Chamberlain KLIK2U Manual

Thank you for your purchase of the Universal Wireless Keypad.
PLEASE DO NOT RETURN TO THE RETAIL STORE. If for any reason you have questions or need
help with troubleshooting please call: 1-800-442-1255.
Read instructions thoroughly BEFORE beginning. If using this product with
residential door openers, this product must be used only with door openers
STOP
manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors
are always located on or near the bottom of the door track.
GETTING STARTED
Locate the Learn button on the garage door opener. NOTE: Your garage door opener may look
different.
Compatible with Chamberlain, Sears Craftsman, LiftMaster, Master Mechanic, Do It, Genie
Intellicode**, Overhead Door, Stanley, Wayne Dalton or Linear garage door openers with Smart/
Learn button.
** For Genie Intellicode and DIP switch programming instructions, visit
http://www.chamberlain.com/CatalogResourcesV3/en-us/shared/files/
tucmanuals/114A5072.pdf
PROGRAMMING
1
Select and write a 4-digit PIN:
__ __ __ __
2
Determine your opener ID using the list below.
ID Garage door opener brand and manufacturing dates
1 Linear garage door openers manufactured from 1997 to present.
2 Chamberlain, Sears Craftsman, LiftMaster, Master Mechanic and Do It garage door
openers manufactured from 1997 to 2004 [Orange/Red Button].
3 Chamberlain, Sears Craftsman, LiftMaster, Master Mechanic and Do It garage door
openers manufactured from 2005 to present [Purple Button].
4 Chamberlain, Sears Craftsman, LiftMaster, Master Mechanic and Do It garage door
openers manufactured from 1993 to 1996 [Green Button].
5 Genie Intellicode and Overhead Door garage door openers manufactured from
2005 to present (315 MHz).
6 Genie Intellicode and Overhead Door garage door openers manufactured from
1995 to present (390 MHz).
7 Stanley garage door openers manufactured in 1998 to present.
8 Chamberlain, Sears Craftsman, and LiftMaster garage door openers manufactured
2011 to present [Yellow Button].
9 Wayne Dalton garage door openers manufactured in 1999 to present.
(Write opener ID here: __ __ )
INSTALLATION
Install out of reach of small children at a minimum height of 5 feet (1.5 m) above floors,
landings, steps or any other adjacent walking surface, and away from ALL moving parts of door.
Secure keypad to a smooth surface. Mount the keypad out of the path of the moving garage door,
but within sight of it (4" [10 cm] clearance is needed for the cover).
1. Remove cover.
2. Remove battery cover to
expose mounting holes.
3. Remove battery and mount
keypad using screws provided.
4. Reassemble.
www.chamberlain.com • 1-800-442-1255
Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genie and Intellicode are Trademarks of GMI
Holdings, Inc. Overhead Door is a trademark of Overhead Door Corporation. Linear is a Trademark of Linear Corporation. Master
Mechanic is a Trademark of TruServ. Sears is a Trademark of Sears & Roebuck. Stanley is a Trademark of The Stanley Works. Wayne
Dalton is a trademark of Wayne Dalton Corporation. Do It is a trademark of Do It Best Corporation.
OR OR
Learn
Learn
LED
LED
Green or
Red/Orange
Purple
1
3
2
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
• Install keypad within sight of garage door, out of reach of small children at a minimum
height of 5 feet (1.5 m) above floors, landings, steps or any other adjacent walking surface,
and away from ALL moving parts of door.
• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate,
or play with remote controls.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are
no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to
cross path of moving gate or door.
WARNING: This product can expose you to chemicals including lead, which are known
to the State of California to cause cancer or birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov
Learn
LED
Para Manual en Español ir a:
Yellow
http://www.chamberlain.com/CatalogResourcesV3/en-us/shared/files/
tucmanuals/114A3484SP.pdf
3
Press and hold the * and # buttons until keypad stops flashing.
4
Enter PIN from step 1, press #.
5
Enter ID from step 2, press #.
6
Press and release the Smart/Learn button on the garage door
opener.
7
Enter your 4 digit PIN and press the 0 key.
NOTE: For Genie and Overhead Door units, press the 0 key twice.
8
To test and use, wait until lights turn off, enter your PIN
and press the 0 key.
If opener does not function, repeat programming.
CHANGING YOUR 4-DIGIT PIN
Enter existing PIN, press *, enter new PIN and press *.
To test and use, enter your new PIN and press the 0 key. If changing PIN does not work, follow
programming steps above.
BATTERY
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
Replace the 9-Volt battery when
keypad light becomes dim or does
not light up. Slide cover up, remove
battery cover, and replace battery.
Re-programming may be necessary.
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are
prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards for Home or office use. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
UNIVERSAL WIRELESS KEYPAD
MODELS KLIK2U, KLIK2U-P2, KLIK2C AND KLIK2C-P2
9V Battery