Main menu ... 13 Video menu ... 14 Color Menu ... 15 Clock Menu ... 15 4. Maintenance ... 16 5. Troubleshooting ... 16 Appendix A: Possible resolutions ... 17 Appendix B: Technical specifications ... 18 MFCD 1218 User's Guide...
1. OVERVIEW 1.1 Introduction Multi-scan capabilities Power Saving The MFCD 1218, BARCO’s full color 18” LCD display, guarantees perfect image quality in medical imaging applications. The display combines a TFT (thin film transistor) liquid crystal display panel structure and a built-in backlight with inverter for a better picture quality.
European power cord American power cord Video cable S-Video cable (S-Video and composite video (RCA)) - Optional Mounting plate with 8 screws This user manual CD-ROM containing the DICOM Optimizer and its User Manual in html format (10) MFCD 1218 User's Guide...
Page 6
The LED is off when the display is off. The LED is green when the display is on. The LED is orange when the display is in power-saving mode (stand-by) Power key (10) Push-button to release the panel from the foot MFCD 1218 User's Guide...
Step 1: Remove the panel from the foot Position one hand under the panel at the front side. Position the other hand at the rear, under the push-button with BARCO logo (10). Firmly press down the push-button (10) with one hand while carefully lifting the panel up with the other hand.
Page 8
Place the panel on the mounting plate (C). If you want to secure the panel to the mounting plate, place the panel in the frontmost notches. Please make sure that the four shafts are securely placed in the notches of the mounting plate. MFCD 1218 User's Guide...
AC input of the 12V DC adapter. Connect the 12V supply of the 12V DC adapter to the DC input (1) of the monitor. Connect the other end of the power cord to a grounded power outlet. MFCD 1218 User's Guide...
Proceed as follows: Install the CD-ROM in the CD-ROM drive. The CD-ROM starts automatically. Please follow the instructions on the screen. The CD-ROM contains user instructions about the usage of the DICOM Optimizer. MFCD 1218 User's Guide...
> > RED indicates the function is > selected and ready to be > adjusted. Blinking RED indicates OSD is in parameter adjusting mode. 48.4k MFCD 1218 User's Guide automatically after an inactivity period of 30 seconds.
When the system is changed to this mode again later on, the system will not repeat the Auto Adjust function. This function is only valid when the mode concerned is selected for the first time. MFCD 1218 User's Guide...
To save the adjustments and quit the OSD menu. Note: The bottom line of the OSD shows the input type, current resolution of the monitor and status of vertical sync. If it shows user mode, please refer to the monitor Preset mode. MFCD 1218 User's Guide...
To perform the Autobalance function, you need to select a proper test pattern before performing the function. Proceed as follows: You must have installed the Barco DICOM optimizer software. Open the Windows Control Panel. open the Display control panel. Select the Barco DICOM optimizer tab.
TFT displays. 10 or less permanently dead pixels do not make out a good case for exchanging the unit. Please contact our Customer Service Department if the number of pixel faults exceeds the above- mentioned figure. MFCD 1218 User's Guide...
37.50 43.30 31.47 35.10 37.88 48.10 46.88 53.70 49.80 74.6 48.36 56.50 60.02 VESA/CRUS 60.24 68.70 67.50 63.98 91.146 MFCD 1218 User's Guide Analog Digital VESA VESA VESA VESA VESA VESA VESA VESA VESA VESA VESA VESA VESA VESA VESA...
Mini – DIN – 6 – Connector (for S-video and composite input) DVI connector Power source 100 ~ 240 VAC Power consumption 48 watts (max.) Power saving VESA DPMS standard EPA/Energy Star compliant PnP compatibility VESA DDC 2B standards compliant MFCD 1218 User's Guide...
Page 18
SPECIFICATIONS ARE SUBJECTED TO CHANGE WITHOUT NOTICE. BARCO SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN; NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES WHATSOEVER RESULTING FROM FURNISHING, PERFORMANCE OR USE OF THIS MATERIAL. MFCD 1218 User's Guide...