Table of Contents
Related Manuals for Omega C4EIT
Summary of Contents for Omega C4EIT
- Page 1 User’ s Guide RoHS 2 Compliant Shop on line at ® ® omega.com e-mail: info@omega.com iSeries info: omega.com/specs/iseries For latest product manuals omegamanual.info Embedded Ethernet for iSeries Monitor/Controller -C4EIT/-EIT...
-
Page 3: Table Of Contents
4.5.4.1 Date and Time ..............23 4.5.5 Management................24 4.5.5.1 Management - Email SNMP..........25 4.5.5.2 Management - Alarm............26 4.5.5.2.1 Sending Txt Messages to a Cell Phone .....27 4.5.6 Security..................28 4.5.7 Device Query.................29 4.5.8 Device Setup .................30 4.5.8.1 Device Parameters -C4EIT ..........31 4.5.8.2 Device Setup -EIT ............32... - Page 4 4.5.8.3 Device Parameters -EIT..........33 4.5.9 Readings................34 4.5.9.1 Readings - Device Setpoints .........34 4.5.10 Terminal ................35 4.5.11 System .................36 4.5.12 Diagnostics .................37 4.5.12.1 Diagnostics - Serial Port ..........37 4.5.12.2 Diagnostics - Ethernet Port .........38 4.5.12.3 Diagnostics - Ping ............38 Part 5: Specifications .................... 39 Part 6: Factory Preset Values ................41 Part 7: Approvals Information ................42 Appendix A...
- Page 5 Figure 4.13 iServer SECURITY Page ..............28 Figure 4.14 iServer DEVICE QUERY Page ............29 Figure 4.15 iServer DEVICE SETUP Page – RS485 (-C4EIT) ......30 Figure 4.16 iServer DEVICE PARAMETERS Page (-C4EIT ......31 Figure 4.17 iServer DEVICE SETUP Page (-EIT) ..........32 Figure 4.18 iServer DEVICE PARAMETERS Page (-EIT)........33...
- Page 6 LIST OF TABLES: Table 2.1 Rear Panel Annunciators..............5 Table 2.2 Data Transmission Characteristics RS485 ........5 Table 2.3 Half Duplex Hookup .................6 Table 4.1 Command Prefix Letters ..............11 Table 4.2 Command Formats.................11 Table K-1 iLog Excel Applications ..............66 Table K-2 iLog Error Messages..............67...
- Page 7 NOTES, WARNINGS and CAUTIONS Information that is especially important to note is identified by following labels: • NOTE • WARNING or CAUTION • IMPORTANT • TIP NOTE: Provides you with information that is important to successfully setup and use the iServer. CAUTION or WARNING: Tells you about the risk of electrical shock.
-
Page 8: Part 1: Introduction
PART 1 INTRODUCTION 1.1 Safety and EMC Considerations This device is marked with the international caution symbol. It is important to read this manual before installing or commissioning this device as it contains important information relating to Safety and EMC (Electromagnetic Compatibility). -
Page 9: Description
1.2 Description The iServer is an Ethernet Server designed to connect devices with serial interfaces to the Ethernet network using the TCP/IP protocol. It contains Ethernet and RS232 or RS485 interfaces. The standard features include: • Use standard Web Browser, TCP connection, HTTPget DOS program or Telnet Simulation, for network connectivity. -
Page 10: Part 2: Hardware
PART 2 HARDWARE 2.1 Physical Characteristics and Mounting For physical dimensions and installation instructions see Quickstart and Manual for iSeries monitor/controller. 2.2 Rear Panel of iSeries Meter with Embedded Ethernet Server Figure 2.1 Rear Panel View of i16, i8 and iDR Series Meters with Embedded Ethernet Server... -
Page 11: Rear Panel Of Iseries Meter With Embedded Ethernet Server
The iSeries controller/monitor with Embedded Ethernet Server option supports only RS485/422 interfaces to slave instruments with RS485 interfaces (ex: i833-C24). This allows the use of one TCP/IP address assigned to the master unit (-C4EIT) to communicate with multiple slave units (-C24). See Figure 2.3. -
Page 12: Wiring Rs485 Interface
2.3.1 Wiring Master/Slave Units via RS485 Interface RS485 interface uses a two-wire communication system (one for transmitting and one for receiving) plus a common wire to connect to the shield of the cable. It is recommended to use a shielded cable with one twisted pair. Use of twisted pair and shield will significantly improve noise immunity. -
