First Alert CO600 User Manual

UNDERSTANDING YOUR CO ALARM
USER'S MANUAL
WH T YOU SEE ND HE R DURING INST LL TION
120V PLUG-IN CARBON MONOXIDE ALARM
WHEN YOU FIRST PLUG-IN THE CO L RM:
WITH SILENCE FEATURE
HORN: Silent
POWER/ L RM LIGHT: Shines continuously
UNDER NORM L CONDITIONS ( C POWER):
HORN: Silent
POWER/ L RM LIGHT: Shines continuously
WHEN YOU TEST THE CO L RM:
HORN: Sounds loudly - 4 beeps, pause, 4 beeps, pause
POWER/ L RM LIGHT: Flashes rapidly
Model
WH T YOU SEE ND HE R UNDER DIFFERENT CONDITIONS
CO600
~
WHEN THE ELECTRICITY COMES B CK ON FTER
120V C ,
CONFORMS TO
F ILURE:
60 Hz, 0.09
UL STD 2034
HORN: Silent
M08-0152-008 S 08/12 Printed in Mexico POWER/ L RM LIGHT: Shines continuously.
IF THE CO L RM IS NOT OPER TING PROPERLY (M LFUNCTION
IMPORT NT! SIGN L):
PLE SE RE D C REFULLY ND S VE.
HORN: 3 chirps every minute
This user's manual contains important information about your Carbon POWER/ L RM LIGHT: 3 flashes approximately once a minute.
Monoxide (CO) larm's operation. If you are installing this CO larm
IF THE CO L RM H S RE CHED ITS END OF LIFE:
for use by others, you must leave this manual—or a copy of it—with
the end user.
HORN: 5 chirps every minute
POWER/ L RM LIGHT: 5 flashes approximately once a minute.
© 2012 BRK Brands, Inc. ll rights reserved.
Distributed by BRK Brands, Inc.
WH T YOU SEE ND HE R IF CO IS DETECTED
3901 Liberty Street Road, urora, IL 60504-8122
Consumer ffairs: (800) 323-9005 • www.firstalert.com
L RM LEVELS OF CO RE DETECTED:
HORN: Sounds loudly - 4 beeps, pause, 4 beeps, pause.
INTRODUCTION
This sequence repeats for as long as the unit is in alarm.
POWER/ L RM LIGHT: Flashes rapidly
BASIC SAFETY INFORMATION
IF YOU SILENCE THE L RM:
HORN: Silent for about 4 minutes
• Dangers, Warnings, and Cautions alert you to important
POWER/ L RM LIGHT: Flashes rapidly
operating instructions or to potentially hazardous situations.
Pay special attention to these items. Note: fter 4 minutes, if CO levels drop below alarm levels, the unit
will remain silent and return to normal operation. If CO presence
• THIS IS NOT SMOKE L RM! This CO larm is designed to
still indicates a potentially dangerous situation, the horn will sound
detect carbon monoxide from NY source of combustion. It is
again.
NOT designed to detect smoke, fire, or any other gas.
IF THE CO LEVELS RETURN TO NORM L:
• This CO larm is approved for use in single-family residences.
HORN: Silent
POWER/ L RM LIGHT: Shines continuously
• This CO larm will only indicate the presence of carbon
monoxide gas at the sensor. Carbon monoxide gas may be
present in other areas.
INSTALLATION
WHERE TO INSTALL CO ALARMS
• The Silence Feature is for your convenience only and will not
correct a CO problem. lways check your home for a potential The National Fire Protection ssociation (NFP ) recommends that a CO
problem after any alarm. Failure to do so can result in injury or larm should be centrally located outside of each separate sleeping
death. area in the immediate vicinity of the bedrooms. For added protection,
install additional CO larms in each separate bedroom, and on every
• This CO larm should receive continuous 120V C, 60 Hz, pure
level of your home.
sine wave electrical power. Do not use in an extension cord or
outlet controlled by a dimmer or switch. If your bedroom hallway is longer than 40 feet (12 meters), install a CO
larm at BOTH ends of the hallway.
• NEVER ignore your Carbon Monoxide larm if it alarms. Refer
to "If Your CO larm Sounds" for more information. Failure to
do so can result in injury or death.
