Page 1 2008 Saturn AURA Owner Manual Seats and Restraint Systems ... 1-1 Front Seats ... 1-2 Rear Seats ... 1-9 Safety Belts ... 1-11 Child Restraints ... 1-31 Airbag System ... 1-56 Restraint System Check ... 1-72 Features and Controls ... 2-1 Keys ...
Page 2: Canadian Owners
GENERAL MOTORS and GM are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. Saturn reserves the right to make changes after that time without further notice. This manual describes features that may or may not be on your speciﬁc vehicle.
Page 3: Using This Manual
Using this Manual Read this owner manual from beginning to end to learn about the vehicle’s features and controls. Pictures and words work together to explain things. Index To quickly locate information about the vehicle use the Index in the back of the manual. It is an alphabetical list of what is in the manual and the page number where it can be found.
Page 4: Vehicle Symbols
Vehicle Damage Warnings Notices are also used in this manual. Notice: These mean there is something that could damage your vehicle. A notice tells about something that can damage the vehicle. Many times, this damage would not be covered by the vehicle’s warranty, and it could be costly. The notice tells what to do to help avoid the damage.
Page 5: Table Of Contents
Section 1 Front Seats ...1-2 Manual Seats ...1-2 Power Seats ...1-3 Manual Lumbar ...1-3 Heated Seats ...1-4 Reclining Seatbacks ...1-4 Head Restraints ...1-7 Power Lift Seat ...1-8 Rear Seats ...1-9 Split Folding Rear Seat ...1-9 Safety Belts ...1-11 Safety Belts: They Are for Everyone ...1-11 How to Wear Safety Belts Properly ...1-16 Lap-Shoulder Belt ...1-25 Safety Belt Use During Pregnancy ...1-30...
Page 6: Front Seats
Front Seats Manual Seats CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Page 7: Power Seats
Power Seats In vehicles with power seats, the controls used to operate them are located on the outboard side of the seat. To adjust the seat: • Move the seat forward or rearward by sliding the control forward or rearward. •...
Page 8 Heated Seats Your vehicle may have heated front seats. The buttons are located on the outboard side of the driver’s and front passenger’s seats. Press the top of the switch to turn the feature on. The seat will heat to the high setting. The indicator light above the switch will be lit next to the number 2.
Page 9 On seats with manual reclining seatbacks, the lever used to operate them is located on the outboard side of the seat. To recline the seatback: 1. Lift the recline lever. 2. Move the seatback to the desired position, then release the lever to lock the seatback in place. 3.
Page 10: Power Reclining Seatbacks
Power Reclining Seatbacks If the seats have power reclining seatbacks, the control used to recline them is located on the outboard side of the seat behind the power seat control. • To recline the seatback, tilt the top of the control rearward.
Page 11: Head Restraints
Do not have a seatback reclined if your vehicle is moving. Head Restraints Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant’s head. This position reduces the chance of a neck injury in a crash.
Page 12: Power Lift Seat
Pull the restraint up to raise it. To lower the head restraint, press the button, located on the top of the seatback, and push the restraint down. The rear seat head rests are also adjustable. Power Lift Seat To adjust a power lift seat, press the top or bottom of the power lift seat switch to raise or lower the seat.
Page 13: Rear Seats
Rear Seats Split Folding Rear Seat With this feature, you can fold either side of the seatback down for more cargo space. Make sure the front seat is not reclined. If it is, the rear seatback will not fold down all the way. Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts.
Page 14 To raise the rear seatback pull the seatback up and make sure it latches. Push and pull on the seatback to be sure it is locked in position. Make sure that the safety belts are properly stowed over the seatback in all three positions.
Page 15: Safety Belts
Safety Belts Safety Belts: They Are for Everyone This section of the manual describes how to use safety belts properly. It also describes some things not to do with safety belts. CAUTION: Do not let anyone ride where he or she cannot wear a safety belt properly.
Page 16: Why Safety Belts Work
In most states and in all Canadian provinces, the law requires wearing safety belts. Here is why: You never know if you will be in a crash. If you do have a crash, you do not know if it will be a serious one. A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive.
Page 17 Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. 1-13...
Page 18 The person keeps going until stopped by something. or the instrument panel... In a real vehicle, it could be the windshield... 1-14...
Page 19: Questions And Answers About Safety Belts
or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. Questions and Answers About Safety Belts Will I be trapped in the vehicle after a crash if I...
Page 20: How To Wear Safety Belts Properly
If I am a good driver, and I never drive far from home, why should I wear safety belts? You may be an excellent driver, but if you are in a crash — even one that is not your fault — you and your passenger(s) can be hurt.
Page 21 Sit up straight and always keep your feet on the ﬂoor in front of you. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt.
Page 22 What is wrong with this? The shoulder belt is too loose. It will not give as much protection this way. 1-18 CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Page 23 What is wrong with this? The lap belt is too loose. It will not give nearly as much protection this way. CAUTION: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
Page 24 What is wrong with this? The belt is buckled in the wrong buckle. 1-20 CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones.
Page 25 What is wrong with this? The belt is over an armrest. CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt.
Page 26 What is wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. 1-22 CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 27 What is wrong with this? The belt is behind the body. CAUTION: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury.
Page 28 What is wrong with this? The belt is twisted across the body. 1-24 CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to ﬁx it.
Page 29: Lap-Shoulder Belt
Lap-Shoulder Belt All seating positions in your vehicle have a lap-shoulder belt. Here is how to wear a lap-shoulder belt properly. 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. To see how, see “Seats” in the Index. 2.
Page 30 5. To make the lap part tight, pull up on the shoulder belt. It may be necessary to pull stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants. 1-26 To unlatch the belt, push the button on the buckle. The belt should go back out of the way.
Page 31 Shoulder Belt Height Adjuster Your vehicle has a shoulder belt height adjuster for the driver and right front passenger position. Adjust the height so that the shoulder portion of the belt is centered on your shoulder. The belt should be away from your face and neck, but not falling off your shoulder.
Page 32: Rear Safety Belt Comfort Guides
Rear Safety Belt Comfort Guides Rear shoulder belt comfort guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults. When installed on a shoulder belt, the comfort guide positions the belt away from the neck and head.
Page 33 3. Be sure that the belt is not twisted and it lies ﬂat. The elastic cord must be under the belt and the guide on top. CAUTION: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously CAUTION: (Continued) CAUTION: (Continued)
Page 34: Safety Belt Use During Pregnancy
To remove and store the comfort guide, squeeze the belt edges together so that you can take them out of the guide. Pull the guide upward to expose its storage clip, and then slide the guide onto the clip. Turn the guide and clip inward and slide them in between the seatback and the interior body, leaving only the loop of the elastic cord exposed.
Page 35: Child Restraints
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. The manufacturer’s instructions that come with the booster seat state the weight and height limitations for that booster. Use a booster seat with a lap-shoulder belt until the child passes the below ﬁt test: •...
Page 36 What is the proper way to wear safety belts? An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should ﬁt snugly below the hips, just touching the top of the thighs.
Page 37 CAUTION: Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt. The child could move too far forward increasing the chance of head and neck injury.
Page 38: Infants And Young Children
Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
Page 39 CAUTION: Never do this. Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a CAUTION: (Continued) CAUTION: (Continued) rear-facing child restraint in a rear seat.
Page 40 What are the different types of add-on child restraints? Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
Page 41: Child Restraint Systems
CAUTION: A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child’s abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure.
Page 42 A booster seat (C-D) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. A booster seat can also help a child to see out the window. 1-38 Securing an Add-On Child Restraint in the Vehicle CAUTION: A child can be seriously injured or killed in a crash if the child restraint is not properly...
Page 43: Where To Put The Restraint
To help reduce the chance of injury, the child restraint must be secured in the vehicle. Child restraint systems must be secured in vehicle seats by lap belts or the lap belt portion of a lap-shoulder belt, or by the LATCH system.
Page 44 A label on your sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inﬂates.
Page 45 When securing a child restraint in a rear seating position, study the instructions that came with your child restraint to make sure it is compatible with this vehicle. Wherever you install a child restraint, be sure to secure the child restraint properly. Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure people in the vehicle.
Page 46: Lower Anchors And Tethers For Children (Latch)
A. Child restraint using LATCH B. Child restraint or occupant using safety belt C. Child restraint using safety belt or LATCH or occupant using safety belt A. Child restraint or occupant using safety belt A. Child restraint or occupant using safety belt B.
Page 47: Top Tether Anchor
Lower Anchors Lower anchors (A) are metal bars built into the vehicle. There are two lower anchors for each LATCH seating position that will accommodate a child restraint with lower attachments (B). Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle.
Page 48 Some child restraints with top tethers are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached.
Page 49: Securing A Child Restraint Designed For The Latch System
Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be attached, or if the instructions that come with the child restraint say that the top tether must be attached.
Page 50 CAUTION: Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Buckle any unused safety belts behind the child restraint so children cannot reach them. Pull the shoulder belt all the way out of the retractor to set the lock, if your vehicle has one, after the child restraint has been installed.
Page 51 A. Passenger Side Rear Seat Lower Anchors B. Center Rear Seat Lower Anchors C. Driver Side Rear Seat Lower Anchors Make sure to attach the child restraint at the proper anchor location. This system is designed to make installation of child restraints easier.
Page 52 2. If the child restraint manufacturer recommends that the top tether be attached, attach and tighten the top tether to the top tether anchor, if equipped. Refer to the child restraint instructions and the following steps: 2.1. Find the top tether anchor. 2.2.
Page 53: Securing A Child Restraint In A Rear Seat Position
If the position you are using has an adjustable headrest or head restraint and you are using a dual tether route the tether under the headrest or head restraint and in between the headrest or head restraint posts. See Head Restraints on page 1-7.
Page 54 If the child restraint does not have the LATCH system, you will be using the safety belt to secure the child restraint in this position. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say.
Page 55 4. Pull the rest of the shoulder belt all the way out of 5. To tighten the belt, push down on the child restraint, the retractor to set the lock. pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
Page 56: Securing A Child Restraint In The Right Front Seat Position
6. If the child restraint has a top tether, follow the child restraint manufacturer’s instructions regarding the use of the top tether. See Lower Anchors and Tethers for Children (LATCH) on page 1-42 for more information. 7. Push and pull the child restraint in different directions to be sure it is secure.
Page 57 CAUTION: (Continued) Secure rear-facing child restraints in a rear seat, even if the airbag is off. If you secure a forward-facing child restraint in the right front seat, always move the front passenger seat as far back as it will go. It is better to secure the child restraint in a rear seat.
Page 58 4. Push the latch plate into the buckle until it clicks. 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if necessary.
Page 59 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. If you are using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 60: Airbag System
Airbag System Your vehicle has the following airbags: • A frontal airbag for the driver. • A frontal airbag for the right front passenger. • A seat-mounted side impact airbag for the driver. • A seat-mounted side impact airbag for the right front passenger.
Page 61 CAUTION: Frontal airbags are designed to deploy in moderate to severe frontal and near frontal crashes. They are not designed to inﬂate in rollover, rear crashes, or in many side crashes. Seat-mounted side impact airbags and roof-rail airbags are designed to inﬂate in moderate to severe crashes where something hits the side of your vehicle.
Page 62: Where Are The Airbags