Page 13: Network Communication Interfaces
2.4 Network Communication Interfaces 2.4.1 10BASE-T RJ-45 Pinout The 10BASE-T Ethernet network system is used in the iServer for network connectivity. The 10 Mbps twisted-pair Ethernet system operates over two pairs of wires. One pair is used for receiving data signals and the other pair is used for transmitting data signals. This means that four pins of the eight-pin connector are used. -
Page 14: Part 3: Network Configuration
PART 3 NETWORK CONFIGURATION 3.1 Network Protocols The iServer can be connected to an Ethernet network using standard IP protocols including TCP, UDP, SNMP, SMTP, ARP, HTTP (WEB server), DHCP, DNS, Telnet, and Modbus TCP/IP. 3.2 Ethernet (MAC) Address MAC (Media Access Control) address is your computer's unique hardware number. When you're connected to the LAN from your computer, a correspondence table relates your IP address to your computer's physical (MAC) address. -
Page 15: Dhcp
3.3 DHCP DHCP, Dynamic Host Configuration Protocol, enables computers and devices to extract their IP configurations from a server (DHCP server). If DHCP is enabled on your iServer, as soon as the iServer is connected to the network, there is an exchange of information between the iServer and the DHCP server. -
Page 16: Tcp Port (Socket) Number
3.6 TCP Port (Socket) Number All TCP connections are defined by an IP address and a port number. A port number is an internal address that provides a TCP/IP interface between an application software on a computer and a device on the network. There are three default TCP port (socket) numbers assigned to the iServer: 1. -
Page 17: Part 4: Operations
PART 4 OPERATIONS This iServer can be configured in several ways, depending on user’s preference and network setup. It can be configured using a Web browser like Chrome, Internet Explorer, or Firefox to access its Web server. It can also be configured using a TCP connection to port 2002 using a command line interface. - Page 18 Where: "*" is the selected Recognition Character. You may select any ASCII table symbol from "!" (HEX address "21") to the right-hand brace (HEX "7D") except for the caret "^", "A", "E", which are reserved for bus format request. "ccc" stands for the hex-ASCII Command Class letter (one of eleven given in Table 4.1), followed by the two hex-ASCII Command Suffix characters identifying the meter data, features, or menu items to which the command is directed.
-
Page 19: Default Ip Address
4.4 Default IP Address The iServer is shipped with a default IP address of 192.168.1.200 and Subnet Mask of 255.255.255.0. If you are going to use a Web browser or Telnet program to access the iServer using its default IP address, make sure that the PC from which you’re establishing the connection has an IP address that is in the same range as the iServer’s IP address (192.168.1.x, where x can be any number from 1 to 254). -
Page 20: Access And Configuration Using A Web Browser
4.5 Access and Configuration Using a Web Browser • Start your web browser. In the URL field, type http://192.168.1.200 (iServer’s default IP address) • • The iServer will display the LOGIN page, as shown below. Figure 4.2 iServer LOGIN Page In order to access iServer’s web pages, users may be prompted for a password. -
Page 21: Overview
4.5.1 Overview Once the LOGIN password is entered, the OVERVIEW page will appear which provides a summary of important parameters within the iServer. All the fields are read-only. Figure 4.4a iServer -C4EIT OVERVIEW Page Figure 4.4b iServer -EIT OVERVIEW Page... -
Page 22: Network
4.5.2 Network This page provides configurations for the Ethernet interface and TCP/IP parameters. Fields are described below. Figure 4.5 iServer NETWORK Page DHCP – If the box is checked the iServer will dynamically request an IP address, a subnet mask, a gateway address, and a DNS address from the DHCP server. By default the DHCP option is disabled. - Page 23 4.5.2 Network (continued) Subnet Mask – A 32-bit number that is used to determine which part of the IP address is the network portion and which part is the host portion. When DHCP is enabled this field will be dimmed. The iServer’s default Subnet Mask is 255.255.255.0.
