Safety Precautions CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE REAR COVER. NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product.
If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.) 10. When cleaning, do not spray water directly onto parts of the product.
Important Safety Instructions Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers)
Contents Overview ... 6 About this guide ...6 Product overview ...6 Main features ...6 Components ...6 Checking components in the package ...6 Components of your camera ...7 Installation ... 8 Setting switches ...8 Setting function switches ...8 Connecting cables and setting switches ...10 Installing camera ...
Overview About this guide ❚ This user guide includes basic instructions for the product. It is recommended that all users read this guide before use. This guide is divided as follows: Chapter 1, “Overview,” introduces the user guide and product related information. (This chapter) ...
Components of your camera Your camera has the following components: 1. Cover dome: Covers the lens and main body to protect them. 2. Main body: Includes a lens, a switch board, a PCB board, screws, and such. 3. Locker: Used to open or close the Cover dome.
Installation Setting switches ❚ Setting function switches To set the available functions on your camera, adjust eight switches as shown below: 1. Switch 1 (LL): When this switch is set to OFF, the camera operates in the internal synchronization mode, while when it is set to ON, the camera operates in the line lock mode. In the internal synchronization mode, the camera always uses an inside crystal oscillator for synchronization.
Page 9
2. Switch 2 (LSS): This sens-up mode accumulates the image fields in memory to reduce noise but increase the brightness and contrast rate. When this switch is set to ON, the camera automatically switches to a maximum of 128 times of image acquisition speed to implement a clear picture for darker image.
Connecting cables and setting switches ❚ To check the camera view and set the switches 1. Remove the Cover dome. For more details about the removing procedures, see “Installation procedure,” in the Installing camera section on the next page. 2. Adjust the function of your camera using the Switch board while you are viewing the image on the screen.
Installing camera ❚ Before installation Before installing your camera, you have to read the following cautions: You have to check whether the location (ceiling or wall) can bear five times the weight of your camera. Don’t let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise it may cause a breakdown or fire.
4. When you install the Mount bracket on the ceiling, remove the Ceiling mount opener by pressing it hard to connect the line attached on your camera through the hole in the ceiling. Otherwise, you can use the empty space opposite to the CAMERA FRONT sign for line connection.
Appendix A: Specifications for NTSC Standard Item Product type CCTV color dome camera Power input AC 24V ± 10% (60Hz ± 0.3 Hz), DC 12V +10%/-5% Broadcast type NTSC Standard color system (525 Lines, 60 Fields) Power consumption Approx. 1.6W Image device 1/3 inch IT Type Super-HAD CCD SCC-B5311N, B5313N, B5315N...
Page 15
Item Line Lock (LL) Sens-up; Low Speed Shutter(LSS) Horizontal Reverse (H-REV) Vertical Reverse (V-REV) Backlight compensation (BLC) Controls Auto gain control (AGC) Switching between color and B&W by day and night change (D/N) Automatic white balancing (AWB) Digital noise reduction (DNR) Dynamic CCD defect compensation Product color SCC-B531xN : White / SCC-B531xBN : Black...
Appendix B: Specifications for PAL Standard Item Product type CCTV color dome camera Power input AC 24V ± 10% (50Hz ± 0.3 Hz), DC 12V +10%/-5% Broadcast type PAL Standard color system (625 Lines, 50 Fields) Power consumption Approx. 1.6W Image device 1/3 inch IT Type Super-HAD CCD SCC-B5311P, B5313P, B5315P...
Page 17
Item Line Lock (LL) Sens-up; Low Speed Shutter(LSS) Horizontal Reverse (H-REV) Vertical Reverse (V-REV) Backlight compensation (BLC) Controls Auto gain control (AGC) Switching between color and B&W by day and night change (D/N) Automatic white balancing (AWB) Digital noise reduction (DNR) Dynamic CCD defect compensation Product color SCC-B531xP : White / SCC-B531xBP : Black...
Page 19
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.