• Test the CO larm once a week. If the CO larm ever fails to
test correctly, have it replaced immediately! If the CO larm is
not working properly, it cannot alert you to a problem.
• This product is intended for use in ordinary indoor locations of
family living units. It is not designed to measure CO levels in
compliance with Occupational Safety and Health dministration
(OSH ) commercial or industrial standards. Individuals with
medical conditions that may make them more sensitive to
carbon monoxide may consider using warning devices which
provide audible and visual signals for carbon monoxide con-
centrations under 30 ppm. For additional information on carbon
monoxide and your medical condition contact your physician.
FCC Compliance
REQUIRED TO MEET NFPA RECOMMENDATIONS
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules. These SUGGESTED AREAS FOR INSTALLING ADDITIONAL CO ALARMS
limits are designed to provide reasonable protection against harmful
In a Single-level Home:
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
• Install at least one CO larm near or within each separate sleeping
accordance with the instructions, may cause harmful interference to
area.
radio communications.
• For added protection, install an additional CO larm at least 20 feet
However, there is no guarantee that the interference will not occur in a (6 meters) away from the furnace or fuel burning heat source.
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
In a Multi-level Home:
the equipment off and on, the user is encouraged to try to correct the
• Install at least one CO larm near or within each separate sleeping
interference by one or more of the following measures:
area.
• Reorient or relocate the receiving antenna.
• For added protection, install at least one CO larm on each level of
• Increase the separation between the equipment and receiver.
the home.
• Connect the equipment into an outlet on a circuit different from that • For added protection, install an additional CO larm at least 20 feet
of the receiver.
(6 meters) away from the furnace or fuel burning heat source.
• Consult the dealer or an experienced radio or TV technician for help.
Warning: Changes or modifications to the product, not expressly
This unit should receive continuous electrical power. Choose an
approved by First lert / BRK Brands, Inc., could void the user's
outlet where it cannot be accidentally unplugged or switched off by
authority to operate the equipment.
children. Keep small children away from the unit. Teach them not to
play with it or unplug it. Explain what the alarms mean.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. WHERE CO ALARMS SHOULD NOT BE
INSTALLED
HOW YOUR CO ALARM WORKS
DO NOT LOCATE THIS CO ALARM:
GENERAL INFORMATION • In garages, kitchens, furnace rooms, or in any extremely dusty,
dirty or greasy areas.
• Closer than 15 feet (4.6 meters) from a furnace or other fuel
Leave your CO larm plugged in year-round. CO problems can
burning heat source, or fuel burning appliances like a water heater.
occur any time during the year, and this larm can only alert you if
• Within 5 feet (1.5 meters) of any cooking appliance.
it is plugged in and receiving power.
• In extremely humid areas. This larm should be at least 10 feet (3
When fully powered, the unit samples the air and takes a new reading
meters) from a bath or shower, sauna, humidifier, vaporizer, dish-
about every second. microchip inside the unit stores each reading,
washer, laundry room, utility room or other source of high humidity.
and remembers the levels of CO it has been exposed to over time.
• In areas where temperature is colder than 40˚ F (4.4˚ C) or hotter
The larm sounds when it has been exposed to a "critical" level of
than 100˚ F (37.8˚ C). These areas include non-airconditioned crawl
CO (measured in parts per million or "ppm") within a specified time
spaces, unfinished attics, uninsulated or poorly insulated ceilings,
(measured in minutes). This CO larm features a permanently installed
porches, and garages.
sensor, an indicator light, and an 85 dB alarm horn. It also has a Silence
Feature to temporarily quiet the alarm horn. • In turbulent air, like near ceiling fans, heat vents, air conditioners,
fresh air returns, or open windows. Blowing air may prevent CO
from reaching the sensors.
MALFUNCTION WARNING
• In direct sunlight.
This unit performs daily self-diagnostic tests. If the larm malfunctions,
it should be replaced immediately. • In outlets covered by curtains or other obstruction.
THE COVER OF YOUR CO ALARM
• This CO larm is designed for use inside a single-family home
or apartment. It is not meant to be used in common lobbies,
hallways, or basements of multi-family buildings unless work-
1
ing CO larms are also installed in each family living unit.
CO larms in common areas may not be heard from inside
individual family living units.