-
Page 24: Serial (Rs485 Serial Port)
4.10). Fields are described below. The RS485 Service Port Tab as shown in Figure 4.6 will appear only for option C4EIT. For the iSeries EIT option the following parameters: 9600,O,7,1,none are fixed and the device must be set to these parameters. -
Page 25: Network-To-Serial
4.5.3.2 Network-to-Serial For units with -EIT option the RS485 Serial Port tab will not be part of web page. Figure 4.7 iServer SERIAL Page – Network to Serial Local Port – This is the port number assigned to the iServer’s serial port for the purpose of TCP, UDP, or ModbusTCP connection. -
Page 26: Packing Techniques
4.5.3.3 Packing Techniques Figure 4.8 iServer SERIAL Page – Packing Techniques End Character – When this hexadecimal character is received by the iServer on its serial port, the iServer will forward the buffered serial data to the Ethernet. The default value is D, which means the iServer requires no End Character to forward the data to the network. -
Page 27: Multi-Host Connection
4.5.3.3 Packing Techniques (continued) Packet Length – If the received data length (in bytes) matches the entered value, the data will be sent out to the network. The data length of up to 1024 bytes can be entered. Enter 0 if you don’t need to limit the length. The default is 0. Inactivity Timeout –... -
Page 28: Configuration
4.5.3.4 Multi-host Connection (Continued) Connection Type – The options are Disable, Simultaneous, and Sequential. The iServer can send the received serial data to multiple network hosts Simultaneously or Sequentially. In Simultaneous mode, the received serial data will be transmitted to all the network nodes that are indicated in the host table (using TCP or UDP protocol depending on which protocol is selected under the NETWORK page). -
Page 29: Date And Time
4.5.4.1 Date and Time Current Date – This field indicates the iServer’s real time clock date. The format is yyyy/mm/dd. When there is no date defined, the iServer will be defaulted to 2099/01/01 and be shown in red to alert you that it has not yet been set. Current Time –... -
Page 30: Management
4.5.5 Management This page provides the configuration of the iServer’s email, SNMP and alarm settings. SNMP (Simple Network Management Protocol) is a protocol used by network management systems to communicate with network devices that respond to SNMP connections for the purpose of problem detections and corrections (see Figures 4.11 and 4.12). -
Page 31: Management - Email Snmp
4.5.5.1 Management - Email SNMP SNMP Service – This option is used to enable the SNMP service. The default is unchecked. SNMP Community – Every SNMP communication takes place using a community string. It’s configurable to either public or private. Public is the default. Contact –... -
Page 32: Management - Alarm
4.5.5.2 Management - Alarm Figure 4.12 iServer MANAGEMENT Page – Alarm Power Reset – Email – This option enables iServer to send an email when it is rebooted. Power Reset – Trap – This option enables iServer to send a trap when it is rebooted. -
Page 33: Sending Txt Messages To A Cell Phone
4.5.5.2.1 Sending Txt Messages to a Cell Phone To send an alarm as a text message to your cell phone you need to enter the email address that is associated with your cell phone number. For example: 7145551212@xxxx.xxx where 714-555-1212 is the cell phone number and xxxx.xxx is the domain name for the telecomm provider. -
Page 34: Security
4.5.6 Security This page provides security and access settings for the iServer. Administrator password (default is 00000000) is required to access the SECURITY page. Fields are described below. Figure 4.13 iServer SECURITY Page Login Password – To access the iServer’s web server this password is required. The password length can be up to 16 alphanumeric case-sensitive characters. -
Page 35: Device Query
4.5.6 Security (continued) Telnet Console Access – If checked, Telnet to the iServer’s port 2002 is allowed. The default is checked. The password for the Telnet Console Access is the same as the Administrator Password. Web Server Access – If checked, a web browser can be used to connect to the iServer’s web server. -
Page 36: Device Setup
On this page there is a Device Number column (No), which has numbers from 1 to 8. These numbers are links to the parameters of each device; click on them to enter the device name, address, command and unit. Figure 4.15 iServer DEVICE SETUP Page – RS485 (-C4EIT) -
Page 37: Device Parameters -C4Eit
Device name - This field allows you to enter the device name and can take up to eight alphanumeric characters. Default is blank. Device address - This column only appears for RS485 (-C4EIT). Device address or ID is in HEX format. See Appendix D for conversion. Default is blank. -