CAUTION: Airbags plus lap-shoulder belts offer the best protection for adults, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them. Young children and infants need the protection that a child restraint system can provide.
Page 63 The right front passenger’s frontal airbag is in the instrument panel on the passenger’s side. Driver Side shown, Passenger Side similar The seat-mounted side impact airbags for the driver and right front passenger are in the side of the seatbacks closest to the door.
Page 64 Driver Side shown, Passenger Side similar The roof-rail airbags for the driver, right front passenger, and second row outboard passengers are in the ceiling above the side windows. 1-60 CAUTION: If something is between an occupant and an airbag, the airbag might not inﬂate properly or it might force the object into that person causing severe injury or even death.
Page 65: When Should An Airbag Inﬂate
When Should an Airbag Inﬂate? Frontal airbags are designed to inﬂate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver’s or right front passenger’s head and chest. However, they are only designed to inﬂate if the impact exceeds a predetermined deployment threshold.
Page 66 In addition, the vehicle has dual-stage frontal airbags. Dual-stage airbags adjust the restraint according to crash severity. The vehicle has electronic frontal sensors, which help the sensing system distinguish between a moderate frontal impact and a more severe frontal impact. For moderate frontal impacts, dual-stage airbags inﬂate at a level less than full deployment.
Page 67: What Makes An Airbag Inﬂate
What Makes an Airbag Inﬂate? In a deployment event, the sensing system sends an electrical signal triggering a release of gas from the inﬂator. Gas from the inﬂator ﬁlls the airbag causing the bag to break out of the cover and deploy. The inﬂator, the airbag, and related hardware are all part of the airbag module.
Page 68: What Will You See After An Airbag Inﬂates
What Will You See After an Airbag Inﬂates? After the frontal airbags and seat-mounted side impact airbags inﬂate, they quickly deﬂate, so quickly that some people may not even realize an airbag inﬂated. Roof-rail airbags may still be at least partially inﬂated for some time after they deploy.
Page 69: Passenger Sensing System
In many crashes severe enough to inﬂate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inﬂate only once. After an airbag inﬂates, you will need some new parts for the airbag system.
Page 70 The passenger sensing system will turn off the right front passenger’s frontal airbag and seat-mounted side impact airbag under certain conditions. The driver’s airbags are not part of the passenger sensing system. The passenger sensing system works with sensors that are part of the right front passenger’s seat.
Page 71 The passenger sensing system is designed to turn off the right front passenger’s frontal airbag and seat-mounted side impact airbag if: • The right front passenger seat is unoccupied. • The system determines that an infant is present in a rear-facing infant seat. •...
Page 72 For some children who have outgrown child restraints and for very small adults, the passenger sensing system may or may not turn off the right front passenger’s frontal airbag and seat-mounted side impact airbag, depending upon the person’s seating posture and body build. Everyone in your vehicle who has outgrown child restraints should wear a safety belt properly —...
Page 73 CAUTION: If the airbag readiness light in the instrument panel cluster ever comes on and stays on, it means that something may be wrong with the airbag system. If this ever happens, have the vehicle serviced promptly, because an adult-size person sitting in the right front passenger’s seat may not have the protection of the airbag(s).
Page 74: Servicing Your Airbag-Equipped Vehicle
Servicing Your Airbag-Equipped Vehicle Airbags affect how your vehicle should be serviced. There are parts of the airbag system in several places around your vehicle. Your dealer/retailer and the service manual have information about servicing your vehicle and the airbag system. To purchase a service manual, see Service Publications Ordering Information on page 7-16.
Page 75 In addition, your vehicle has a passenger sensing system for the right front passenger’s position, which includes sensors that are part of the passenger’s seat. The passenger sensing system may not operate properly if the original seat trim is replaced with non-GM covers, upholstery or trim, or with GM covers, upholstery or trim designed for a different vehicle.
Page 76: Restraint System Check
Restraint System Check Checking the Restraint Systems Safety Belts Now and then, check the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly. Look for any other loose or damaged safety belt system parts.
Page 77: Replacing Restraint System Parts After A Crash
Replacing Restraint System Parts After a Crash CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
Page 78 ✍ NOTES 1-74...
Page 79: Features And Controls
Section 2 Keys ...2-2 Remote Keyless Entry (RKE) System ...2-3 Remote Keyless Entry (RKE) System Operation ...2-4 Remote Vehicle Start ...2-6 Doors and Locks ...2-9 Door Locks ...2-9 Power Door Locks ...2-9 Door Ajar Reminder ...2-9 Delayed Locking ...2-10 Programmable Automatic Door Locks ...2-10 Rear Door Security Locks ...2-11 Lockout Protection ...2-12 Trunk ...2-12...
Page 80: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing...
Page 81: Remote Keyless Entry (Rke) System
Remote Keyless Entry (RKE) System If this vehicle has the Remote Keyless Entry (RKE) system, it operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Page 82: Remote Keyless Entry (Rke) System Operation
Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions will work up to 195 feet (60 m) away, however, the operating range may be less while the vehicle is running. There are other conditions which can affect the performance of the transmitter.
Page 83: Matching Transmitter(S) To Your Vehicle
(Unlock): Press to unlock the driver’s door. If pressed again within ﬁve seconds, all remaining doors unlock. The interior lamps turn on and stay on for 20 seconds or until the ignition is turned on. If enabled through the DIC, the remote unlock feedback can be programmed to have the horn chirp and/or the turn signals ﬂash when the RKE transmitter is used to unlock the vehicle’s doors.
Page 84: Remote Vehicle Start
Battery Replacement Replace the battery if the KEY FOB BATT (Battery) LOW message displays in the DIC. See “KEY FOB BATT (Battery) LOW” under DIC Warnings and Messages on page 3-47 for additional information. Notice: When replacing the battery, do not touch any of the circuitry on the transmitter.
Page 85 Do not use the remote start feature if your vehicle is low on fuel. Your vehicle may run out of fuel. If your vehicle has the remote start feature, the RKE transmitter functions will have an increased range of operation. However, the range may be less while the vehicle is running.
Page 86 To manually shut off a remote start, do any of the following. • Aim the RKE transmitter at the vehicle and press and release the remote start button. • Turn on the hazard warning ﬂashers. • Turn the ignition switch out of LOCK/OFF position and then back to LOCK/OFF.
Page 87: Doors And Locks
Doors and Locks Door Locks CAUTION: Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Page 88: Delayed Locking
Delayed Locking This feature allows the driver to delay the locking of the vehicle. It will not operate with the key in the ignition. See Lockout Protection on page 2-12. Press the driver’s power door lock switch or the Remote Keyless Entry (RKE) transmitter lock button once.
Page 89: Rear Door Security Locks
Rear Door Security Locks Your vehicle has rear door security locks, that prevent passengers from opening the rear doors from the inside. The rear door security locks are located on the inside edge of each rear door. You must open the rear doors to access them.
Page 90: Lockout Protection
Lockout Protection This feature prevents the driver’s door from being locked using the power door locks, if the key is left in the ignition and a door is open. Press the power door lock switch to lock all the doors and then unlock the driver’s door.
Page 91 Remote Trunk Release Press the button located on the driver’s door near the map pocket to open the trunk. The trunk can only be opened while the vehicle is in PARK (P). To close the trunk use the pullstrap located on the trunk lid.
Page 92: Windows
Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 93: Power Windows
Power Windows The power window switches are located on the armrest on the driver’s door. In addition, each passenger door has a switch for its own window. Express-Down Window The driver’s window has an express-down feature. This switch is labeled AUTO. Press the front all the way down and release, to lower the window all the way down automatically.
Page 94: Sun Visors
Express Window Anti-Pinch Feature If any object is in the path of the window when the express-up is active, the window stops at the obstruction and auto-reverse to a preset factory position. Weather conditions such as severe icing may also cause the window to auto-reverse.
Page 95: Theft-Deterrent Systems
Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. This vehicle has theft-deterrent features, however, they do not make it impossible to steal. Content Theft-Deterrent Your vehicle may have a content theft-deterrent alarm system. Arming the System With the ignition off, press the Remote Keyless Entry (RKE) transmitter lock button to arm the system.
Page 96: Pass-Key Iii+ Electronic Immobilizer
How the System Alarm is Activated To activate the system if it is armed: • Open the driver’s door or trunk. A ten second pre-alarm chirp will sound followed by a thirty second full alarm of horn and lights. • Open any other door.
Page 97: Pass-Key Iii+ Electronic Immobilizer Operation
® PASS-Key III+ Electronic Immobilizer Operation ® Your vehicle has PASS-Key III+ (Personalized Automotive Security System) theft-deterrent system. ® PASS-Key III+ is a passive theft-deterrent system. The system is automatically armed when the key is removed from the ignition. You do not have to manually arm or disarm the system. The security light will come on if there is a problem with arming or disarming the theft-deterrent system.
Page 98: Starting And Operating Your Vehicle
To program the new key: 1. Verify that the new key has a 2. Insert the already programmed key in the ignition and start the engine. If the engine will not start, see your dealer/retailer for service. 3. After the engine has started, turn the key to LOCK/OFF, and remove the key.
Page 99: Ignition Positions
Ignition Positions With the key in the ignition switch, you can turn it to four different positions. In order to shift out of PARK (P), ignition must be in the ON/RUN or ACC/ACCESSORY and the regular brake pedal must be applied. Notice: Using a tool to force the key from the ignition switch could cause damage or break the key.
Page 100: Retained Accessory Power (Rap)
Key In the Ignition Never leave your vehicle with the keys inside, as it is an easy target for joy riders or thieves. If you leave the key in the ignition and park your vehicle, a chime sounds, when the driver’s door is opened. Always remember to remove the key from the ignition and take it with you.
Page 101: Starting Procedure
Starting Procedure 1. With your foot off the accelerator pedal, turn the ignition key to START. When the engine starts, let go of the key. The idle speed will go down as your engine gets warm. Do not race the engine immediately after starting it.
Page 102: Adjustable Throttle And Brake Pedal
Adjustable Throttle and Brake Pedal If your vehicle has this feature, you can change the position of the throttle and brake pedals. This feature is designed for shorter drivers, since the pedals cannot move farther away from the standard position, but can move rearward for better pedal reach.
Page 103: To Use The Engine Coolant Heater
To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The engine coolant heater cord is located near the air cleaner box on the passenger side of the engine compartment. See Engine Compartment Overview on page 5-14 for more information on location.
Page 104: Automatic Transmission Operation
Automatic Transmission Operation XE Model Your automatic transmission has a shift lever located on the console between the seats. PARK (P): This position locks your front wheels. It is the best position to use when you start your engine because your vehicle cannot move easily. 2-26 CAUTION: It is dangerous to get out of the vehicle if the...
Page 105 Make sure the shift lever is fully in PARK (P) before starting the engine. Your vehicle has an automatic transmission shift lock control system. You have to apply your regular brake ﬁrst and then press the shift lever button before you can shift from PARK (P). If you cannot shift out of PARK (P), ease pressure on the shift lever and then push the shift lever all the way into PARK (P) as you maintain brake application.
Page 106 DRIVE (D): This position is for normal driving. It provides the best fuel economy for your vehicle. If you need more power for passing, and you are: • Going less than 35 mph (56 km/h), push your accelerator pedal about halfway down. •...
Page 107 Notice: If you drive in LOW (L) for more than 25 miles (40 km) or at speeds over 55 mph (90 km/h), you could damage your engine and/or transmission. Use DRIVE (D) or INTERMEDIATE (I) as much as possible. Shift into LOW (L) only if your vehicle is going slower than 65 mph (105 km/h).
Page 108 The Driver Information Center (DIC) in the instrument cluster will change from the currently displayed message to the letter “M”, For MANUAL position, and a number indicating the requested gear range when moving the shift lever forward or rearward. ® While using the TAP-shift feature the transmission will have ﬁrmer shifting and sportier performance.
Page 109: Parking Brake
Parking Brake To set the parking brake, push down the parking brake pedal with your left foot. If the ignition is on, the brake system warning light will come on. See Brake System Warning Light on page 3-36. To release the parking brake, hold the regular brake pedal down with your right foot.
Page 110: Shifting Into Park
Shifting Into Park CAUTION: It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake ﬁrmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly.
