Horizon Fitness FCJJ-25 i-H2GO User Manual

USER MANUAL
Works with iPhone, iPad and iPod Touch with iOS 4.3+
FCJJ-25
Parts List section
C6
C7
C8
i-H2GO car
C4
C5
C1
C9
C2
C3
R1
R2 R7
R8
R3
R9
R10
R4
R11
R5
R6
Refueling Station
USB Cable Syringe with Tube
S1
Solar Panel
S2
S3
C1 Hydrogen Fuel Tank R1 Bubble Outlet S1 Solar Power Plant Accessary
C2 Hydrogen Balloon R2 Water Tank S2 Hinge Tilt with +/- 45 Degrees
C3 Car Pairing L.E.D. R3 Water Inlet S3 Power Output Plug
C4 Purge Valve R4 Electrolyzer
C5 Female Input Valve R5 Hydrogen Hose
C6 Rubber Tires R6 Base
C7 Fuel Cell Ventilation Holes R7 Plunger
C8 Hydrogen Fuel Cell R8 Gas Window Marking
C9 ON/OFF WARM-UP Switch R9 Hydrogen Storage Tank
R10 Water Window
R11 Rubber Cap
R12 Hydrogen Male Output Valve
R13 ON/OFF Switch
R14 DC Input Jack
Download the i-H2GO APP
on your handset or tablet
OR
1. Download iTunes from www.apple.com. 1. Log on to APP STORE.
2. Search for "i-H2GO" and download it
2. Install iTunes on your computer.
to your iPhone or iPad.
3. Open iTunes and log on to APP STORE.
3. Install i-H2GO to your iPhone or iPad.
4. Search for "i-H2GO" and download it
to your computer.
5. Install i-H2GO to your iPhone or iPad
Just 8 steps and you are ready to i-H2GO!
You must complete all 8 steps for your car to work correctly.
1. CHARGING THE REFUELING STATION
Make sure the refueling station is switched "OFF" when charging. Even if your station
produces hydrogen immediately, you must charge it until the
LED on the right side of the station turns green.
10 - 16 HRS
SOLAR CHARGING: The refueling station can be fully
recharged using the included Solar Power plant
(charge time is 10 hours minimum in direct strong
sunlight). 16 hours is preferred for ultimate
performance - it is recommended to recharge any
time the unit is unused. The refueling station is
fully charged when the right LED light turns green.
Or USB CHARGING: It will take 5-6 hours to fully
charge the refueling station before use.
It is recommended to recharge the refueling station any time the unit is not used.
The refueling station is fully charged when the right LED light turns green.
Note: Some computers do not charge the station in the sleeping or off mode. The
refueling station should be in the "OFF" position when being charged. To protect the
refueling station DO NOT use the station while you are charging it. When charging you
can see the right LED is red. Charging is complete when this light turns green and then
you can unplug and use the refueling station. A fully charged station should fill up the car
about 10 times.
i-H2GO_UM_EN_V1.1
2. ADD WATER
Carefully fill with purified/distilled water
"Bubble Outlet". Even clean tap water will reduce the lifetime of
the refueling station. Avoid over-filling.
Note: Purified/distilled water must be used or else you
will damage the refueling station.
3. PRODUCE HYDROGEN
Switch the refueling station to "ON". You will notice 2 bright blue
LED lights, bubbles coming out from the outlet and the plunger
should be slowly rising. If this is not happening, please refer to
the note below or the trouble shooting section. When the
plunger stops rising and there are no more bubbles, the tank is
full and the electrolysis process stops automatically.
Note: During hydrogen production, bubbles should be
continuously coming out from the outlet. If there are no
bubbles coming out, and the refueling station is fully charged,
position the tip of the syringe on the outlet where the bubbles
are released from, and use the syringe to suck in some water.
R12
R13
You can add this extra water to the water tank. Repeat this step
R14
several times until you see bubbles coming out of the outlet.
4. CONNECT THE CAR TO THE REFUELING STATION
TO CHARGE THE CAPACITOR
Connect the "Hydrogen Hose" to the car's "Female
Input Valve" push lightly until it locks. The left
LED in the refueling station should flash red. When
the left LED turns from red to green, the capacitor is
fully charged.
5. PURGE THE IMPURE GAS
Check the water window on the back of the refueling
station. If there is water inside, go to step 8 to drain
water first.
If there is no water visible inside the window, proceed
directly to next step.
a. Switch the car to "OFF".
b. Press the car's purge valve for 1 second and release.
c. Push down the refueling station's plunger about 1/3
of the way slowly and carefully to fill the car's
"Hydrogen Balloon".
d. Press the car's "Purge Valve" to release impure
hydrogen until the "Hydrogen Balloon" is empty. You
must do this EVERY TIME you fill the car.