• This CO larm alone is not a suitable substitute for complete
detection systems in places which house many people, like
hotels or dormitories, unless a CO larm is also placed in each
unit.
3 • DO NOT use this CO larm in warehouses, industrial or com-
mercial buildings, special-purpose non-residential buildings, or
2
airplanes. This CO larm is specifically designed for residential
use, and may not provide adequate protection in non-residential
applications.
1 Test/Silence Button 2 POWER/ L RM Light (Red)
3 (Behind Cover) larm Horn: 85 dB audible alarm
for test, alarm, and unit malfunction warning
1
HOW TO INSTALL YOUR CO ALARM
Read "Where To Install Your CO larm" before starting.
Before you start installation, find the pair of self-adhesive labels
included with this CO larm. On each label write in the phone number
of your emergency responder (like 911) and a qualified appliance tech-
nician. Place one label near the CO larm, and the other label in the
"fresh air" location you plan to go if the alarm sounds.
1. Plug the unit into a standard
UNSWITCHED 120V C outlet.
The unit should be located
where it can wake you if it
alarms at night.
2. Make sure the POWER/ L RM light
shines continuously when you plug it.
3. Test by pressing the Test/Silence button firmly until the unit sounds:
four loud beeps, pause, 4 beeps. During testing, the POWER/
L RM light will flash rapidly. This is normal.
POWER
IF YOUR CO ALARM SOUNDS
ctuation of your CO larm indicates the presence of carbon
monoxide (CO) which can kill you. In other words, when your CO
larm sounds, you must not ignore it!
IF THE ALARM SIGNAL SOUNDS:
1. Operate the Test/Silence button.
2. Call your emergency services, fire department or 911. Write down
the number of your local emergency service here:
_____________________________________________________________
3. Immediately move to fresh air—outdoors or by an open door or
window. Do a head count to check that all persons are accounted
for. Do not re-enter the premises, or move away from the open door
or window until the emergency services responder has arrived, the
premises have been aired out, and your CO larm remains in its
normal condition.
4. fter following steps 1-3, if your CO larm reactivates within a
24-hour period, repeat steps 1-3 and call a qualified appliance
technician to investigate for sources of CO from fuel-burning
equipment and appliances, and inspect for proper operation of this
equipment. If problems are identified during this inspection have the
equipment serviced immediately. Note any combustion equipment
not inspected by the technician, and consult the manufacturers'
instructions, or contact the manufacturers directly, for more
information about CO safety and this equipment. Make sure that
motor vehicles are not, and have not, been operating in an attached
garage or adjacent to the residence. Write down the number of a
qualified appliance technician here:
_____________________________________________________________
" L RM-MOVE TO FRESH IR"
If you hear the alarm horn and the red light is flashing,
move everyone to a source of fresh air.
DO NOT unplug the CO larm!
larms have various limitations. See "General Limitations of CO
larms" for details.
USING THE SILENCE FEATURES
The Silence Feature is for your convenience only and will not correct
a CO problem. lways check your home for a potential problem
after any alarm. Failure to do so can result in injury or death.
NEVER unplug your CO larm to silence the horn. Use the silence
BEDROOM BEDROOM BEDROOM
feature. Unplugging the CO larm removes your protection! See "If
Your CO larm Sounds" for details on responding to an alarm.
When CO reaches alarm levels the alarm will sound— repeating horn
KITCHEN GARAGE
HALL
LIVING ROOM pattern: 4 beeps, a pause, 4 beeps, etc. Press and hold the Test/Silence
button until the horn is silent. The initial Silence cycle will last approxi-
mately 4 minutes.
NOTE: fter initial 4-minute Silence cycle, the CO larm re-evaluates
BASEMENT
present CO levels and responds accordingly. If CO levels remain poten-
tially dangerous—or start rising higher—the horn will start sounding
again.
While the detector is silenced:
If the CO larm...
Is silent for only 4 minutes,
then starts sounding loudly—
4 beeps, pause,
4 beeps, pause
If the CO larm...
Remains silent after you
pressed the Test/Silence
button
SILENCING THE END OF LIFE SIGNAL
This silence feature can temporarily quiet the End of Life warning
"chirp" for up to 2 days. You can silence the End of Life warning "chirp"
by pressing the Test/Silence button. The horn will chirp, acknowledging
that the End of Life silence feature has been activated.
fter approximately 2 days, the End of Life "chirp" will resume.