Page 111: Shifting Out Of Park
Torque Lock If you are parking on a hill and you do not shift your transmission into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may ﬁnd it difficult to pull the shift lever out of PARK (P).
Page 112: Parking Over Things That Burn
To shift out of PARK (P) use the following: 1. Apply the brake pedal. 2. Then press the shift lever button. 3. Move the shift lever to the desired position. If you still are unable to shift out of PARK (P): 1.
Page 113: Running The Vehicle While Parked
Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle.
Page 114: Mirrors
Mirrors Manual Rearview Mirror Hold the mirror in the center to move it for a clearer view of behind your vehicle. Adjust the mirror to avoid glare from the headlamps behind you. Push the tab forward for daytime use and pull it for nighttime use. Manual Rearview Mirror with ®...
Page 115: Compass Calibration
Compass Operation Press the on/off button once to turn the compass on or off. When the ignition and the compass feature are on, the compass will show two character boxes for a few seconds. After a few seconds, the mirror will display the current compass direction.
Page 116: Outside Power Mirrors
3. Once the zone number appears on the display, press the on/off button quickly until you reach the correct zone number. If C appears in the compass window, the compass may need calibration. See “Compass Calibration” listed previously. Outside Power Mirrors The controls for the outside power mirrors are located on the inside of...
Page 117: Onstar System
® OnStar System OnStar uses several innovative technologies and live advisors to provide you with a wide range of safety, security, information, and convenience services. If your airbags deploy, the system is designed to make an automatic call to OnStar Emergency advisors who can request emergency services be sent to your location.
Page 118: Onstar Virtual Advisor
Available Services with Safe & Sound Plan • Automatic Notiﬁcation of Airbag Deployment • Advanced Automatic Crash Notiﬁcation (AACN) (If equipped) • Link to Emergency Services • Roadside Assistance • Stolen Vehicle Location Assistance • AccidentAssist • Remote Door Unlock/Vehicle Alert •...
Page 119: Onstar Steering Wheel Controls
OnStar Steering Wheel Controls Your vehicle may have a Talk/Mute button that can be used to interact with OnStar Hands-Free Calling. See Audio Steering Wheel Controls on page 3-78 for more information. On some vehicles, you may have to hold the button for a few seconds and give the command “ONSTAR”...
Page 120: Universal Home Remote System
Universal Home Remote System The Universal Home Remote System provides a way to replace up to three hand-held Radio-Frequency (RF) transmitters used to activate devices such as garage door openers, security systems, and home lighting. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Page 121 Be sure to keep the original remote control transmitter for use in other vehicles, as well as, for future programming. Only the original remote control transmitter is needed for Fixed Code programming. The programmed buttons should be erased when the vehicle is sold or the lease ends. See “Erasing Universal Home Remote Buttons”...
Page 122 2. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. It can usually be found where the hanging antenna wire is attached to the motor-head unit and may be a colored button. Press this button. After pressing this button, complete the following steps in less than 30 seconds.
Page 123 To program up to three devices: 1. To verify that the garage door opener is a Fixed Code unit, remove the battery cover on the hand held transmitter supplied by the manufacturer of the garage door opener motor. If there are a row of dip switches similar to the graphic above, the garage door opener is a Fixed Code unit.
Page 124 Example of Eight Dip Switches with Three Positions The panel of switches might not appear exactly as they do in the examples above, but they should be similar. The switch positions on the hand-held transmitter could be labeled, as follows: •...
Page 125 4. The indicator lights will blink slowly. Enter each switch setting from Step 2 into your vehicle’s Universal Home Remote. You will have two and one-half minutes to complete Step 4. Now press one button on the Universal Home Remote for each switch setting as follows: •...
Page 126: Storage Areas
Using Universal Home Remote Press and hold the appropriate button for at least half of a second. The indicator light will come on while the signal is being transmitted. Reprogramming Universal Home Remote Buttons Any of the three buttons can be reprogrammed by repeating the instructions.
Page 127: Center Console Storage
Pull down the door on the back of the center console to use the rear seat cupholders. Center Console Storage Your vehicle has a center console with two storage areas. To access the upper tray storage, lift the passenger side lever. To access the lower storage area, lift the driver side lever.
Page 128 Press the back of the switch and release it to open the sunroof to the vent position. From the vent position, press and release the back of the switch to express-open the sunroof. To stop the sunroof from express opening, press the switch again.
Page 129 Section 3 Instrument Panel Overview ...3-4 Hazard Warning Flashers ...3-6 Other Warning Devices ...3-6 Horn ...3-6 Tilt and Telescopic Steering Wheel ...3-6 Turn Signal/Multifunction Lever ...3-7 Turn and Lane-Change Signals ...3-7 Headlamp High/Low-Beam Changer ...3-8 Flash-to-Pass ...3-8 Windshield Wipers ...3-8 Windshield Washer ...3-9 Cruise Control ...3-10 Headlamps ...3-13...
Page 130 Section 3 Engine Coolant Temperature Gage ...3-39 Tire Pressure Light ...3-39 Malfunction Indicator Lamp ...3-40 Oil Pressure Light ...3-42 Security Light ...3-43 Cruise Control Light ...3-43 Highbeam On Light ...3-43 Fuel Gage ...3-44 Driver Information Center (DIC) ...3-45 DIC Operation and Displays ...3-45 DIC Warnings and Messages ...3-47 DIC Vehicle Personalization ...3-52 Instrument Panel...
Page 131 ✍ NOTES...
Page 132: Instrument Panel Overview
Instrument Panel Overview...
Page 133 The main components of your instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 3-28. B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7. C. Instrument Panel Cluster. See Instrument Panel Cluster on page 3-30. D.
Page 134: Hazard Warning Flashers
Hazard Warning Flashers The hazard warning ﬂashers let you warn the police and others that you have a problem. The front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is on the instrument panel. Press the button to make the front and rear turn signal lamps ﬂash on and off.
Page 135: Turn Signal/Multifunction Lever
Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: • Turn and Lane-Change Signals. See Turn and Lane-Change Signals on page 3-7. • Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 3-8. •...
Page 136: Headlamp High/Low-Beam Changer
Headlamp High/Low-Beam Changer To change the headlamps from low beam to high beam, push the turn signal/multifunction lever away from you. This light comes on in the instrument panel cluster if the high beam lamps are turned on while the ignition is in ON/RUN.
Page 137: Windshield Washer
(Delay): While the lever is in the intermittent position, turn the intermittent adjust band with this symbol on it up or down to select a shorter or longer delay between wiping cycles. To the left of the adjust band are bars, increasing in size from bottom to top, that indicate the frequency of the wipes.
Page 138: Cruise Control
Cruise Control Cruise control lets a speed of about 25 mph (40 km/h) or more be maintained without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below 25 mph (40 km/h). CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed.
Page 139: Resuming A Set Speed
(On/Off): Press to turn the cruise control system on and off. RES+ (Resume): Press RES+ to resume a set speed and to accelerate the speed. SET− (Set): Press SET– to set a speed and to decrease the speed. To set a speed do the following: 1.
Page 140 Reducing Speed While Using Cruise Control If the cruise control system is already engaged: • Push and hold the SET− until the desired lower speed is reached, then release it. • To slow down in very small amounts, brieﬂy push the SET−.
Page 141: Headlamps
Headlamps The band on the lever on the outboard side of the steering column operates the exterior lamps. The exterior lamp control has the following four positions: (Headlamps): Turn the band to this position to turn on the headlamps, parking lamps, and taillamps. (Parking Lamps): Turn the band to this position to turn on the parking lamps and taillamps only.
Page 142: Headlamps On Reminder
Headlamps on Reminder If you open the driver’s door and turn off the ignition while leaving the lamps on, you will hear a warning chime. Headlamps Off in Park This feature works when the ignition is in the ON/RUN position and it is dark outside. To turn the headlamps off when it is dark outside but keep other exterior lights on, turn the exterior lamp control to the parking lamp position.
Page 143: Automatic Headlamp System
Automatic Headlamp System When it is dark enough outside, the automatic headlamp system turns on the headlamps at the normal brightness along with other lamps such as the taillamps, sidemarker, parking lamps, and the instrument panel lights. The radio lights will also be dim. Your vehicle has a light sensor on top of the instrument panel that controls the automatic headlamp system.
Page 144: Fog Lamps
Fog Lamps If your vehicle has fog lamps, the fog lamp button is located on the instrument panel, to the left of the steering wheel. The ignition must be on for the fog lamps to work. Push the button to turn the fog lamps on. An indicator light in the button will glow when the fog lamps are on.
Page 145: Dome Lamp
Dome Lamp If the vehicle has a dome lamp with a switch, the following are the settings. (Off): Move the lever to this position to turn the lamp off, even when a door is open. (Door): Move the lever to this position so that the lamp comes on when a door is opened.
Page 146: Battery Run-Down Protection
Battery Run-Down Protection Your vehicle has a battery run-down feature designed to protect the vehicle’s battery. When any interior lamp (trunk, reading lamps, or dome lamp) is left on when the ignition is turned off, the battery run-down protection system automatically shuts the lamp off after 20 minutes.
Page 147: Climate Controls
Certain electrical accessories may not be compatible with the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a problem, see your retailer for additional information on the accessory power outlet. Notice: Adding any electrical equipment to your vehicle can damage it or keep other components from working as they should.
Page 148 To change the air delivery settings, turn the right knob to select one of the following: (Vent): This mode directs air to the instrument panel outlets. (Bi-Level): This mode directs half of the air to the instrument panel outlets, and the remaining air to the ﬂoor outlets.
Page 149: Maximum Air Conditioning
Maximum Air Conditioning On hot days, open the windows to let hot inside air escape; then close them. This helps reduce the time it takes for the vehicle to cool down. It also helps the air conditioning system operate more efficiently. For quick cool down on hot days, do the following: 1.
Page 150: Rear Window Defogger
(Defrost): This mode directs most of the air to the windshield with some air directed to the ﬂoor vents. In this mode, the system automatically forces outside air into the vehicle. The air-conditioning compressor will not run unless the outside temperature is at or below freezing.
Page 151: Automatic Climate Control System
If your vehicle has heated outside mirrors, the surface of the outside mirrors heat when the rear window defogger is activated. See Outside Power Mirrors on page 2-38. Notice: Do not use anything sharp on the inside of the rear window. If you do, you could cut or damage the warming grid, and the repairs would not be covered by the vehicle warranty.
Page 152 Use the steps below to place the entire system in automatic mode: 1. Turn the fan knob and the mode knob to the AUTO position. The current set temperature displays. When AUTO is selected, the air conditioning operation and air inlet is automatically controlled.
Page 153: Manual Operation
Manual Operation The air delivery mode or fan speed can be manually adjusted. (Off): Select this position on the fan knob to turn off the entire climate control system. Outside air still enters the vehicle. The direction can be changed by changing the mode position.
Page 154 When the weather is cool or damp, operating the system in recirculation for extended periods of time can cause fogging of the vehicle’s windows. To clear the fog, select either defog or defrost. Make sure the air conditioning is on. Allow the air conditioning to run automatically to help dehumidify the air.
Page 155 Defogging and Defrosting Fog on the inside of windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to choose from to clear fog or frost from the windshield.
Page 156: Outlet Adjustment
Remote Start Climate Control Operation If the vehicle has remote start and it is activated, the climate control system heats and cools the inside of the vehicle using the previous system settings before the vehicle was turned off. The climate control knobs will remain active during a remote start.
Page 157: Warning Lights, Gages, And Indicators
Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement.
Page 158: Instrument Panel Cluster
Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, how much fuel you are using, and many other things you will need to drive safely and economically.
Page 159: Speedometer And Odometer
Speedometer and Odometer Your speedometer lets you see your speed in miles per hour (mph) or kilometers per hour (km/h). See DIC Vehicle Personalization on page 3-52 for more information. Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada).
Page 160: Airbag Readiness Light
Passenger Safety Belt Reminder Light Several seconds after the engine is started, a chime sounds for several seconds to remind the front passenger to buckle their safety belt. This would only occur if the passenger airbag is enabled. See Passenger Sensing System on page 1-65 for more information.
