Sanyo DS31590 Owner's Manual page 7

PROGRAMMING MULTIMEDIA REMOTE CONTROL
Find your code. It is next to the brand name
of your equipment in the charts below and on
page 8. (The illustrated example is for a
Sanyo VCR.)
Press and hold VCR, CABLE, or
SAT/AUX key.
Press button
and hold down.
Using the NUMBER keys on the remote,
enter the three-digit code number for your
VCR, Cable box, or Satellite. The key will
flash 5 times when released if the code
was accepted.
Enter Code:
Example: For
a Sanyo VCR, Enter
code "200" (from
chart on page 8).
BRAND NAME ........CODE
SANSUI ....................
SANYO......................
SCOTT........................
Cable Box Codes Chart
BRAND NAME
ABC .................................. 304,306,309,312,313
..........................................
AIM .................................... 321
ARCHER .............................. 334
CONTEC .............................. 302,305,307,308
..........................................
CPI ...................................... 319
DIAMOND .......................... 320
EAGLE ................................ 313
EMERSON............................ 334
GEN. INSTRUMENTS .......... 303,309,311,322,323
GOODMIND ........................ 334
HAMLIN .............................. 320,330
JERROLD ............................ 303,308,309,311
..........................................
MAGNAVOX ........................ 301,322
MEMOREX .......................... 313,314,332
MOVIE TIME ...................... 306,310,314
NORTHCOAST .................... 316
NSC .................................... 305,306,314
OAK .................................... 305,318,320
PANASONIC ........................ 302,307,317
PARAGON .......................... 313,314
PHILIPS .............................. 313,314,325,329
The VCR, and Cable modes will accept
only each mode's specific code type. If you
enter an invalid code, the Mode key will
light, but it will not flash, repeat Step 2.
The SAT/AUX mode will accept all code
types.
VCR TV CABLE
SAT
AUX
To Operate Your...
VCR—Press the VCR key.
Cable Box—Press the CABLE key.
Television—Press the TV key.
Satellite/Auxiliary (other)—Press the
After programming
is confirmed, enter
your codes in the
200
,201,202,203
spaces provided
and on the back of
the remote control.
CODE NO. BRAND NAME
PIONEER ............................ 312,317,333
314,318,322,324 PROSCAN .......................... 328
RADIO SHACK .................... 334
RCA .................................... 328
REGAL ................................ 320
311,318,320,324 REMBRANT ........................ 305
SAMSUNG .......................... 310,312
SCI. ATLANTA .................... 324,327
SIGNAL .............................. 310
SIGNATURE ........................ 300,322
SPRUCER .......................... 307,316
STARCOM .......................... 309,321,322,323,332
STARGATE .......................... 310,321,334
TOCOM .............................. 300,304,305,306,307
313,319,322,323 TOSHIBA ............................ 316,331
TELEVIEW .......................... 310
UNITED CABLE .................. 309
UNIKA ................................ 314
U.S. ELECTRONICS ............ 309,322,324
VIEWSTAR .......................... 313,315,326
WARDS .............................. 322
WARNER ............................ 312
ZENITH .............................. 316,331
(Continued on pages 8 and 9.)
Press the POWER and CHANNEL keys.
If they operate properly, programming is
completed. If not, use another code, if
available and repeat steps
each piece of equipment you have (VCR,
Cable Converter Box, and/or Satellite
Receiver).
SAT/AUX key.
VCR CODE
CABLE BOX
CODE
SAT/AUX CODE
............ CODE NO.
QuickTips
Make sure batteries
have been installed
correctly.
The Remote Control
must be programmed
before it will operate
your VCR, Cable Box,
and for or Satellite Receiver.
Point the remote
control toward the
equipment you want
to operate. Objects
between the remote
control and the
equipment may
cause misoperation
of the remote
control function.
The remote control
will not operate my
VCR, Cable Box, or
Satellite/Auxiliary.
– Press the VCR
CABLE or
SAT/AUX key.
– Reprogram the
remote control.
Special key func-
tions: The VIDEO/
TV•VCR key func-
tions as the VCR's
TV/VCR key when
the Remote Control is
set for VCR operation.
Write your codes in
the spaces provided
on the back of your
Remote Control for
quick reference.
Need help?
visit our website at
www.sanyoctv.co
Call 1-800-877-5032
m
or
7