TESTING AND MAINTENANCE
WEEKLY TESTING
Press the Test/Silence button on the larm cover until alarm sounds.
During testing, you will hear a loud alarm sequence – 4 beeps, pause,
4 beeps, pause.
The alarm sequence should last 5-6 seconds. If it does not alarm, make
sure the unit is fully plugged into an unswitched outlet. If the unit still
does not alarm, replace it immediately.
• If the larm ever fails to test properly, replace it immediately.
Products under warranty may be returned to the manufacturer
for replacement. See "Limited Warranty" at the end of this
manual.
• DO NOT stand close to the larm when the horn is sounding.
Exposure at close range may be harmful to your hearing. When
testing, step away when horn starts sounding.
• NEVER use vehicle exhaust! Exhaust may cause permanent
damage and voids your warranty.
REGULAR MAINTENANCE
To keep the CO larm working properly:
• Test it every week as described in "Weekly Testing."
• Vacuum the CO larm cover at least once a month, using the soft
brush attachment. Never use water, cleaners, or solvents, since
they may damage the unit. Test the larm again after vacuuming.
DO NOT spray cleaning chemicals or insect sprays directly on or
near the CO larm. DO NOT paint over the CO larm. Doing so
may cause permanent damage.
• Household cleaners, aerosol chemicals and other contaminants
can affect the sensor. When using any of these materials near the
CO larm, make sure the room is well ventilated.
• If your home is being fumigated, unplug the unit temporarily and
put it where it will not be exposed to chemicals or fumes. When
fumigation is complete and all traces of fumes clear, plug the unit
back in and retest it.
2
WHAT YOU NEED TO KNOW ABOUT CO
WHAT IS CO?
CO is an invisible, odorless, tasteless gas produced when fossil fuels
do not burn completely, or are exposed to heat (usually fire). Electrical
appliances typically do not produce CO.
These fuels include: Wood, coal, charcoal, oil, natural gas, gasoline,
kerosene, and propane.
Common appliances are often sources of CO. If they are not properly
maintained, are improperly ventilated, or malfunction, CO levels can rise
C Plug
quickly. CO is a real danger now that homes are more energy efficient.
" ir-tight" homes with added insulation, sealed windows, and other
weatherproofing can "trap" CO inside.
SYMPTOMS OF CO POISONING
These symptoms are related to CO POISONING and should be
discussed with LL household members.
Mild Exposure:
Slight headache, nausea, vomiting, fatigue ("flu-like" symptoms).
Medium Exposure:
Throbbing headache, drowsiness, confusion, fast heart rate.
Extreme Exposure:
Convulsions, unconsciousness, heart and lung failure. Exposure to
carbon monoxide can cause brain damage, death.
Some individuals are more sensitive to CO than others, including
people with cardiac or respiratory problems, infants, unborn
babies, pregnant mothers, or elderly people can be more quickly
and severely affected by CO. Members of sensitive populations
should consult their doctors for advice on taking additional
precautions.
FINDING THE SOURCE OF CO AFTER AN ALARM
Carbon monoxide is an odorless, invisible gas, which often makes it
difficult to locate the source of CO after an alarm. These are a few of
the factors that can make it difficult to locate sources of CO:
• House well ventilated before the investigator arrives.
• Problem caused by "backdrafting."
• Transient CO problem caused by special circumstances.
Because CO may dissipate by the time an investigator arrives, it may be
difficult to locate the source of CO. BRK Brands, Inc. shall not be obli-
gated to pay for any carbon monoxide investigation or service call.
POTENTIAL SOURCES OF CO IN THE HOME
Fuel-burning appliances like: portable heater, gas or wood burning
fireplace, gas kitchen range or cooktop, gas clothes dryer.
Damaged or insufficient venting: corroded or disconnected water
heater vent pipe, leaking chimney pipe or flue, or cracked heat
exchanger, blocked or clogged chimney opening.
Improper use of appliance/device: operating a barbecue grill or
vehicle in an enclosed area (like a garage or screened porch).
