Related Manuals for Horizon Fitness E-flite UMX Radian BNF BASIC
Summary of Contents for Horizon Fitness E-flite UMX Radian BNF BASIC
- Page 1 UMX Radian ™ ® Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni...
- Page 2 NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com or towerhobbies.com and click on the support or resources tab for this product. MEANING OF SPECIAL LANGUAGE The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product: WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage,...
-
Page 3: Table Of Contents
Box Contents Table of Contents Preflight Checklist ............. 4 Flying ................9 Assembly ................4 Post Flight Checklist ............ 10 Transmitter Setup ............. 5 Maintenance ..............10 Install the Flight Battery ............ 5 Troubleshooting .............. 11 Flight controller LED ............5 Parts List ................ -
Page 4: Preflight Checklist
Preflight Checklist Find a safe and open area. Perform control direction test. Charge the flight battery. Perform the AS3X Control Direction Test with the aircraft. Assemble the aircraft. Plan flight for flying field conditions. Install the transmitter batteries. Set a flight timer for 7 minutes. Install the flight battery. -
Page 5: Transmitter Setup
Transmitter Setup IMPORTANT: The installed receiver has been Computerized Transmitter Setup programmed for operation specifically in this aircraft. Start all transmitter programming with a blank ACRO To operate the various features of this aircraft, follow the model (perform a model reset), then name the model. table to setup your computer transmitter. -
Page 6: Binding
Binding CAUTION: Always keep hands away from the propeller. When armed, the motor will turn the propeller in response to any throttle movement. Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. -
Page 7: Control Surface Centering
Control Surface Centering Before your first flights, or in the event of a crash, check 3. If the surface is not centered, use a pair of pliers and to make sure the flight control surfaces are centered. It is carefully lengthen or shorten the pushrod by adjusting much better to do this mechanically due to the mechanical the U-shape in the pushrod. -
Page 8: As3X Control Response Test
AS3X Control Response Test This test ensures that the AS3X control system is Aircraft movement AS3X Reaction functioning properly. Assemble the aircraft and bind your transmitter to the receiver before performing this test. 1. Raise the throttle to any setting above 25%, then lower the throttle to activate AS3X technology. -
Page 9: Trimming The Aircraft
Trimming the Aircraft Adjusting Trim in Flight Direction of Drift Trim to Correct Familiarize yourself with your transmitter’s controls and the aircraft’s response before flying by performing the recommended Control Direction Test. Press the trim buttons on your transmitter to adjust how the aircraft flies. If the aircraft’s nose drifts in flight while the sticks are at neutral (centered) and the throttle is at 50% in AS3X flight mode, adjust the trim to compensate:... -
Page 10: Post Flight Checklist
Post Flight Checklist Disconnect the flight battery from the ESC. Repair or replace all damaged parts. Power OFF the transmitter. Store the flight battery apart from the aircraft and monitor the battery charge. Remove the flight battery from the aircraft. Make note of the flight conditions and flight plan results, Recharge the flight battery. -
Page 11: Troubleshooting
Troubleshooting Problem Possible Cause Solution Reset controls with throttle stick and throttle Aircraft will not Throttle stick and/or throttle trim is too high trim at lowest setting respond to throttle but responds to Ensure the plug for the motor is properly Motor is disconnected from receiver other controls installed... -
Page 12: Parts List
Parts List Recommended Parts Part Number Description Part Number Description EFLU2925 Tail Set: UMX Radian EFLB1501S25 150mAh 1S 3.7V 25C LiPo Battery EFLU2920 Main Wing: UMX Radian SPMR6650 DX6e 6CH Transmitter Only EFLU2916 Motor, Brushed: UMX Radian SPMXC1040 S44 4 Port AC/DC 1S LiPo Charger EFLU2967 Fuselage: UMX Radian Optional Parts... -
Page 13: Warranty And Service Contact Information
Inspection or Services Warranty Requirements If this Product needs to be inspected or serviced and is For Warranty consideration, you must include your original compliant in the country you live and use the Product in, sales receipt verifying the proof-of-purchase date. Provided please use the Horizon Online Service Request submission warranty conditions have been met, your Product will be process found on our website or call Horizon to obtain a... -
Page 14: Fcc Information
Supplier’s Declaration of Conformity off and on, the user is encouraged to try to correct the E-Flite UMX Radian BNF Basic (EFLU2950) interference by one or more of the following measures: This device complies with part 15 of the FCC •... - Page 15 © 2021 Horizon Hobby, LLC. E-flite, UMX, Radian, Bind-N-Fly, BNF, the Bind-N-Fly logo, SAFE, the SAFE logo, AS3X, ModelMatch, and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. US 9,056,667.