Page 161: Passenger Airbag Status Indicator
CAUTION: If the airbag readiness light stays on after the vehicle is started, it means the airbag system may not be working properly. The airbags in the vehicle may not inﬂate in a crash, or they could even inﬂate without a crash. To help avoid injury, have the vehicle serviced right away.
Page 162 If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger’s frontal airbag and seat-mounted side impact airbag are enabled (may inﬂate). CAUTION: If the on indicator comes on when you have a rear-facing child restraint installed in the right front passenger’s seat, it means that the passenger sensing system has not turned...
Page 163: Charging System Light
If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer/retailer for service. CAUTION: If the airbag readiness light in the instrument panel cluster ever comes on and stays on, it means that something may be wrong with the airbag system.
Page 164: Brake System Warning Light
Brake System Warning Light Your vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop you. For good braking, though, you need both parts working well. If the warning light comes on, there is a brake problem. Have your brake system inspected right away.
Page 165: Antilock Brake System (Abs) Warning Light
Antilock Brake System (ABS) Warning Light This light will come on brieﬂy when you start the engine. That is normal. If the light does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. If the ABS light stays on, turn the ignition off, if the light comes on when you are driving, stop as soon as it is safely possible and turn the ignition off.
Page 166: Engine Coolant Temperature Warning Light
If this light is on and not ﬂashing, the TCS and potentially the ESC system have been disabled. Check your DIC messaging to determine which feature(s) is no longer functioning and whether it is because of the driver turning off the feature(s), or the system may not be working properly and your vehicle requires service.
Page 167: Tire Pressure Light
Engine Coolant Temperature Gage United States This gage shows the engine coolant temperature. If the gage pointer moves into the red area, the light comes on and you hear a chime, your engine is too hot! It means that your engine coolant has overheated. If you have been operating your vehicle under normal driving conditions and the gage reads hot, you should pull off the road, stop your vehicle and turn off the engine as...
Page 168: Malfunction Indicator Lamp
Malfunction Indicator Lamp Check Engine Light A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It ensures that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment.
Page 169 The following can prevent more serious damage to the vehicle: • Reduce vehicle speed. • Avoid hard accelerations. • Avoid steep uphill grades. • If towing a trailer, reduce the amount of cargo being hauled as soon as it is possible. If the light continues to ﬂash, when it is safe to do so, stop the vehicle.
Page 170: Maintenance Schedule
Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration. Here are some things to know to help the vehicle pass an inspection: •...
Page 171: Security Light
This light comes on brieﬂy when the engine is started as a check to make sure it works. If it does not, the vehicle needs service. If the light comes on and stays on, it means that oil is not ﬂowing through the engine properly. The vehicle could be low on oil and it might have some other system problem.
Page 172: Fuel Gage
Fuel Gage United States Your fuel gage tells you about how much fuel you have left, when the ignition is on. When the indicator nears empty, a LOW FUEL message will appear on the Driver Information Center (DIC). See DIC Warnings and Messages on page 3-47 for more information.
Page 173: Driver Information Center (Dic)
Driver Information Center (DIC) Your vehicle has a Driver Information Center (DIC). The DIC display gives you the status of many of your vehicle’s systems. The DIC is also used to display driver personalization menu modes and warning/status messages. All messages will appear in the DIC display, located at the bottom of the instrument panel cluster.
Page 174 TRIP A or TRIP B Press the information button until TRIP A or TRIP B display. These modes show the current distance traveled since the last reset for each trip odometer in either miles (mi) or kilometers (km). Both odometers can be used at the same time.
Page 175: Dic Warnings And Messages
AV (Average) SPEED Press the information button until AV SPEED displays. This mode shows the vehicle’s average speed in miles per hour (mph) or kilometers per hour (km/h). To reset the average vehicle speed, press and hold the reset button while AV SPEED is displayed. OIL LIFE Press the information button until OIL LIFE displays.
Page 176: Brake Fluid
AUTO (Automatic) LIGHTS ON This message displays if the automatic headlamp system is enabled with the headlamp switch. See Automatic Headlamp System on page 3-15 for more information. BRAKE FLUID This message displays, while the ignition is on, when the brake ﬂuid level is low. The brake system warning light on the instrument panel cluster also comes on.
Page 177: Ice Possible
ENG (Engine) PWR (Power) REDUCED This message displays when the vehicle’s engine power is reduced. Reduced engine power can affect the vehicle’s ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination.
Page 178 LOW TRACTION If your vehicle has the Traction Control System (TCS), this message displays and the ESC/TCS light on the instrument panel cluster ﬂashes when the system is actively limiting wheel spin. Slippery road conditions may exist if this message is displayed, so adjust your driving accordingly.
Page 179: Traction Off
SERVICE TRACTION If your vehicle has the Traction Control System (TCS), this message displays and a chime sounds when the system is not functioning properly. The ESC/TCS light also appears on the instrument panel cluster. This light stays on solid as long as the detected problem remains present.
Page 180: Dic Vehicle Personalization
DIC Vehicle Personalization Your vehicle has personalization capabilities that allow you to program certain features to a preferred setting. All of the features listed may not be available on your vehicle. Only the features available will be displayed on the DIC. The default settings for the features were set when your vehicle left the factory, but may have been changed from their default state since that time.
Page 181: Remote Start
REMOTE START If your vehicle has remote start, this feature allows remote start to be turned off or on. Remote start allows you to start the engine from outside of the vehicle using your Remote Keyless Entry (RKE) transmitter. When REMOTE START appears on the display, press and hold the reset button for at least one second to scroll through the available settings: OFF: The remote start feature will be disabled.
Page 182: Delay Lock
LIGHT FLASH This feature, which allows the vehicle’s exterior hazard/turn signal lighting to ﬂash every time the lock, unlock, or trunk release buttons on the Remote Keyless Entry (RKE) transmitter are pressed, can be enabled or disabled. When LIGHT FLASH appears on the display, press and hold the reset button for at least one second to scroll through the available settings: OFF: The exterior hazard/turn signal lighting will...
Page 183 AUTO UNLK (Unlock) This feature, which allows the vehicle to automatically unlock certain doors, can be enabled or disabled. When AUTO UNLK appears on the display, press and hold the reset button for at least one second to scroll through the available settings: ALL (default): All of the doors will automatically unlock.
Page 184 EXT (Exterior) LIGHTS This feature, which allows the vehicle’s exterior perimeter lighting to turn on each time the unlock button on the Remote Keyless Entry (RKE) transmitter is pressed, can be enabled or disabled. When EXT LIGHTS appears on the display, press and hold the reset button for at least one second to scroll through the available settings: OFF: The exterior perimeter lighting will not turn on...
Page 185: Audio System(S)
Audio System(s) Determine which radio your vehicle has and then read the pages following to familiarize yourself with its features. CAUTION: This system provides you with far greater access to audio stations and song listings. Giving extended attention to entertainment tasks while driving can cause a crash and you or others can be injured or killed.
Page 186: Setting The Clock
Setting the Clock If your vehicle has a radio with a single CD player, the radio has a button for setting the time and date. To set the time and date, follow the instructions: 1. Turn the radio on. 2. Press the button and the HR, MIN, MM, DD, YYYY (hour, minute, month, day, and year) displays.
Page 187: Radio(S) (Mp3)
To change the time default setting from 12 hour to 24 hour or to change the date default setting from month/day/year to day/month/year, follow these instructions: 1. Press the button and then the pushbutton located under the forward arrow tab. Once the time 12H and 24H, and the date MM/DD/YYYY (month, day, and year) and DD/MM/YYYY (day, month, and year) displays.
Page 188: Playing The Radio
Radio Data System (RDS) The audio system has a Radio Data System (RDS). The RDS feature is available for use only on FM stations that broadcast RDS information. This system relies upon receiving speciﬁc information from these stations and only works when the information is available. While the radio is tuned to an FM-RDS station, the station name or call letters display.
Page 189: Finding A Station
Finding a Station BAND: Press this button to switch between AM, FM, or XM™ (if equipped). The selection displays. (Tune): Turn this knob to select radio stations. © ¨ SEEK : Press the SEEK arrows to go to the previous or to the next station and stay there. To scan stations, press and hold either SEEK arrow for a few seconds until a beep sounds.
Page 190 The number of favorites pages can be setup using the MENU button. To setup the number of favorites pages, perform the following steps: 1. Press the MENU button to display the radio setup menu. 2. Press the pushbutton located below the FAV 1-6 tab.
Page 191: Adjusting The Speakers (Balance/Fade)
EQ (Equalization): Press this button to select preset equalization settings. To return to the manual mode, press the EQ button until Manual displays or start to manually adjust the bass, midrange, or treble by pressing the Adjusting the Speakers (Balance/Fade) BAL/FADE (Balance/Fade): To adjust balance or fade, press the knob until the speaker control tabs display.
Page 192: Radio Messages
Undesired XM™ categories can be removed through the setup menu. To remove an undesired category, perform the following: 1. Press the MENU button to display the radio setup menu. 2. Press the pushbutton located below the XM CAT tab. 3. Turn the knob to display the category you want removed.
Page 193 Playing a CD(s) (Six-Disc CD Player) LOAD : Press this button to load CDs into the CD player. This CD player holds up to six CDs. To insert one CD, do the following: 1. Press and release the button. 2. Wait for the message to insert the disc. 3.
Page 194 Care of Your CD Player Do not add any label to a CD, it could get caught in the CD player. If a CD is recorded on a personal computer and a description label is needed, try labeling the top of the recorded CD with a marking pen instead.
Page 195 RDM (Random): With the random setting, the tracks can be listened to in random, rather than sequential order, on one CD or all CDs in a six-disc CD player. To use random, do one of the following: • Press the CD/AUX button, or for a single CD player, insert a disc partway into the slot of the CD player.
Page 196: Using The Auxiliary Input Jack
CD Messages CHECK DISC: If this message displays and/or the CD ejects, it could be for one of the following reasons: • It is very hot. When the temperature returns to normal, the CD should play. • You are driving on a very rough road. When the road becomes smoother, the CD should play.
Page 197: Using An Mp3
CD/AUX (CD/Auxiliary): Press this button to play a CD while a portable audio device is playing. Press this button again and the system begins playing audio from the connected portable audio player. If a portable audio player is not connected, No Input Device Found displays. Using an MP3 MP3 CD-R or CD-RW Disc The radio plays MP3 ﬁles that were recorded on a...
Page 198 • Minimize the length of the ﬁle, folder or playlist names. Long ﬁle, folder, or playlist names, or a combination of a large number of ﬁles and folders, or playlists can cause the player to be unable to play up to the maximum number of ﬁles, folders, playlists, or sessions.
Page 199 Order of Play Tracks recorded to the CD-R or CD-RW are played in the following order: • Play begins from the ﬁrst track in the ﬁrst playlist and continues sequentially through all tracks in each playlist. When the last track of the last playlist has played, play continues from the ﬁrst track of the ﬁrst playlist.
Page 200 For the Six-Disc CD player, press and hold the eject button for two seconds to eject all discs. (Tune): Turn this knob to select MP3 ﬁles on the CD-R or CD-RW currently playing. © ¨ SEEK : Press the left SEEK arrow to go to the start of the current MP3 ﬁle, if more than 10 seconds have played.
Page 201 (Music Navigator): Use the music navigator feature to play MP3 ﬁles on the CD-R or CD-RW in order by artist or album. Press the pushbutton located below the music navigator tab. The player scans the disc to sort the ﬁles by artist and album ID3 tag information. It can take several minutes to scan the disc depending on the number of MP3 ﬁles recorded to the CD-R or CD-RW.
Page 202: Xm Radio Messages
XM Radio Messages XL (Explicit Language Channels): These channels, or any others, can be blocked at a customer’s request, by calling 1-800-852-XMXM (9696). XM Updating: The encryption code in the receiver is being updated, and no action is required. This process should take no longer than 30 seconds.
Page 203: Rear Seat Audio (Rsa)
Rear Seat Audio (RSA) Your vehicle may have rear seat audio (RSA). This feature allows rear seat passengers to listen to and control any of the music sources: radio, CDs, or other auxiliary sources. However, the rear seat passengers can only control the music sources the front seat passengers are not listening to.