Note: The small amount of hydrogen you put in the car
Press
must be purged in order to remove the impurities from the
system. If the impurities are not purged, the i-H2GO will
either not work, be very slow, or the running time will be
reduced.
Release
6. FILL THE CAR'S TANK WITH HYDROGEN
a. Slowly and carefully push the plunger all the way
down to fill the car's fuel tank with the remaining
hydrogen.
b. Be sure the left LED light in the refueling station turns
green before going to "C".
6
c. Disconnect the "Hydrogen Hose" from the "Female
Input Valve" – the car's tank is full of hydrogen but now
it needs to be warmed up! Be careful, do not touch the
"Purge Valve" while disconnecting the car or you will
5-6 HRS
purge the hydrogen from the tank.
d. Once the car is fully charged, the hydrogen production
will automatically start up again if the station is in the
"ON" position. Leave the station "ON" if you want to
continue to use the car.
Note: Once the left LED light turns green, which mean
the car is ready, the hydrogen production will start
again automatically.
7. WARM-UP THE CAR
to a level covering the This is a very important step for your car to operate
correctly.
a. Set the "ON/OFF/WARM UP" Switch on the
bottom of the car to the "WARM UP" position.
b. Wait until the hydrogen in the fuel tank is empty.
c. Switch "OFF" the car.
d. Wait until the plunger has finished rising and the
bubbles stop. Then complete steps 4-7 a few times.
Now your i-H2GO is warmed and ready to go.
Note: If the balloon does not empty completely, or
stops emptying, use the "Purge Valve" to release
the hydrogen.
8. DRAIN WATER FROM REFUELING STATION
Be sure to take the refueling station to a place that can
capture the water safely.
1) If the plunger is up:
a. Open "Rubber Cap" (see photo).
b. Press down the plunger all the way slowly and
carefully.
c. Replace "Rubber Cap" securely.
d. Wipe away any water.
OR
2) If the plunger is not up:
a. Open the "Rubber Cap" (see photo).
b. Lightly lift the plunger about 1/3 of the way.
c. Push the plunger down slowly.
d. Replace "Rubber Cap" securely.
e. Wipe away any water.
Note: It is recommended to remove water from the
refueling station after using 5-6 tanks of hydrogen and
when you are finished playing with your i-H2GO.
Pairing the i-H2GO with your iPhone, iPad or iPod Touch
Pairing the i-H2GO for the first time
1. Turn the ON/OFF/WARM UP Switch to "ON", you can see the blue lights in the car are flashing.
2. Go to Bluetooth in your device's Settings
3. Turn Bluetooth on, it will take a second to search for devices.
i-H2GO
4. Select i-H2GO. When prompted for a PIN code enter: 0000 and press "Pair".
i-H2O
5. Wait until you see it display "Connected". You can now exit settings and open the i-H2GO
application.
i-H2GO
NOTES: Once your car has been connected to your iPhone, you will not have to
re-connect it for further use. But if your car has been connected to another
iPhone, and you want to use your own phone to run the car, you have to
reconnect them again.
Controlling the i-H2GO
When you open the application you will see the following:
2 3
4
1 5
6
1. Throttle Control (accelerate, brake and reverse)
2. Change Control Mode
3. Speed Lock Function
4. Gyro Steering Function
5. Direction Stick (right and left)
6. Go To Instructions
SCREEN TOUCH MOTION CONTROL:
1. Moving the "Throttle control" (1) up moves the car forward.
2. Moving the "Throttle control" (1) down moves the car backward.
3. Moving the "Direction stick" (5) to the left, the car turns left.
4. Moving the "Direction stick" (5) to the right, the car turns right.
When you use the "GYRO" (4), "Speed lock" (3) to control the car, we suggest you
build up speed slowly and carefully.
GYRO CONTROL
1. Tap the "GYRO steering function" (4).
2. To turn the car left, tilt your device to the left.
3. To turn the car right, tilt your device to the right.
SPEED LOCK CONTROL
1. Touch the "Speed lock function" (3).
2. Set the desired speed using the "Throttle control" (1) by moving it forward or
backward and then release.
3. The car will run at the same speed.
CONTROL MODE 2
TAP THE TO GET THE FOLLOWING INTERFACE
3
4
2
1 5
1. Left Turn Control
2. Change Control Mode
3. Throttle Control
4. Go to Instructions
5. Right Turn Control
When you use the "Throttle Control" (3) settings to control the car, we suggest
you build up speed slowly and carfully.
SCREEN TOUCH MOTION CONTROL:
1. Moving the "Throttle control" (3) up moves the car forward and the speed locks.
2. Moving the "Throttle control" (3) down moves the car backward and the speed locks.
3. Use the "Left Turn Control" (1) to move the car left.
4. Use the "Right Turn Control" (5) to move the car right.