Page 38: Device Setup -Eit
4.5.8.2 Device Setup -EIT This option allows the users to add up to eight device labels, commands and a response unit. The iServer will send the entered commands on the serial port and will receive the responses from those devices. Clicking on Readings page link will show the response. -
Page 39: Device Parameters -Eit
4.5.8.3 Device Parameters -EIT After clicking on any of the numbers (1 through 8), you will be directed to the DEVICE PARAMETERS page. Device name - This field allows you to enter the device name and can take up to eight alphanumeric characters. -
Page 40: Readings
READINGS page allows you to monitor the response back from the serial device. Y ou can access the setpoints by clicking on the numbers 1 to 8. Figure 4.19 iServer READINGS Page (-C4EIT) Auto Update - To change the time interval of the page refresh, enter the amount of seconds in the box. -
Page 41: Terminal
4.5.10 Terminal On this page you can send and receive data to and from the serial device. Simply, type the command in the white area and as you type the characters, the characters will be transmitted out from the serial port of the iServer. If you want to send the whole command as a word, simple paste the word in the same area. -
Page 42: System
4.5.11 System This page provides various options to reboot, restore defaults, upgrade firmware and download/upload configuration for the iServer. Fields are described below. Figure 4.22 iServer SYSTEM Page Reboot – Clicking on OK button will reboot the iServer. After rebooting, please wait 15 seconds before reconnecting. Defaults –... -
Page 43: Diagnostics
Download Config – Using this option you can download the configuration file that contains all the settings stored in the iServer and use it as a reference. Upload Config – Using this option you can upload the saved configuration file to the iServer. -
Page 44: Diagnostics - Ethernet Port
4.5.12.2 Diagnostics - Ethernet Port This section of the webpage provides information about Ethernet packets sent/received by the iServer. TCP – Received – TCP packets received by the iServer. TCP – Transmitted – TCP packets transmitted by the iServer. UDP – Received – UDP packets received by the iServer. UDP –... -
Page 45: Part 5: Specifications
PART 5 SPECIFICATIONS Serial Interface (-C4EIT) Interface: RS422 or RS485 (2-wire) Connector: Terminal Block Plugs Serial Data Rates: 300 to 460,800 bps* *iSeries Controller max is 19,200 bps Characters: 5, 6, 7, or 8 data bits Parity: odd, even, or none... - Page 46 External Fuse Required: Time-Delay, UL 248-14 listed: 100 mA/250 V 400 mA/250 V (Low Voltage/Power Option) Time-Lag, IEC 127-3 recognized: 100 mA/250 V 400 mA/250 V (Low Voltage/Power Option) Environmental Conditions: • All models: 0 to 55°C (32 to 131°F), 90% RH non-condensing •...
-
Page 47: Part 6: Factory Preset Values
PART 6 FACTORY PRESET VALUES PRESET PARAMETERS FACTORY DEFAULTS Network Interface: DHCP Disabled IP Address 192.168.1.200 Subnet Mask 255.255.255.0 Gateway Address 0.0.0.0 DNS Address 0.0.0.0 Host name eitxxxx (x = last 4 digits from the MAC address) Protocol Web Server Port Ethernet Port 10 Mbps, half Serial Interface:... -
Page 48: Part 7: Approvals Information
PART 7 APPROVALS INFORMATION 7.1 APPROVALS INFORMATION This product conforms to the EMC directive 89/336/EEC amended by 93/68/EEC, and with the European Low Voltage Directive 72/23/EEC. Electrical Safety EN61010-1:2001 Safety requirements for electrical equipment for measurement, control and laboratory. Double Insulation Pollution Degree 2 Dielectric withstand Test per 1 min •... -
Page 49: Appendix A Glossary
Appendix A GLOSSARY User of this manual should be familiar with following definitions: ARP (Address Resolution Protocol) is a protocol for mapping an Internet Protocol address (IP address) to a physical machine address that is recognized in the local network. For example, the IP address in use today is an address that is 32-bits long. -
Page 50: Appendix Bip Address
Appendix B IP Address An IP address is a unique 32-bit address assigned to a computer and includes: • A network ID number identifying a network. • A host ID number identifying a computer on the network. All IP addresses have been divided into three smaller groups (classes) A, B and C •... -
Page 51: Appendix Cip Netmask
Appendix C IP Netmask IP Netmask or Subnet Mask is a 32-bit pattern of ones and zeros used to determine network portion of an IP address from the host portion of the IP address. Subnet mask is a network ID that is created by borrowing bits from host portion of IP address and using them as part of a network ID. -
