl  position.
ĺ ĺ
is well-ventilated and switch the other Touch the  sensor buttons until the program you Follow the instructions in the display.
ĺ
appliances off, if possible. want appears in the display. Touch the "Start/Stop" sensor button.
ĺ
Confirm the program with the OK sensor button. The dryer can now be operated via a mobile device together
with the Miele@mobile app.
3. Loading the tumble dryer 6. Program end – removing the
Selecting an extra option
ĺ ĺ
laundry
ĺ Open the door. Touch the sensor button for the desired
Unfold the laundry and load extra. It then lights up brightly. The program is finished when End/
loosely into the drum. Freshen up Anti-crease or End appears. The Start/Stop
寿 For removing or reducing odors in clean button light goes out.
Do not overload the drum.
(dry or damp) clothing. – To save energy, 10 minutes after the end
Overloading can cause unnec-
Gentle of the program the Start/Stop sensor but-
essary wear and tear to the laun-
the  symbol on the care label, e.g. acrylic Low temperature for delicate fabrics with ton will begin to flash slowly and the dis-
dry, give a disappointing drying
play will go out.
result and cause more creasing.
garments. – The tumble dryer switches off automati-
寿 If you are not using a fra- Anti-crease cally.
grance capsule: The tab must be Helps to prevent creasing if the laundry is
寿
Do not open the door before the end
pushed down completely (see not removed immediately after the end of a
of the program.
arrow). program. ĺ
Buzzer Open the door.
寿
When closing the door, make A buzzer sounds to let you know the pro-
sure that laundry does not get
gram has finished.
trapped in the door opening.
ĺ
Shut the door with a gentle  EcoFeedback
swing. You can use the  sensor button to call
up an energy consumption forecast for the
selected drying program.
ĺ ĺ
Touch the  sensor button. Remove the laundry.
The estimated energy consumption levels 寿
Check that all items have been
4. Selecting program settings
will be displayed as a bar chart.
removed from the drum. If items are left
in the dryer, they could be damaged by
Programs with drying levels  Delay start/SmartStart
overdrying when the dryer is next used.
Normal, Wrinkle-free, Delicates, Smoothing, Dress Shirts, Delay start
Express, Denim, Outdoor, Sportswear, Steam Care, Table With the delay start function, you can delay The inside of the drum lights up so that
Linen/Drapes, Bed linen the start of the program. The start of the you don't forget any items of laundry
The pre-set drying level can be changed if required. program can be delayed from 15 minutes when you empty it.
ĺ
Touch the  or  sensor buttons to change the dry- up to a maximum of 24 hours. The drum lighting switches off
ing level. SmartStart automatically (energy saving).
ĺ
With the SmartStart function you can define Turn the program selector to .
ĺ
Time-controlled and other programs a time period during which your dryer will Clean the lint filters.
ĺ
Time Dry, Cold Air, Basket be started automatically by a signal, for Close the drum door.
ĺ
You can change the duration in ten-minute increments. instance to make use of cheaper electric- Empty the condensed water container.
ĺ
Touch the  or  sensor buttons to change the dura- ity rates.
tion.
5. Starting a program
Woollens/Silks, Pillows, Proofing
ĺ
The drying result is preset by the dryer and cannot be Touch the flashing Start/Stop sensor but-
altered. ton.
The Start/Stop sensor button will light up
and
Drying will appear in the display.
Changing the program Fragrance capsule
Emptying the condensed water
You cannot change to another program Tip: Using a fragrance capsule will add a
container once a program has started (this prevents pleasant fragrance to your laundry.
unintentional alterations). If you move the 寿
Before using a fragrance capsule,
program selector, Cannot be changed will
 please read "IMPORTANT SAFETY
Empty the condensed water container
light up in the display until you move the
INSTRUCTIONS – Using a fragrance
after every drying program.
program selector back to the original pro-
capsule (optional accessory)" and
 Empty container See . gram. "Fragrance capsule" in the operating
will light up in the display if the maximum Exception: The dryer is switched off by instructions.
level of the condensed water container is turning the program selector to the  posi-
reached. tion. Inserting a fragrance capsule
To turn the message off: Open and close You will need to cancel the current program 1. 2.
the door while the dryer is switched on. before you can select a new one.
ĺ
Remove the
condensed water ĺ Canceling a program
container. Touch the Start/Stop sensor button.
Cancel program will light up in the display.
ĺ
Confirm with the OK sensor button.
As soon as Program canceled lights up:
ĺ 3. 4.
Turn the program selector to .
ĺ
To prevent water running out, keep it in a
horizontal position when carrying it. Hold The current program can also be
it at the front and towards the back. canceled in this way
ĺ ĺ
Empty the Turn the program selector to .
ĺ
condensed water Select a program.
ĺ
container. Touch the Start/Stop sensor button.
ĺ Markers  and  must line up with
Replace the con- The drying cycle begins.
densed water
one another.
container in the Adding or removing laundry
5. 6.
dryer.
寿
Bear in mind that hot steam can
寿
Do not drink condensed water. It can escape after the door is opened.
ĺ
cause health problems in people and ani-
ĺ Pull open the door.
mals.
Add or remove items.
ĺ
Close the door.
ĺ
Touch the Start/Stop sensor button.
ĺ
The program starts. Turn the outer ring clockwise a little.
Program duration
Altering the program sequence can cause
the program duration shown in the time dis-
play to be adjusted.
Before drying
ĺ
Turn the outer
ring clockwise.
The further you open the capsule, the
more intense the fragrance.
After drying
To avoid the fragrance escaping need-
lessly: ĺ
Turn the outer
ring counter-
clockwise until
marker  is in
position .
If you want to dry laundry occasionally
without adding fragrance: Remove the
fragrance capsule and store it in its orig-
inal packaging until you want to use it
again. See the following section.
Before cleaning the lint filters
ĺ
Remove the
fragrance
capsule
(reverse points
3 and 4) and
store it in its
original packa-
ging.
寿 Never lay the fragrance capsule
down on any surface as the fragrance
will spill out.