Page 204: Rear Seat Audio Controls
The following functions are controlled by the RSA system: (Volume): Turn this knob to increase or to decrease the volume. The left knob controls the left wired headphones and the right knob controls the right wired headphones. (Power): Press this button to turn the system on or off.
Page 205 Headphones The RSA includes two wireless headphones that are dedicated to this system. These headphones are used to listen to media such as CDs or radio. The wireless headphones have an On/Off button and a volume control. Push the power button to turn on the headphones. An indicator light located on the headphones comes on.
Page 206: Theft-Deterrent Feature
Battery Replacement To change the batteries on the headphones, do the following: 1. Turn the screw to loosen the battery door located on the left side of the headphones. Slide the battery door open. 2. Replace the two batteries in the compartment. Make sure that they are installed correctly, using the diagram on the inside of the battery compartment.
Page 207: Radio Reception
(Mute/Voice Activation): Press this button to silence the system. Press this button again to turn the sound on. If your vehicle has OnStar hold this button for two seconds to activate voice on ® the OnStar system. See the OnStar page 2-39 in this manual for more information.
Page 208: Backglass Antenna
Backglass Antenna The AM-FM antenna is integrated with the rear window defogger, located in the rear window. Make sure that the inside surface of the rear window is not scratched and that the grid lines on the glass are not damaged. If the inside surface is damaged, it could interfere with radio reception.
Page 209: Driving Your Vehicle
Section 4 Your Driving, the Road, and the Vehicle ...4-2 Defensive Driving ...4-2 Drunk Driving ...4-2 Control of a Vehicle ...4-3 Braking ...4-4 Antilock Brake System (ABS) ...4-5 Braking in Emergencies ...4-6 Traction Control System (TCS) ...4-6 Electronic Stability Control (ESC) ...4-9 Steering ...4-11 Off-Road Recovery ...4-14 Passing ...4-14...
Page 210: Your Driving, The Road, And The Vehicle
Your Driving, the Road, and the Vehicle Defensive Driving Defensive driving means “always expect the unexpected.” The ﬁrst step in driving defensively is to wear your safety belt — See Safety Belts: They Are for Everyone on page 1-11. CAUTION: Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes.
Page 211: Control Of A Vehicle
Police records show that almost 40 percent of all motor vehicle-related deaths involve alcohol. In most cases, these deaths are the result of someone who was drinking and driving. In recent years, more than 17,000 annual motor vehicle-related deaths have been associated with the use of alcohol, with about 250,000 people injured.
Page 212: Braking
Braking See Brake System Warning Light on page 3-36. Braking action involves perception time and reaction time. First, you have to decide to push on the brake pedal. That is perception time. Then you have to bring up your foot and do it. That is reaction time. Average reaction time is about three-fourths of a second.
Page 213: Antilock Brake System (Abs)
Antilock Brake System (ABS) Your vehicle has the Antilock Brake System (ABS), an advanced electronic braking system that will help prevent a braking skid. When you start the engine and begin to drive away, ABS will check itself. You might hear a momentary motor or clicking noise while this test is going on, and you might even notice that the brake pedal moves a little.
Page 214: Braking In Emergencies
Remember: ABS does not change the time you need to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, you will not have time to apply the brakes if that vehicle suddenly slows or stops.
Page 215 If your vehicle is in cruise control when TCS begins to limit wheel spin, the cruise control will automatically disengage. When road conditions allow you to safely use it again, you may re-engage the cruise control. See Cruise Control on page 3-10. When this light is on solid and either the SERVICE TRACTION or TRACTION...
Page 216: Traction Control Operation
Traction Control Operation Traction control limits wheel spin by reducing engine power to the wheels (engine speed management) and by applying brakes to each individual wheel (brake-traction control) as necessary. The traction control system is enabled automatically when you start your vehicle, and it will activate and ﬂash the ESC/TCS light and display the LOW TRACTION message if it senses either of the front wheels are spinning or beginning to lose traction while driving.
Page 217: Electronic Stability Control (Esc)
Electronic Stability Control (ESC) Your vehicle may have an Electronic Stability Control (ESC) system which combines antilock brake, traction and stability control systems and helps the driver maintain directional control of the vehicle in most driving conditions. When you ﬁrst start your vehicle and begin to drive away, the system performs several diagnostic checks to ensure there are no problems.
Page 218 If the vehicle is in cruise control when the system begins to assist the driver maintain directional control of the vehicle, the ESC/TCS light will ﬂash and the cruise control will automatically disengage. When road conditions allow you to use cruise again, you may re-engage the cruise control.
Page 219: Steering
Steering Electric Power Steering If your vehicle has the electric power steering system and the engine stalls while you are driving, the power steering assist system will continue to operate until you are able to stop your vehicle. If you lose power steering assist because the electric power steering system is not functioning, you can steer, but it will take more effort.
Page 220 Traction in a curve depends on the condition of the tires and the road surface, the angle at which the curve is banked, and your speed. While in a curve, speed is the one factor you can control. Suppose you are steering through a sharp curve. Then you suddenly accelerate.
Page 221: Steering In Emergencies
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and ﬁnd a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Page 222: Off-Road Recovery
Off-Road Recovery Your vehicle’s right wheels can drop off the edge of a road onto the shoulder while driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that your vehicle straddles the edge of the pavement.
Page 223 Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to your vehicle’s three control systems.
Page 224: Driving At Night
Driving at Night Night driving is more dangerous than day driving because some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Night driving tips include: • Drive defensively. • Do not drink and drive. •...
Page 225: Other Rainy Weather Tips
CAUTION: Wet brakes can cause crashes. They might not work as well in a quick stop and could cause pulling to one side. You could lose control of the vehicle. After driving through a large puddle of water or a car/vehicle wash, lightly apply the brake pedal until the brakes work normally.
Page 226: Before Leaving On A Long Trip
Before Leaving on a Long Trip To prepare your vehicle for a long trip, consider having it serviced by your dealer/retailer before departing. Things to check on your own include: • Windshield Washer Fluid: Reservoir full? Windows clean — inside and outside? •...
Page 227: Winter Driving
CAUTION: If you do not shift down, the brakes could get so hot that they would not work well. You would then have poor braking or even none going down a hill. You could crash. Shift down to let the engine assist the brakes on a steep downhill slope.
Page 228: Driving On Snow Or Ice
Driving on Snow or Ice Most of the time, those places where the tires meet the road probably have good traction. However, if there is snow or ice between the tires and the road, you can have a very slippery situation. You have a lot less traction, or grip, and need to be very careful.
Page 229: If You Are Caught In A Blizzard
The Antilock Brake System (ABS) improves your vehicle’s stability when you make a hard stop on a slippery road. Even though you have ABS, begin stopping sooner than you would on dry pavement. See Antilock Brake System (ABS) on page 4-5. •...
Page 230 You can run the engine to keep warm, but be careful. 4-22 CAUTION: Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle.
Page 231: If Your Vehicle Is Stuck In Sand, Mud, Ice, Or Snow
Run your engine only as long as you must. This saves fuel. When you run the engine, make it go a little faster than just idle. That is, push the accelerator slightly. This uses less fuel for the heat that you get and it keeps the battery charged.
Page 232: Rocking Your Vehicle To Get It Out
Rocking Your Vehicle to Get It Out First, turn the steering wheel left and right to clear the area around the front wheels. Turn off any traction or stability system. See Traction Control System (TCS) on page 4-6 and Electronic Stability Control (ESC) on page 4-9.
Page 233 Tire and Loading Information Label Label Example A vehicle speciﬁc Tire and Loading Information label is attached to the vehicle’s center pillar (B-pillar). With the driver’s door open, you will ﬁnd the label attached below the door lock post (striker). The Tire and Loading Information label lists the number of occupant seating positions (A), and the maximum vehicle capacity weight (B) in kilograms...
Page 234 Steps for Determining Correct Load Limit Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
Page 235 Example 1 Item Description Maximum Vehicle Capacity Weight for Example 1 = Subtract Occupant Weight 150 lbs (68 kg) × 2 = Available Occupant and Cargo Weight = Total Item 1,000 lbs (453 kg) 300 lbs (136 kg) 700 lbs (317 kg) Example 2 Description Maximum Vehicle...
Page 236 Example 3 Item Description Maximum Vehicle Capacity Weight for Example 3 = Subtract Occupant Weight 200 lbs (91 kg) × 5 = Available Cargo Weight = Refer to your vehicle’s Tire and Loading Information label for speciﬁc information about your vehicle’s maximum vehicle capacity weight and 4-28 seating positions.
Page 237 Never exceed the GVWR for your vehicle or the Gross Axle Weight Rating (GAWR) for either the front or rear axle. CAUTION: Do not load the vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR).
Page 238: Towing
Towing Towing Your Vehicle To avoid vehicle damage, a platform or ﬂatbed trailer should be used to transport this vehicle. Consult your dealer/retailer or a professional towing service if you need to have your disabled vehicle towed. See Roadside Assistance Program on page 7-7. If you want to tow your vehicle behind another vehicle for recreational purposes (such as behind a motorhome), see “Recreational Vehicle Towing”...
Page 239: Dinghy Towing
Dinghy Towing When dinghy towing, the vehicle should be run at the beginning of each day and at each RV fuel stop for about ﬁve minutes. This will ensure proper lubrication of transmission components. To dinghy tow the vehicle from the front with all four wheels on the ground: 1.
Page 240: Dolly Towing
Notice: Towing your vehicle from the rear could damage it. Also, repairs would not be covered by the warranty. Never have your vehicle towed from the rear. Dolly Towing Tow the vehicle with the two rear wheels on the ground and the front wheels on a dolly: Do not tow the vehicle with the rear wheels on a dolly.
Page 241: Towing A Trailer
Towing a Trailer CAUTION: If you do not use the correct equipment and drive properly, you can lose control when you pull a trailer. For example, if the trailer is too heavy, the brakes may not work well — or even at all.
Page 242: If You Do Decide To Pull A Trailer
If You Do Decide to Pull a Trailer If you do, here are some important points: • There are many different laws, including speed limit restrictions, having to do with trailering. Make sure your rig will be legal, not only where you live but also where you’ll be driving.
Page 243: Weight Of The Trailer Tongue
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total or gross weight of your vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo you may carry in it, and the people who will be riding in the vehicle.
Page 244: Driving With A Trailer
Total Weight on Your Vehicle’s Tires Be sure your vehicle’s tires are inﬂated to the upper limit for cold tires. You’ll ﬁnd these numbers on the Tire-Loading Information label, See Loading the Vehicle on page 4-24. Then be sure you don’t go over the GVW limit for your vehicle, including the weight of the trailer tongue.
Page 245: Making Turns
Before you start, check the trailer hitch and platform (and attachments), safety chains, electrical connector, lamps, tires and mirror adjustment. If the trailer has electric brakes, start your vehicle and trailer moving and then apply the trailer brake controller by hand to be sure the brakes are working.
Page 246: Parking On Hills
When towing a trailer, the arrows on your instrument panel will ﬂash for turns even if the bulbs on the trailer are burned out. Thus, you may think drivers behind you are seeing your signal when they are not. It’s important to check occasionally to be sure the trailer bulbs are still working.
Page 247: Engine Cooling When Trailer Towing
When You Are Ready to Leave After Parking on a Hill 1. Apply your regular brakes and hold the pedal down while you: • start your engine • shift into a gear, and • release the parking brake. 2. Let up on the brake pedal. 3.
Page 248 ✍ NOTES 4-40...
Page 249: Service And Appearance Care
Section 5 Service ...5-3 Accessories and Modiﬁcations ...5-3 California Proposition 65 Warning ...5-4 California Perchlorate Materials Requirements ...5-4 Doing Your Own Service Work ...5-4 Adding Equipment to the Outside of the Vehicle ...5-5 Fuel ...5-5 Gasoline Octane ...5-6 Gasoline Speciﬁcations ...5-6 California Fuel ...5-6 Additives ...5-7 Fuels in Foreign Countries ...5-7...
Page 250 Section 5 Buying New Tires ...5-67 Different Size Tires and Wheels ...5-69 Uniform Tire Quality Grading ...5-69 Wheel Alignment and Tire Balance ...5-71 Wheel Replacement ...5-71 Tire Chains ...5-73 If a Tire Goes Flat ...5-73 Changing a Flat Tire ...5-74 Removing the Spare Tire and Tools ...5-75 Removing the Flat Tire and Installing the Spare Tire ...5-77...
Page 251: Service