Page 52: Appendix Dascii Chart
Appendix D ASCII Chart ASCII Binary ASCII Binary Char No Parity Char No parity 00000000 01000000 00000001 01000000 00000010 01000010 00000011 01000011 00000100 01000100 00000101 01000101 00000110 01000110 00000111 01000111 00001000 01001000 00001001 01001001 00001010 01001010 00001011 01001011 00001100 01001100 00001101 01001101 00001110... -
Page 53: Ascii Chart Control Codes
Appendix D ASCII Chart Continuation 00101111 01101111 00110000 01110000 00110001 01110001 00110010 01110010 00110011 01110011 00110100 01110100 00110101 01110101 00110110 01110110 00110111 01110111 00111000 01111000 00111001 01111001 00111010 01111010 00111011 01111011 < 00111100 01111100 00111101 01111101 > 00111110 01111110 00111111 01111111 ASCII Control Codes ASCII Dec Hex Ctrl Key... -
Page 54: Appendix E Iconnect Software
Appendix E iConnect Software The iServer may also be assigned an IP Address by using the iConnect software. Download the iConnect software from the website listed in this manual. Install iConnect software on a networked PC. This software is compatible with Windows 95, 98, NT, 2000, and XP. -
Page 55: Figure E-2 Accessing The Iserver's Home Page
Appendix E iConnect Software (continued) d) To access the iServer for Configuration: Click on the “View Webpage” button, you will access the iServer’s home page, as shown below. Refer to Section 4.4 for more details. Figure E-2 Accessing the iServer’s HOME Page... - Page 56 C:\iServer\httpget>httpget –r –S "*01X01\r" 192.168.1.200:1000 where: –r –S are parameters needed for the command string is device address (in hex format) for RS485 (-C4EIT) communication interface (skip for embedded ethernet (-EIT)) read measurement data value (iSeries protocol) is the carriage return termination character 192.168.1.200...
-
Page 57: Appendix Fhttpget Program
Appendix F HTTPget Program (continued) C:\iServer>httpget -r -S "*02X01\r" 192.168.1.200:2000 02X01263.1 C:\iServer> See the data on the console if the disconnect checkbox is “checked”. Figure F-1 iServer SERIAL Page – Network to Serial If the “Disconnect After Data Sent” is unchecked, the cursor will stay with no line feed C:\iServer>httpget -r -S "*02X01\r"... -
Page 58: Appendix Garp Program
Appendix G ARP Program ARP is the Internet layer protocol responsible for matching or obtaining the MAC (hardware) address that corresponds to a particular IP address. The ARP command allows the user to view the current contents of the ARP cache of the local computer (residing on the same network) or remote computer (residing on the different network) through a router. -
Page 59: Appendix H Telnet Setup
Appendix H Telnet Setup Telnet stands for Telecommunications Network, it is a protocol that provides a way for users (or clients) to connect to computers (or servers) on a network, whether in the next building or across the other side of the world. You can open a Telnet session using other terminal emulation programs like Tera Term Pro (downloadable from the internet), which is a free software for MS- Windows. - Page 60 Appendix H Telnet Setup (continued) Is the configuration command, used to set a new setting (see the example in Figure I-3) RESET Following with a return character, it will recycle the Power on the iServer. FACTORY Following with a return character, it will set the iServer to it’s factory default settings.
-
Page 61: Figure H-3 Telnet Setup - Iserver Help Page
Appendix H Telnet Setup (continued) | GW | Gateway | DN | DNS server address | LP | Login password | 0-16 Alphanumeric chars | SP | Admin password | 0-16 Alphanumeric chars | PP | Local port password | 0-16 Alphanumeric chars | TC | Telnet console access | 0-Disable, 1-Enable... -
Page 62: Appendix I Remote Access (Tunneling)
TCP/IP protocol. Therefore, the connected serial devices to iServer’s can also communicate with each other back and forth over these networks. This characteristic is called Tunneling and it’s illustrated in Figures I.1 and I.2. Figure I-1a Serial Tunneling - iSeries -C4EIT Figure I-1b Serial Tunneling - iSeries -EIT... -
Page 63: Figure I-2 Device-To-Device Communication
In order to use this Tunneling feature, some settings are required within the local and remote iServer’s. I-1 Remote iSeries -EIT/-C4EIT It’s recommended to configure the Remote iServer and have it up and running before the Local iServer is configured. - Page 64 10 seconds. 9. Click on Save button for the changes to take place. When setting the iSeries -EIT/-C4EIT as a Remote iServer, reboot the unit for the settings to take place. When setting the iSeries -EIT/-C4EIT as a Local iServer, only the iSeries -C4EIT has RS485 serial connection.