Transient CO Problems: "transient" or on-again-off-again CO problems
can be caused by outdoor conditions and other special circumstances.
The following conditions can result in transient CO situations:
1. Excessive spillage or reverse venting of fuel appliances caused by
outdoor conditions such as:
• Wind direction and/or velocity, including high, gusty winds. Heavy
This means...
air in the vent pipes (cold/humid air with extended periods
CO levels are still potentially
between cycles).
dangerous.
• Negative pressure differential resulting from the use of exhaust
fans.
• Several appliances running at the same time competing for limited
This means...
fresh air.
CO levels are dropping.
• Vent pipe connections vibrating loose from clothes dryers,
furnaces, or water heaters.
• Obstructions in or unconventional vent pipe designs which can
amplify the above situations.
2. Extended operation of unvented fuel burning devices (range, oven,
fireplace).
3. Temperature inversions, which can trap exhaust close to the ground.
4. Car idling in an open or closed attached garage, or near a home.
These conditions are dangerous because they can trap exhaust in your
home. Since these conditions can come and go, they are also hard to
recreate during a CO investigation.
HOW CAN I PROTECT MY FAMILY?
CO larm is an excellent means of protection. It monitors the air and
sounds a loud alarm before carbon monoxide levels become threaten-
ing for average, healthy adults.
CO larm is not a substitute for proper maintenance of home
appliances.
To help prevent CO problems and reduce the risk of CO poisoning:
• Clean chimneys and flues yearly. Keep them free of debris, leaves,
and nests for proper air flow. lso, have a professional check for
rust and corrosion, cracks, or separations. These conditions can
prevent proper air movement and cause backdrafting. Never "cap"
or cover a chimney in any way that would block air flow.
• Test and maintain all fuel-burning equipment annually. Many
local gas or oil companies and HV C companies offer appliance
inspections for a nominal fee.
• Make regular visual inspections of all fuel-burning appliances.
Check appliances for excessive rust and scaling. lso check the
flame on the burner and pilot lights. The flame should be blue.
yellow flame means fuel is not being burned completely and CO
may be present. Keep the blower door on the furnace closed. Use
vents or fans when they are available on all fuel-burning appliances.
Make sure appliances are vented to the outside. Do not grill or
barbecue indoors, or in garages or on screen porches.
• Check for exhaust backflow from CO sources. Check the draft
hood on an operating furnace for a backdraft. Look for cracks on
furnace heat exchangers.
• Check the house or garage on the other side of shared wall.
• Keep windows and doors open slightly. If you suspect that CO is
escaping into your home, open a window or a door. Opening
windows and doors can significantly decrease CO levels.
In addition, familiarize yourself with all enclosed materials. Read
this manual in its entirety, and make sure you understand what to
do if your CO larm sounds.
3 4
REGULATORY INFORMATION FOR CO ALARMS
WHAT LEVELS OF CO CAUSE AN ALARM?
Underwriters Laboratories Inc. Standard UL2034 requires residential CO Why is this important? Because you need to be warned of a potential
larms to sound when exposed to levels of CO and exposure times as CO problem while you can still react in time. In many reported cases of
described below. CO levels are measured in parts per million (ppm) of CO exposure, victims may be aware that they are not feeling well, but
CO over time (in minutes). become disoriented and can no longer react well enough to exit the
building or get help. lso, young children and pets may be the first
UL2034 Required larm Points*:
affected. The average healthy adult might not feel any symptoms when
• If the alarm is exposed to 400 ppm of CO, IT MUST L RM the CO larm sounds. However, people with cardiac or respiratory
BETWEEN 4 and 15 MINUTES problems, infants, unborn babies, pregnant mothers, or elderly people
can be more quickly and severely affected by CO. If you experience
• If the alarm is exposed to 150 ppm of CO, IT MUST L RM
even mild symptoms of CO poisoning, consult your doctor immediately!
BETWEEN 10 and 50 MINUTES.
• If the alarm is exposed to 70 ppm of CO, IT MUST L RM Standards: Underwriters Laboratories Inc. Single and Multiple Station
BETWEEN 60 and 240 MINUTES. carbon monoxide alarms UL2034.
* pproximately 10% COHb exposure at levels of 10% to 95% Relative
ccording to Underwriters Laboratories Inc. UL2034, Section 1-1.2:
Humidity (RH).