Service For service and parts needs, visit your dealer/retailer. You will receive genuine Saturn parts and Saturn-trained and supported service people. Genuine Saturn parts have one of these marks. Accessories and Modiﬁcations When non-dealer/non-retailer accessories are added to your vehicle they can affect your vehicle’s performance...
Page 252: California Proposition 65 Warning
California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems (including some inside the vehicle), many ﬂuids, and some component wear by-products contain and/or emit these chemicals.
Page 253: Adding Equipment To The Outside Of The Vehicle
If you want to do some of your own service work, you should use the proper service manual. It tells you much more about how to service your vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on page 7-16.
Page 254: Gasoline Octane
Gasoline Octane If your vehicle has the 2.4L L4 engine (VIN Code B) or the 3.5L V6 engine (VIN Code N), use regular unleaded gasoline with a posted octane rating of 87 or higher. If the octane rating is less than 87, you might notice an audible knocking noise when you drive, commonly referred to as spark knock.
Page 255: Additives
Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that help prevent engine and fuel system deposits from forming, allowing the emission control system to work properly. In most cases, you should not have to add anything to the fuel. However, some gasolines contain only the minimum amount of additive required to meet U.S.
Page 256: Filling The Tank
Filling the Tank CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle.
Page 257 To remove the tethered fuel cap, turn it slowly counterclockwise. While refueling, hang the tethered fuel cap from the hook on the fuel door. CAUTION: Fuel can spray out on you if you open the fuel cap too quickly. If you spill fuel and then something ignites it, you could be badly burned.
Page 258 When replacing the fuel cap, turn it to the clockwise until it clicks. Make sure the cap is fully installed. The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere. See Malfunction Indicator Lamp on page 3-40.
Page 259: Filling A Portable Fuel Container
Filling a Portable Fuel Container CAUTION: Never ﬁll a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and your vehicle damaged if this occurs. To help avoid injury to you and others: •...
Page 260: Checking Things Under The Hood
Checking Things Under the Hood CAUTION: An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing, and tools away from any underhood electric fan. CAUTION: Things that burn can get on hot engine parts and start a ﬁre.
Page 261 2. Then go to the front of the vehicle and push the secondary hood release handle toward the driver side of the vehicle. 3. Lift the hood. 4. After the hood is slightly lifted, it will continue to open to the full position. Before closing the hood, be sure all the ﬁller caps are on properly.
Page 262: Engine Compartment Overview
Engine Compartment Overview When you open the hood on the 2.4L L4 engine, this is what you see: 5-14...
Page 263 A. Engine Air Cleaner/Filter. See Engine Air Cleaner/Filter on page 5-25. B. Engine Cooling Fan. See Cooling System on page 5-33. C. Engine Oil Fill Cap. See “When to Add Engine Oil” under Engine Oil on page 5-20. D. Engine Oil Dipstick (Out of view). See “Checking Engine Oil”...
Page 264 When you open the hood on the 3.5L V6 engine, this is what you see: 5-16...
Page 265 A. Engine Air Cleaner/Filter. See Engine Air Cleaner/Filter on page 5-25. B. Power Steering Fluid Reservoir. See Power Steering Fluid on page 5-37. C. Engine Cooling Fan. See Cooling System on page 5-33. D. Engine Oil Fill Cap. See “When to Add Engine Oil” under Engine Oil on page 5-20.
Page 266 When you open the hood on the 3.6L V6 engine, this is what you see: 5-18...
Page 267 A. Engine Air Cleaner/Filter. See Engine Air Cleaner/Filter on page 5-25. B. Power Steering Fluid Reservoir. See Power Steering Fluid on page 5-37. C. Engine Oil Fill Cap. See “When to Add Engine Oil” under Engine Oil on page 5-20. D.
Page 268: Engine Oil
Engine Oil Checking Engine Oil It is a good idea to check the engine oil every time you get fuel. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop.
Page 269 3.6LV6 Engine If the oil is below the cross-hatched area at the tip of the dipstick, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Speciﬁcations on page 5-104.
Page 270: What Kind Of Engine Oil To Use
What Kind of Engine Oil to Use Look for three things: • GM6094M Use only an oil that meets GM Standard GM6094M. • SAE 5W-30 SAE 5W-30 is best for the vehicle. If you are in an area of extreme cold, where the temperature falls below −20°F (−29°C), use either an SAE 5W-30 5-22 synthetic oil or an SAE 0W-30 oil.
Page 271: Engine Oil Additives
Engine Oil Additives Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM Standard GM6094M are all you need for good performance and engine protection. Engine Oil Life System When to Change Engine Oil Your vehicle has a computer system that lets you know when to change the engine oil and ﬁlter.
Page 272: How To Reset The Engine Oil Life System
How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change the engine oil and ﬁlter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change the oil prior to a CHANGE OIL SOON message being turned on, reset the system.
Page 273: Engine Air Cleaner/Filter
Engine Air Cleaner/Filter See Engine Compartment Overview on page 5-14 for the location of the engine air cleaner/ﬁlter. When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/ﬁlter at the Maintenance II intervals and replace it at the ﬁrst oil change after each 50,000 mile (80 000 km) interval.
Page 274 3. Inspect or replace the engine air cleaner/ﬁlter. 4. Align the ﬁlter correctly using the alignment tab. 5. Install the cover by guiding the tabs on the rim of the top cover into the bottom hinges and turn the cover down to close it. 6.
Page 275: Automatic Transmission Fluid
Automatic Transmission Fluid It is not necessary to check the transmission ﬂuid level. A transmission ﬂuid leak is the only reason for ﬂuid loss. If a leak occurs, take your vehicle to the dealer/retailer and have it repaired as soon as possible. Change the ﬂuid and ﬁlter at the intervals listed in Additional Required Services on page 6-6, and be sure to use the transmission ﬂuid listed in Recommended...
Page 276: What To Use
What to Use Use a mixture of one-half clean, drinkable water and ® one-half DEX-COOL coolant which will not damage aluminum parts. If you use this coolant mixture, you do not need to add anything else. CAUTION: Adding only plain water to the cooling system can be dangerous.
Page 277: Checking Coolant
Checking Coolant The engine coolant surge tank is located in the rear of the engine compartment. See Engine Compartment Overview on page 5-14 for more information on location. CAUTION: Turning the surge tank pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly.
Page 278: Adding Coolant
Adding Coolant If you need more coolant, add the proper DEX-COOL coolant mixture at the surge tank, but only when the engine is cool. If the surge tank is empty, a special ﬁll procedure is necessary. See Engine Overheating on page 5-30 and Cooling System on page 5-33. CAUTION: You can be burned if you spill coolant on hot engine parts.
Page 279: If Steam Is Coming From Your Engine
If Steam Is Coming From Your Engine CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Turn it off and get everyone away from the vehicle until it cools down.
Page 280: Overheated Engine Protection Operating Mode
If you get the overheat warning with no sign of steam, try this for a minute or so: 1. In heavy traffic, let the engine idle in N (Neutral) while stopped. If it is safe to do so, pull off the road, shift to P (Park) or N (NEUTRAL) and let the engine idle.
Page 281: Cooling System
Cooling System When you decide it is safe to lift the hood, this is what you see: 3.5L V6 Engine shown, 2.4L L4, 3.6L V6 Engines similar A. Engine Cooling Fans B. Engine Coolant Surge Tank C. Pressure Cap CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury.
Page 282: How To Add Coolant To The Coolant Surge Tank
The coolant level should be at or above the FULL COLD mark on the coolant surge tank. If it is not, you may have a leak at the pressure cap or in the radiator hoses, heater hoses, radiator, water pump, or somewhere else in the cooling system.
Page 283 If no coolant is visible in the surge tank, add coolant as follows: CAUTION: Steam and scalding liquids from a hot cooling system can blow out and burn you badly. They are under pressure, and if you turn the coolant surge tank pressure cap —...
Page 284 CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains eythylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. 1. Remove the coolant surge tank pressure cap when the cooling system, including the coolant surge tank pressure cap and upper radiator hose, is no longer hot.
Page 285: Power Steering Fluid
Power Steering Fluid See Engine Compartment Overview on page 5-14 for reservoir location. When to Check Power Steering Fluid Power steering ﬂuid is used in all vehicles with V6 engines. Vehicles with the 4-cylinder engine have electric power steering and do not use power steering ﬂuid.
Page 286: Windshield Washer Fluid
What to Use To determine what kind of ﬂuid to use, see Recommended Fluids and Lubricants on page 6-12. Always use the proper ﬂuid. Notice: Use of the incorrect ﬂuid may damage your vehicle and the damages may not be covered by your warranty.
Page 287: Brakes
Brakes Brake Fluid The brake master cylinder reservoir is ﬁlled with DOT-3 brake ﬂuid. See Engine Compartment Overview on page 5-14 for the location of the reservoir. There are only two reasons why the brake ﬂuid level in the reservoir might go down. The ﬁrst is that the brake ﬂuid goes down to an acceptable level during normal brake lining wear.
Page 288: Brake Wear
What to Add Use only new DOT-3 brake ﬂuid from a sealed container. See Recommended Fluids and Lubricants on page 6-12. Always clean the brake ﬂuid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir.
Page 289: Brake Adjustment
CAUTION: The brake wear warning sound means that soon the brakes will not work well. That could lead to an accident. When you hear the brake wear warning sound, have your vehicle serviced. Notice: Continuing to drive with worn-out brake pads could result in costly brake repair.
Page 290: Battery
Battery Your vehicle has a maintenance free battery. When it is time for a new battery, see your dealer/retailer for one that has the replacement number shown on the original battery’s label. See Engine Compartment Overview on page 5-14 for battery location. Warning: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause...
Page 291: Jump Starting
Jump Starting If your battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. CAUTION: Batteries can hurt you. They can be dangerous because: •...
Page 292 4. Open the hoods and locate the batteries. Find the positive (+) and negative (−) terminal locations on each vehicle. Your vehicle’s positive (+) terminal is located under a red tethered cap on the battery. The negative (–) terminal is located under a black tethered cap on the battery.
Page 293 CAUTION: Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock.
Page 294 9. Connect the other end of the negative (−) cable at least 18 inches (45 cm) away from the dead battery, but not near engine parts that move. The electrical connection is just as good there, and the chance of sparks getting back to the battery is much less. 10.
Page 295: Headlamp Aiming
To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative (−) cable from the vehicle that had the dead battery. 2. Disconnect the black negative (−) cable from the vehicle with the good battery. 3.
Page 296: Taillamps, Turn Signal, Sidemarker, Stoplamps And Back-Up Lamps
Taillamps, Turn Signal, Sidemarker, Stoplamps and Back-up Lamps A. Turn Signal Lamp C. Backup Lamp B. Stoplamp/Taillamp D. Sidemarker Lamp If a stoplamp or a taillamp needs to be replaced, see your dealer/retailer. 5-48 To replace a sidemarker lamp, turn signal lamp, or a back-up lamp: 1.
Page 297: License Plate Lamp
5. Remove the taillamp assembly. 6. Remove the wiring harness from the taillamp assembly by lifting the release tab. 7. Turn the bulb socket counterclockwise to remove it. 8. Pull the bulb from the socket. 9. Install a new bulb. 10.
Page 298: Replacement Bulbs
3. Turn the bulb socket counterclockwise and pull the bulb straight out of the socket. 4. Push the new bulb in and turn it clockwise to install. 5. Push the license plate lamp in and turn it through the fascia opening. 6.
Page 299: Tires
4. Turn the blade toward you and continue to slide forward. 5. Install the new blade onto the arm connector and make sure the grooved areas are fully set in the locked position. For the proper type and size, see Maintenance Replacement Parts on page 6-13.
Page 300: Tire Sidewall Labeling
Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall. Passenger (P-Metric) Tire Example 5-52 (A) Tire Size The tire size is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type, and service description.
Page 301 (F) Uniform Tire Quality Grading (UTQG) Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction, and temperature resistance. For more information see Uniform Tire Quality Grading on page 5-69. (G) Maximum Cold Inﬂation Load Limit Maximum load that can be carried and the maximum pressure needed to support that load.
Page 302: Tire Size
(F) Tire Size A combination of letters and numbers deﬁne a tire’s width, height, aspect ratio, construction type, and service description. The letter T as the ﬁrst character in the tire size means the tire is for temporary use only. (G) TPC Spec (Tire Performance Criteria Speciﬁcation) Original equipment tires designed...
Page 303: Tire Terminology And Deﬁnitions
Tire Terminology and Deﬁnitions Air Pressure The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight This means the combined weight of optional accessories.
Page 304 GAWR RR Gross Axle Weight Rating for the rear axle. See Loading the Vehicle on page 4-24. Intended Outboard Sidewall an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa) The metric unit for air pressure. Light Truck (LT-Metric) Tire light duty trucks and some multipurpose passenger vehicles.
Page 305 Radial Ply Tire A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. A metal support for a tire and upon which the tire beads are seated. Sidewall The portion of a tire between the tread and the bead.