-
Page 65: Figure 1-3 Serial - Multi-Host Connection (-C4Eit)
Appendix I Remote Access (Tunneling) (continued) I-2 Local iSeries -EIT/-C4EIT (continued) Figure I-3 SERIAL - Multi-Host Connection (-C4EIT) - Page 66 Appendix I Remote Access (Tunneling) (continued) I-3 Tunneling Troubleshooting Using the original serial cable, please confirm valid communication between the serial device and its application software on the PC with no iServers in between (direct serial connection). Otherwise, reset the power, first on the remote iServer and then on the local iServer and recheck for Connection type drop down menu as simultaneous.
-
Page 67: Appendix J Iport
Appendix J iPORT J-1 iPORT, COM Port Redirector To obtain the iPORT software (iPORT.exe file) please use the phone number, as listed on the cover of this manual, to contact the Sales Department nearest you. To install the iPORT application, simply double-click on the iPORT.exe file and follow the installation steps. -
Page 68: Figure J-2A Redirect Serial Connection
Appendix J iPORT (continued) J-2 iPORT Overview (continued) This connection redirection is totally transparent to the serial device and its application software. Once the connection is up from the PC to the serial device, the data is transmitted across the Ethernet network to the serial device and back from the serial device to the PC, all through the iServer and the iPORT. -
Page 69: Figure J-3 Iport Main Window
Appendix J iPORT (continued) J-3 iPORT Configurations (continued) 192.168.1.200 5000 2000 Figure J-3 iPORT Main Window Figure J-4 COM Port Window iServer IP Address – This is the IP address of the iServer that is connected to the serial device on one end and attached to the Ethernet LAN on the other end. The iServer’s default IP address is 192.168.1.200, which can be changed to fit your network IP address range (see Section 4). - Page 70 Appendix J iPORT (continued) J-3 iPORT Configurations (continued) Activate – If this box is checked, the selected COM port will be available for network connection. If it is unchecked, the selected COM port will be in sleep mode. Timeout – This is the amount of time (in milliseconds) in which the iPORT keeps the application software waiting before the device response is arrived.
-
Page 71: Appendix K Ilog Software
Appendix K iLog Software The iLog Software can only be used with our brand of instruments. For complete information of how to use the iLog software, click on the Help menu of the main window. This is an Excel application software that can log values from the serial device over the local network (Ethernet) or the internet. -
Page 72: Table K-1 Ilog Excel Applications
Appendix K iLog Software (continued) Table K-1 iLog Excel Applications The iLog application actually consists of several Excel files, though most supported devices can be accessed by the main iLog program. The main program is listed as "iLog", plus a version number, under the Start Menu program links (those links available by clicking the Start button on the Windows taskbar). -
Page 73: Table K-2 Ilog Error Messages
Appendix K iLog Software (continued) The iLog Software can only be used with our brand of instruments. Table K-2 iLog Error Messages Error # Description Note -8003 User stopped logging readings. -10005 Failed to find the iServer. Ethernet cable is disconnected, iServer is powered off, connections across the firewall require longer “connection to socket time out”... - Page 74 NOTES ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________...
- Page 75 NOTES ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________...
- Page 76 NOTES ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________...
- Page 77 NOTES ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________...
- Page 78 NOTES ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________...
- Page 79 WARRANTY/DISCLAIMER OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of one (1) year from the date of purchase. In addition to OMEGA’s standard warranty period, OMEGA Engineering will extend the warranty period for four (4) additional year if the warranty card enclosed with each instrument is returned to OMEGA.
- Page 80 Where Do I Find Everything I Need for Process Measurement and Control? OMEGA…Of Course! Shop on line at omega.com TEMPERATURE R Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies R Wire: Thermocouple, RTD & Thermistor R Calibrators & Ice Point References R Recorders, Controllers &...