"Carbon monoxide alarms covered by these requirements are intended
to respond to the presence of carbon monoxide from sources such as,
The unit is designed not to alarm when exposed to a constant level
of 30 ppm for 30 days. but not limited to, exhaust from internal-combustion engines, abnormal
operation of fuel-fired appliances, and fireplaces. CO larms are
intended to alarm at carbon monoxide levels below those that could
CO larms are designed to alarm before there is an immediate life cause a loss of ability to react to the dangers of Carbon Monoxide
threat. Since you cannot see or smell CO, never assume it's not present. exposure." This CO larm monitors the air at the larm, and is designed
to alarm before CO levels become life threatening. This allows you
• n exposure to 100 ppm of CO for 20 minutes may not affect
precious time to leave the house and correct the problem. This is only
average, healthy adults, but after 4 hours the same level may
possible if larms are located, installed, and maintained as described in
cause headaches.
this manual.
• n exposure to 400 ppm of CO may cause headaches in average,
healthy adults after 35 minutes, but can cause death after 2 hours. Gas Detection at Typical Temperature and Humidity Ranges: The
CO larm is not formulated to detect CO levels below 30 ppm typically.
UL tested for false alarm resistance to Methane (500 ppm), Butane (300
ppm), Heptane (500 ppm), Ethyl cetate (200 ppm), Isopropyl lcohol
This CO larm measures exposure to CO over time. It alarms if CO
(200 ppm) and Carbon Dioxide (5000 ppm). Values measure gas and
levels are extremely high in a short period of time, or if CO levels reach
vapor concentrations in parts per million.
a certain minimum over a long period of time. The CO larm generally
sounds an alarm before the onset of symptoms in average, healthy
udible larm: 85 dB minimum at 10 feet (3 meters).
adults.
GENERAL LIMITATIONS OF CO ALARMS
This CO larm is intended for residential use. It is not intended for CO larms may not be heard. The alarm horn loudness meets or
use in industrial applications where Occupational Safety and Health exceeds current UL standards of 85 dB at 10 feet (3 meters). However,
dministration (OSH ) requirements for carbon monoxide detectors if the CO larm is installed outside the bedroom, it may not wake up a
must be met. sound sleeper or one who has recently used drugs or has been drinking
alcoholic beverages. This is especially true if the door is closed or only
CO alarms may not waken all individuals. If children or others do not
partly open. Even persons who are awake may not hear the alarm horn
readily waken to the sound of the CO alarm, or if there are infants or
if the sound is blocked by distance or closed doors. Noise from traffic,
family members with mobility limitations, make sure that someone is
stereo, radio, television, air conditioner, or other appliances may also
assigned to assist them in the event of an emergency.
prevent alert persons from hearing the alarm horn. This CO larm is
CO larms will not work without power. This CO larm requires a not intended for people who are hearing impaired.
continuous supply of C power. Plug into an unswitched 120V C outlet
CO larms are not a substitute for a smoke alarm. lthough fire is a
only.
source of carbon monoxide, this CO larm does not sense smoke or
CO larms for Solar or Wind Energy users and battery backup
fire. This CO larm senses CO that may be escaping unnoticed from
power systems: C powered CO larms should only be operated with
malfunctioning furnaces, appliances, or other sources. Early warning of
true or pure sine wave inverters. Operating this CO larm with most
fire requires the installation of smoke alarms.
battery-powered UPS (uninterruptible power supply) products or square
wave or "quasi sine wave" inverters will damage the larm. If you are CO larms are not a substitute for life insurance. Though these CO
not sure about your inverter or UPS type, please consult with the manu- larms warn against increasing CO levels, BRK Brands, Inc. does not
facturer to verify. warrant or imply in any way that they will protect lives from CO poisoning.
Homeowners and renters must still insure their lives.
This CO larm will not sense carbon monoxide that does not reach
the sensor. This CO larm will only sense CO at the sensor. CO may be CO larms have a limited life. lthough the CO larm and all of its
present in other areas. Doors or other obstructions may affect the rate parts have passed many stringent tests and are designed to be as
at which CO reaches the CO larm. For this reason, if bedroom doors reliable as possible, any of these parts could fail at any time. Therefore,
are usually closed at night, we recommend you install a CO larm in you must test your CO larm weekly.
each bedroom and in the hallway between them.