Page 306: Inﬂation - Tire Pressure
Inﬂation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inﬂation or over-inﬂation is all right. It is not. If your tires do not have enough air (under-inﬂation), you can get the following: •...
Page 307: How To Check
How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inﬂated simply by looking at them. Radial tires may look properly inﬂated even when they are under-inﬂated. Check the tire’s inﬂation pressure when the tires are cold.
Page 308 Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inﬂation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly.
Page 309: Tire Pressure Monitor Operation
Tire Pressure Monitor Operation The Tire Pressure Monitor System (TPMS) is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly, excluding the spare tire and wheel assembly. The TPMS sensors monitor the air pressure in the vehicle’s tires and transmits the tire pressure readings to a receiver located in the vehicle.
Page 310: Tpms Malfunction Light And Message
TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light ﬂashes for about one minute and then stays on for the remainder of the ignition cycle.
Page 311: Tpms Sensor Matching Process
TPMS Sensor Matching Process Each TPMS sensor has a unique identiﬁcation code. Any time you replace one or more of the TPMS sensors or rotate the vehicle’s tires, the identiﬁcation codes need to be matched to the new tire/wheel location. The sensors are matched, to the tire/wheel locations, in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver...
Page 312: Tire Inspection And Rotation
7. The passenger side rear turn signal comes on to indicate that corner sensor is ready to be learned. Proceed to the passenger side rear tire and repeat the procedure in Step 5. 8. The driver side rear turn signal comes on to indicate that corner sensor is ready to be learned.
Page 313 When rotating the vehicle’s tires, always use the correct rotation pattern shown here. Do not include the compact spare tire in the tire rotation. After the tires have been rotated, adjust the front and rear inﬂation pressures as shown on the Tire and Loading Information label.
Page 314: When It Is Time For New Tires
When It Is Time for New Tires Various factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions inﬂuence when you need new tires. One way to tell when it is time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch...
Page 315: Buying New Tires
Buying New Tires GM has developed and matched speciﬁc tires for your vehicle. The original equipment tires installed on your vehicle, when it was new, were designed to meet General Motors Tire Performance Criteria Speciﬁcation (TPC Spec) system rating. If you need replacement tires, GM strongly recommends that you get tires with the same TPC Spec rating.
Page 316 CAUTION: If you use bias-ply tires on the vehicle, the wheel rim ﬂanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly, causing a crash. Use only radial-ply tires with the wheels on the vehicle. If you must replace your vehicle’s tires with those that do not have a TPC Spec number, make sure they are the same size, load range, speed rating,...
Page 317: Different Size Tires And Wheels
You may increase the chance that you will crash and suffer serious injury. Only use Saturn speciﬁc wheel and tire systems developed for your vehicle, and have them properly installed by a Saturn certiﬁed technician.
Page 318 Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speciﬁed government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100.
Page 319: Wheel Alignment And Tire Balance
WARNING: The temperature grade for this tire is established for a tire that is properly inﬂated and not overloaded. Excessive speed, underinﬂation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance.
Page 320: Used Replacement Wheels
If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new Saturn original equipment parts. This way, you will be sure to have the right wheel, wheel bolts and wheel nuts for your vehicle.
Page 321: Tire Chains
Tire Chains CAUTION: Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension or other vehicle parts. The area damaged by the tire chains could cause you to lose control of the vehicle and you or others may be injured in a crash.
Page 322: Changing A Flat Tire
A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you would use in a skid. In any rear blowout remove your foot from the accelerator pedal. Get the vehicle under control by steering the way you want the vehicle to go.
Page 323: Removing The Spare Tire And Tools
CAUTION: (Continued) To be even more certain the vehicle will not move, you should put blocks at the front and rear of the tire farthest away from the one being changed. That would be the tire, on the other side, at the opposite end of the vehicle. When your vehicle has a ﬂat tire, use the following example as a guide to assist you in the placement of wheel blocks.
Page 324 5. Remove the extension bolt that is clipped to the jack. You need this later to store the ﬂat tire. 6. Remove the jack and wheel wrench from the trunk. The tools you will be using include the wheel wrench (A) and jack (B).
Page 325: Removing The Flat Tire And Installing The Spare Tire
3. Extend the handle on the wheel wrench by pressing the button with your index ﬁnger and pulling on the end of the wrench. You must do this before using the wheel wrench. Removing the Flat Tire and Installing the Spare Tire 1.
Page 326 4. Use the wheel wrench to loosen all the wheel nuts. Do not remove them yet. 5-78 5. Position the lift head at the jack location nearest the ﬂat tire. Make sure all of the jack lift head is touching the jacking ﬂange under the body.
Page 327 CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. CAUTION: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall.
Page 328 8. Remove all of the wheel nuts. CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
Page 329 10. Remove any rust or dirt from the wheel bolts, mounting surfaces, and spare wheel. 11. Install the compact spare tire. CAUTION: Never use oil or grease on bolts or nuts. Because the nuts might come loose. The vehicle’s wheel could fall off, causing a crash. 12.
Page 330 CAUTION: Incorrect or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to a crash. If you have to replace them, be sure to get new original equipment wheel nuts. Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to the proper torque speciﬁcation.
Page 331: Storing A Flat Or Spare Tire And Tools
Storing a Flat or Spare Tire and Tools CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. To store the ﬂat tire and jack in the compact spare tire compartment: 1.
Page 332: Compact Spare Tire
A. Cover E. Bracket B. Retainer F. Jack, Wheel Wrench, C. Spare Tire and Bolt Extension D. Wing Nut G. Bolt The compact spare is for temporary use only. Replace the compact spare tire with a full-size tire as soon as you can.
Page 333: Appearance Care
Appearance Care Interior Cleaning Your vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on your upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces. Regular vacuuming is recommended to remove particles from your upholstery.
Page 334: Fabric/Carpet
Do not clean your vehicle using: • A knife or any other sharp object to remove a soil from any interior surface. • A stiff brush. It can cause damage to your vehicle’s interior surfaces. • Heavy pressure or aggressive rubbing with a cleaning cloth.
Page 335: Instrument Panel, Vinyl, And Other Plastic Surfaces
To clean: 1. Saturate a lint-free, clean white cloth with water or club soda. 2. Wring the cloth to remove excess moisture. 3. Start on the outside edge of the soil and gently rub toward the center. Continue cleaning, using a clean area of the cloth each time it becomes soiled.
Page 336: Care Of Safety Belts
Care of Safety Belts Keep belts clean and dry. CAUTION: Do not bleach or dye safety belts. If you do, it may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.
Page 337: Cleaning Exterior Lamps/Lenses
High pressure car washes may cause water to enter the vehicle. Avoid using high pressure washes closer than 12 inches (30 cm) to the surface of the vehicle. Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals. Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses.
Page 338: Windshield And Wiper Blades
Protecting Exterior Bright Metal Parts Bright metal parts should be cleaned regularly to keep their luster. Washing with water is all that is usually needed. However, you may use chrome polish on chrome or stainless steel trim, if necessary. Use special care with aluminum trim. To avoid damaging protective trim, never use auto or chrome polish, steam or caustic soap to clean aluminum.
Page 339: Tires
The surface of these wheels is similar to the painted surface of the vehicle. Do not use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because the surface could be damaged. Do not use chrome polish on aluminum wheels. Notice: If you drive your vehicle through an automatic car wash that has silicone carbide tire cleaning brushes, you could damage the aluminum...
Page 340: Underbody Maintenance
Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, ﬂoor pan, and exhaust system even though they have corrosion protection.
Page 341: Vehicle Identiﬁcation
Description Removes swirl marks, ﬁne Swirl Remover Polish scratches, and other light surface contamination. Removes light scratches Cleaner Wax and protects ﬁnish. Cleans, shines, and Foaming Tire Shine Low protects tires. No wiping Gloss necessary. Medium foaming shampoo. Cleans Wash Wax Concentrate and lightly waxes.
Page 342: Service Parts Identiﬁcation Label
Engine Identiﬁcation The eighth character in the VIN is the engine code. This code helps identify the vehicle’s engine, speciﬁcations, and replacement parts. See “Engine Speciﬁcations” under Capacities and Speciﬁcations on page 5-104 for your vehicle’s engine code. Service Parts Identiﬁcation Label This label is on the inside of the glove box.
Page 343: Power Windows And Other Power Options
Power Windows and Other Power Options Fuses in the fuse block protect the power windows. When the current load is too heavy, the fuse opens protecting the circuit until the problem is ﬁxed. Fuses The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers and fusible links.
Page 344 Your vehicle might not have all the fuses and features listed. 5-96...
Page 345 Fuses Usage POWER Power Mirrors MIRRORS Electronic Power Steering Cruise Control Switch, Passenger RUN/CRANK Airbag Status Indicator HVAC Heating Ventilation Air Conditioning BLOWER HIGH Blower - High Speed Relay CLUSTER/ Instrument Panel Cluster, THEFT Theft Deterrent System ® ONSTAR OnStar Not Used INSTALLED AIRBAG (IGN)
Page 346: Engine Compartment Fuse Block
Fuses ROOF/HEAT Sunroof, Power Windows SEAT Not Used INSTALLED Not Used INSTALLED AIRBAG Airbag (Battery) (BATT) SPARE FUSE Spare Fuse Holder HOLDER SPARE FUSE Spare Fuse Holder HOLDER SPARE FUSE Spare Fuse Holder HOLDER 5-98 Usage SPARE FUSE HOLDER FUSE PULLER Fuse Puller Engine Compartment Fuse Block Your vehicle may not be equipped with all the fuses and features listed.
Page 347 Fuses Usage Air Conditioner Clutch Electronic Throttle Control Engine Control Module IGN 1 (LZ4) Fuses Usage Transmission Control Module Ignition 1 Mass Airﬂow Sensor (LY7) Emission 5-99...
Page 348 Fuses Left Headlamp Low-Beam Horn Right Headlamp Low-Beam Front Fog Lamps Left Headlamp High-Beam Right Headlamp High-Beam Engine Control Module BATT (LY7 & LE5) Windshield Wiper Antilock Brake System (IGN 1) Engine Control Module IGN 1 (LY7 & LE5) Cooling Fan 1 Cooling Fan 2 Run Relay, Heating, Ventilation, Air Conditioning Blower...
Page 349: Rear Compartment Fuse Block
Relays Usage Cooling Fan 1 Cooling Fan Series/Parallel Cooling Fan 2 Starter Run/Crank, Ignition Powertrain Air Conditioning Clutch High Beam Front Fog Lamps Horn Low-Beam Headlamp Windshield Wiper 1 Windshield Wiper 2 Daytime Running Lamps Stoplamps Diodes Usage Wiper Rear Compartment Fuse Block The rear compartment fuse block is located in the trunk of the vehicle.
Page 350 Fuses Passenger Seat Controls Driver Seat Controls Not Used Not Used 5-102 Usage Fuses Usage Emission 2, Canister Vent Solenoid Park Lamps, Instrument Panel Dimming Not Used...
Page 351 Fuses Usage Not Used Not Used Sunroof Controls Not Used Not Used Audio Ampliﬁer Heated Seat Controls Not Used Remote Keyless Entry (RKE) System, XM™ Satellite Radio, UGDO Back-up Lamps Not Used Not Used Auxiliary Power Outlets Not Used Trunk Release Fuses Usage Rear Defog...
Page 352: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. Please refer to Recommended Fluids and Lubricants on page 6-12 for more information. Application Air Conditioning Refrigerant R134a Automatic Transmission Automatic Transmission – 4 Speed (Bottom Pan Removal) Automatic Transmission –...
Page 353 Application Fuel Tank Wheel Nut Torque All capacities are approximate. When adding, be sure to ﬁll to the appropriate level, as recommended in this manual. Engine 2.4L L4 3.5L V6 3.6L V6 Engine Speciﬁcations VIN Code Transmission Automatic Automatic Automatic Capacities English Metric...
Page 354 ✍ NOTES 5-106...
Page 355 Section 6 Maintenance Schedule ...6-2 Introduction ...6-2 Maintenance Requirements ...6-2 Your Vehicle and the Environment ...6-2 Using the Maintenance Schedule ...6-2 Scheduled Maintenance ...6-4 Additional Required Services ...6-6 Maintenance Footnotes ...6-7 Maintenance Schedule Owner Checks and Services ...6-9 At Each Fuel Fill ...6-9 At Least Once a Month ...6-9 At Least Once a Year ...6-10 Recommended Fluids and Lubricants ...6-12...
Page 356: Maintenance Schedule
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended ﬂuids and lubricants as prescribed in this manual are necessary to keep your vehicle in good working condition. Any damage caused by failure to follow scheduled maintenance might not be covered by warranty.
Page 357 The services in Scheduled Maintenance on page 6-4 should be performed when indicated. See Additional Required Services on page 6-6 and Maintenance Footnotes on page 6-7 for further information. CAUTION: Performing maintenance work on a vehicle can be dangerous. In trying to do some jobs, you can be seriously injured.
Page 358: Scheduled Maintenance
Scheduled Maintenance When the CHANGE OIL SOON message in the Driver Information Center (DIC) comes on, it means that service is required for your vehicle. Have your vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if you are driving under the best conditions, the engine oil life system may not indicate that vehicle service is necessary for over a year.
Page 359 Change engine oil and ﬁlter. See Engine Oil on page 5-20. Reset oil life system. See Engine Oil Life System on page 5-23. An Emission Control Service. Visually check for any leaks or damage. See footnote (j). Inspect engine air cleaner ﬁlter. If necessary, replace ﬁlter. See Engine Air Cleaner/Filter on page 5-25.
Page 360: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Service and Miles (Kilometers) Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components.
Page 361: Maintenance Footnotes
Service and Miles (Kilometers) Engine cooling system service (or every ﬁve years, whichever occurs ﬁrst). An Emission Control Service. See footnote (i). Inspect engine accessory drive belt. An Emission Control Service. See footnote (m). Maintenance Footnotes (a) Visually inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chaﬁng, etc.
Page 362 (e) Make sure the safety belt reminder light and safety belt assemblies are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. Have any torn or frayed safety belts replaced.
Page 363: Engine Oil Level Check
Owner Checks and Services These owner checks and services should be performed at the intervals speciﬁed to help ensure vehicle safety, dependability, and emission control performance. Your dealer/retailer can assist with these checks and services. Be sure any necessary repairs are completed at once. Whenever any ﬂuids or lubricants are added to the vehicle, make sure they are the proper ones, as shown in Recommended Fluids and Lubricants on page 6-12.
Page 364: At Least Once A Year
At Least Once a Year Starter Switch Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle.
Page 365: Ignition Transmission Lock Check
Ignition Transmission Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK/OFF in each shift lever position. • The ignition should turn to LOCK/OFF only when the shift lever is in PARK (P). •...
Page 366: Recommended Fluids And Lubricants
Recommended Fluids and Lubricants Fluids and lubricants identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer/retailer. Usage Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Engine Oil Certiﬁed for Gasoline Engines starburst symbol.
Page 367: Maintenance Replacement Parts
Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained from your Saturn retailer/dealer. Part Engine Air Cleaner/Filter Engine Oil Filter 2.4L L4 Engine 3.5L V6 Engine* 3.6L V6 Engine Spark Plugs 2.4L L4 Engine 3.5L V6 Engine...
Page 368: Engine Drive Belt Routing
Engine Drive Belt Routing 3.5L V6 Engine 2.4L I4 Engine 6-14...
Page 369 3.6L V6 Engine 6-15...
Page 370: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2. Any additional information from Owner Checks and Services on page 6-9 can be added on the following record pages. You should retain all maintenance receipts.
Page 371 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-17...
Page 372 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-18...
Page 373: Customer Assistance Information
Reporting Safety Defects ...7-15 Reporting Safety Defects to the United States Government ...7-15 Reporting Safety Defects to the Canadian Government ...7-16 Reporting Safety Defects to Saturn ...7-16 Service Publications Ordering Information ...7-16 Vehicle Data Recording and Privacy ...7-17 Event Data Recorders ...7-18 ®...
Page 374: Customer Assistance And Information
Saturn. Together we are committed to providing our customers with unparalleled service, before, during, and after the purchase of a Saturn vehicle, for total customer satisfaction. We call this the Saturn Difference. Normally, any concerns with the sales transaction or the operation of the vehicle are resolved by the retailer’s sales or service departments.
Page 375 Saturn vehicle. However, if you continue to remain unsatisﬁed after following the procedure outlined in Steps One and Two, Saturn and its retailers offer the additional assistance of a neutral party through our voluntary participation in a mediation/ arbitration program called Better Business Bureau (BBB) Auto Line.
Page 376 For further information concerning eligibility in the Canadian Motor Vehicle Arbitration Plan (CAMVAP), call toll-free 1-800-207-0685. Alternatively, you may call the Saturn Customer Communication Centre, 1-800-263-1999, or you may write to: Mediation/Arbitration Program c/o Customer Communication Centre...
Page 377: Online Owner Center
Online Owner Center (United States only) This is a resource for your Saturn ownership needs. Speciﬁc vehicle information can be found in one place. The Online Owner Center allows you to: • Get e-mail service reminders. • Access information about your speciﬁc vehicle, including tips and videos and an electronic version of this owner manual.
Page 378: Customer Assistance For Text Telephone (Tty) Users
Customer Assistance for Text Telephone (TTY) Users To assist owners who have hearing difficulties, Saturn has installed special TDD (Telecommunication Devices for the Deaf) equipment in its Saturn Customer Assistance Center. Any hearing or speech-impaired customer who has access to a TDD or to a conventional Text Telephone (TTY) can communicate with Saturn by dialing 1-800-TDD-6000.
Page 379: Roadside Assistance Program
(Text Telephone (TTY): 1-800-889-2438). For vehicles purchased in Canada, call 1-800-268-6800. Service is available 24 hours a day, 365 days a year. As the owner of a new Saturn vehicle, you are automatically enrolled in the Saturn Roadside Assistance Program.
Page 380 However, any cost for parts and labor for non-warranty repairs are the responsibility of the driver. Saturn and General Motors of Canada Limited reserve the right to limit services or reimbursement to an owner or driver when, in their sole discretion, the claims...
Page 381: Calling For Assistance
Roadside Assistance is not part of or included in the coverage provided by the New Vehicle Limited Warranty. Saturn and General Motors of Canada Limited reserve the right to make any changes or discontinue the Roadside Assistance program at any time without notiﬁcation.
Page 382: Courtesy Transportation
Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait, Saturn helps to minimize your inconvenience by providing several transportation options. Depending on the circumstances, your retailer can offer you one of the following:...
Page 383: Additional Program Information
Saturn for shuttle service. In addition, for U.S. customers, should you arrange transportation through a friend or relative, limited reimbursement for reasonable fuel expenses may be available.
Page 384: Collision Damage Repair
Collision Damage Repair If your vehicle is involved in a collision and it is damaged, have the damage repaired by a qualiﬁed technician using the proper equipment and quality replacement parts. Poorly performed collision repairs diminish your vehicle’s resale value, and safety performance can be compromised in subsequent collisions.
Page 385: Repair Facility
Repair Facility We recommend that you choose a collision repair facility that meets your needs before you ever need collision repairs. Your dealer/retailer may have a collision repair center with GM-trained technicians and state of the art equipment, or be able to recommend a collision repair center that has GM-trained technicians and comparable equipment.
Page 386 • Give only the necessary and requested information to police and other parties involved in the crash. Do not discuss your personal condition, mental frame of mind, or anything unrelated to the crash. This will help guard against post-crash legal action. •...
Page 387: Reporting Safety Defects
However, NHTSA cannot become involved in individual problems between you, your retailer or Saturn Corporation. To contact NHTSA, call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153);...
Page 388: Reporting Safety Defects To The Canadian Government
Oshawa, Ontario L1H 8P7 Service Publications Ordering Information Service Manuals A variety of publications are available to you. Saturn service manuals are written for trained technicians, and in some cases, specialized tools and equipment are necessary to complete certain repairs. However,...
Page 389: Vehicle Data Recording And Privacy
ﬁx your vehicle. They can help a technician service your vehicle better. Most bulletins apply to conditions affecting a small number of vehicles. Your Saturn retailer or a qualiﬁed technician may have to determine if a speciﬁc bulletin applies to your vehicle. To order Saturn bulletins, call Saturn Publications at 1-800-2-SATURN or visit saturn-publications.com to order online.
Page 390: Event Data Recorders
EDR. Saturn will not access this data or share it with others except: with the consent of the vehicle owner or, if the vehicle is leased, with the consent of the lessee; in response to an official request of police or similar government office;...
Page 391: Onstar
RFID technology in Saturn vehicles does not use or record personal information or link with any other Saturn system containing personal information.
Page 392 ✍ NOTES 7-20...
Page 393 Accessories and Modiﬁcations ... 5-3 Accessory Power Outlets ... 3-18 Adding Equipment to Your Airbag-Equipped Vehicle ... 1-70 Additives, Fuel ... 5-7 Add-On Electrical Equipment ... 5-94 Adjustable Throttle and Brake Pedal ... 2-24 Air Cleaner/Filter, Engine ... 5-25 Air Conditioning ... 3-19, 3-23 Airbag Passenger Status Indicator ...
Page 394 Audio System ... 3-57 Audio Steering Wheel Controls ... 3-78 Backglass Antenna ... 3-80 Chime Level Adjustment ... 3-80 Radio Reception ... 3-79 Rear Seat Audio (RSA) ... 3-75 Setting the Clock ... 3-58 Theft-Deterrent Feature ... 3-78 XM™ Satellite Radio Antenna System ... 3-80 Audio System(s) ...
Page 395 Chains, Tire ... 5-73 Charging System Light ... 3-35 Check Engine Light ... 3-40 Checking Things Under the Hood ... 5-12 Chemical Paint Spotting ... 5-92 Child Restraints Child Restraint Systems ... 1-37 Infants and Young Children ... 1-34 Lower Anchors and Tethers for Children ... 1-42 Older Children ...
Page 396 Telephone (TTY) Users ... 7-6 Customer Assistance Offices ... 7-6 Customer Satisfaction Procedure ... 7-2 GM Mobility Reimbursement Program ... 7-6 Reporting Safety Defects to Saturn ... 7-16 Reporting Safety Defects to the Canadian Government ... 7-16 Reporting Safety Defects to the United States Government ...
Page 397 EDR ... 7-17 Electrical System Add-On Equipment ... 5-94 Engine Compartment Fuse Block ... 5-98 Fuses ... 5-95 Instrument Panel Fuse Block ... 5-95 Power Windows and Other Power Options ... 5-95 Rear Compartment Fuse Block ... 5-101 Windshield Wiper Fuses ... 5-94 Electronic Immobilizer ®...
Page 398 Fluid Automatic Transmission ... 5-27 Power Steering ... 5-37 Windshield Washer ... 5-38 Fog Lamp Fog ... 3-16 Folding Rear Seat ... 1-9 Fuel ... 5-5 Additives ... 5-7 California Fuel ... 5-6 Filling a Portable Fuel Container ... 5-11 Filling the Tank ...
Page 399 Headlamps (cont.) Halogen Bulbs ... 5-47 High/Low Beam Changer ... 3-8 On Reminder ... 3-14 Headlamps Off in Park ... 3-14 Heated Seats ... 1-4 Heater ... 3-19, 3-23 Engine Coolant ... 2-24 Highbeam On Light ... 3-43 Highway Hypnosis ... 4-18 Hill and Mountain Roads ...
Page 400 Light (cont.) Cruise Control ... 3-43 Engine Coolant Temperature Warning ... 3-38 Highbeam On ... 3-43 Malfunction Indicator ... 3-40 Oil Pressure ... 3-42 Passenger Airbag Status Indicator ... 3-33 Safety Belt Reminders ... 3-31 Security ... 3-43 Tire Pressure ... 3-39 Lighting Entry/Exit ...
Page 401 Message DIC Warnings and Messages ... 3-47 Mirrors Automatic Dimming Rearview with OnStar and Compass ... 2-36 Manual Rearview Mirror ... 2-36 Manual Rearview Mirror with OnStar Outside Automatic Dimming Mirror ... 2-38 Outside Power Mirrors ... 2-38 MP3 ... 3-69 MyGMLink.com ...
Page 402 Park Brake ... 2-31 Parking Over Things That Burn ... 2-34 Passenger Airbag Status Indicator ... 3-33 Passenger Sensing System ... 1-65 Passing ... 4-14 ® PASS-KEY III+ Electronic Immobilizer ... 2-18 ® PASS-Key III+ Electronic Immobilizer Operation ... 2-19 Perchlorate Materials Requirements, California ...
Page 403 Replacement Parts, Maintenance ... 6-13 Reporting Safety Defects Canadian Government ... 7-16 Saturn ... 7-16 United States Government ... 7-15 Restraint System Check Checking the Restraint Systems ... 1-72 Replacing Restraint System Parts After a Crash ... 1-73 Retained Accessory Power (RAP) ... 2-22 Roadside Assistance Program ...
Page 404 Service, Scheduling Appointments ... 7-9 Servicing Your Airbag-Equipped Vehicle ... 1-70 Setting the Clock ... 3-58 Sheet Metal Damage ... 5-91 Shifting Into Park ... 2-32 Shifting Out of Park ... 2-33 Signals, Turn and Lane-Change ... 3-7 Spare Tire Compact ...
Page 405 Tires (cont.) Changing a Flat Tire ... 5-74 Cleaning ... 5-91 Compact Spare Tire ... 5-84 Different Size ... 5-69 If a Tire Goes Flat ... 5-73 Inﬂation - Tire Pressure ... 5-58 Inspection and Rotation ... 5-64 Installing the Spare Tire ... 5-77 Pressure Monitor Operation ...
Page 406 Vehicle Data Recording and Privacy ... 7-17 Vehicle Identiﬁcation Number (VIN) ... 5-93 Service Parts Identiﬁcation Label ... 5-94 Vehicle Personalization DIC ... 3-52 Vehicle, Remote Start ... 2-6 Ventilation Adjustment ... 3-28 Visors ... 2-16 Warning Lights, Gages, and Indicators ... 3-29 Warnings DIC Warnings and Messages ...

Saturn 2008 Aura Owner's Manual

Section 1 Seats and Restraint Systems

Seats and Restraint Systems

Front Seats

Rear Seats

Safety Belts

Child Restraints

Airbag System

Restraint System Check

Section 2 Features and Controls

Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Onstar System

Universal Home Remote System

Storage Areas

Sunroof

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Driving Your Vehicle

Your Driving, the Road, and the Vehicle

Towing

Section 5 Service and Appearance Care

Service and Appearance Care

Service

Fuel

Checking Things under the Hood

Headlamp Aiming

Bulb Replacement

Windshield Wiper Blade Replacement

Tires

Appearance Care

Vehicle Identiﬁcation

Electrical System

Capacities and Speciﬁcations

Quick Links

Chapters

Related Manuals for Saturn 2008 Aura

Summary of Contents for Saturn 2008 Aura