CO larms are not foolproof. Like all other electronic devices, CO
CO larms may not sense CO on another level of the home. For
larms have limitations. They can only detect CO that reaches their
example, a CO larm on the second level, near the bedrooms, may not
sensors. They may not give early warning to rising CO levels if the CO
sense CO in the basement. For this reason, one CO larm may not give
is coming from a remote part of the home, away from the CO larm.
adequate warning. Complete coverage is recommended. Place CO
larms on each level of the home.
TROUBLESHOOTING GUIDE
PROBLEM... THIS MEANS...
Red light is OFF. Unit will not alarm when you CO larms may not be plugged all the way in, or
press the Test/Silence button. is not receiving power.
The light flashes (RED) and the horn sounds 3 M LFUNCTION SIGN L. CO larm needs to be
"chirps" every minute. replaced.
The light flashes (RED) and the horn sounds 5 END OF LIFE SIGN L. CO larm needs to be
"chirps" every minute. replaced.
CO larm goes back into alarm 4 minutes after CO levels indicate a potentially dangerous
you press the Test/Silence button. situation.
CO larm sounds frequently even though no high The CO larm may be improperly located.
levels of CO are revealed in an investigation. Refer to "Where to Install CO larms."
If you have any questions that cannot be answered by reading this manual, call Consumer ffairs at 1-800-323-9005.
LIMITED WARRANTY
BRK Brands, Inc. ("BRK") the maker of First lert ® brand products, warrants that for a period of seven years from the date of purchase, this
product will be free from defects in material and workmanship. BRK, at its option, will repair or replace this product or any component of the
product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component.
If the product is no longer available, replacement may be made with a similar product of equal or greater value This is your exclusive warranty.
This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the original sales
receipt. Proof of purchase is required to obtain warranty performance. BRK dealers, service centers, or retail stores selling BRK products do
not have the right to alter, modify or any way change the terms and conditions of this warranty.
This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use
on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than BRK or an
authorized service center. Further, the warranty does not cover acts of God, such as fire, flood, hurricanes and tornadoes or any batteries that
are included with this unit.
BRK shall not be liable for any incidental or consequential damages caused by the breach of any express or implied warranty. Except to the
extent prohibited by applicable law, any implied warranty of merchantability or fitness for a particular purpose is limited in duration to the
duration of the above warranty. Some states, provinces, or jurisdictions do not allow the exclusion or limitation of incidental or consequential
damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights that vary from state to state, or province to province.
How to Obtain Warranty Service
Service: If service is required, do not return the product to your retailer. In order to obtain warranty service, contact the Consumer ffairs
Division at 1-800-323-9005, 7:30 M to 5:00 PM, Central Standard Time, Monday through Friday. To assist in serving you, please have the
model number and date of purchase available when calling.
For Warranty Service return to: BRK Brands, Inc., 25 Spur Drive, El Paso, TX 79906
For your records, please record:
The alarm will also provide an audible End-of-Life Signal
Date Purchased: __________Where Purchased: _______________ approximately 7 years after installation to remind you to
replace the unit.
Date Installed: ____________/____________Month/Year
The End-of-Life Signal can be silenced for up to 2 days.
Replace alarm 7 years after installation. Please write the date Do not unplug the alarm or remove the batteries until you
in the space provided: get replacement.
___________/__________Month/Year
First lert ®
5
YOU SHOULD...
Gently push unit all the way into outlet. Make
sure it is not plugged into an outlet controlled by
a switch.
Make sure unit is plugged in securely.
CO larms under warranty should be returned
to manufacturer for replacement. See "Limited
Warranty" for details.
Immediately replace the CO larm.
IF YOU RE FEELING SYMPTOMS OF CO
POISONING, EV CU TE your home and call 911
or the Fire Department. If not, press the Test/
Silence button again and keep ventilating your
home.
Relocate your larm. If frequent alarms continue,
have home rechecked for potential CO problems.
You may be experiencing an intermittent CO
problem.
is a registered trademark of the First lert Trust.
Printed in Mexico M08-0152-008 S 08/12
6