LG MU-60PZ95V Owner's Manual page 30

Set ID
Set ID
- Use this function to specify a monitor ID number.
- Refer to 'Real Data Mapping 1'. See page 32.
1. Press the MENU button and then use
G
2. Press the button and then use
3. Press the G button and then use
desired monitor ID number. The adjustment range of
4. Press the ENTER button to save.
Communication Parameters Communication Parameters
• Baud rate :9600 bps (UART)
• Data length : 8 bits
• Parity : None
* Use a crossed (reverse) cable.
Command Reference List
Command Reference List
COMMAND 1 COMMAND 2
01. Power k
02. Input Select k
03. Aspect Ratio k
04. Screen Mute k
05. Volume Mute k
06. Volume Control k
07. Contrast k
08. Brightness k
09. Color k
10. Tint k
11. Sharpness k
12. OSD Select k
13. Remote Control Lock Mode k
14. PIP/DW k
15. Split Zoom k
16. PIP Position k
17. Treble k
18. Bass k
19. Balance k
20. Color Temperature k
21. Red Adjustment k
22. Green Adjustment k
23. Blue Adjustment k
24. PIP Input Source k
25. Abnormal State k
26. ISM Method j
27. Low Power j
28. Orbiter Time Setting j
29. Orbiter Pixel Setting j
30. Picture Size j
31. Auto Config j
COM- COM-
MAND 1 MAND 2
32. Tune Command m a
33. Channel Add/Del m b
34. Key m c
30 Plasma TV
D / E button to select the
D / E button to select Set ID
F / G button to adjust Set ID
Set ID is 1 ~ 99.
• Stop bit : 1 bit
• Communication code : ASCII code
DATA
(Hexadecimal)
a 0 ~ 1
b 0 ~ 6
c 0 ~ 3
d 0 ~ 1
e 0 ~ 1
f 0 ~ 64
g 0 ~ 64
h 0 ~ 64
i 0 ~ 64
j 0 ~ 64
k 0 ~ 64
l 0 ~ 1
m 0 ~ 1
n 0 ~ 3
p 0 ~99
q 0 ~ 3
r 0 ~ 64
s 0 ~ 64
t 0 ~ 64
u 0 ~ 3
v 0 ~ 3C
w 0 ~ 3C
$ 0 ~ 3C
y 0 ~ 6
z 0 ~ a
p 0 ~ 3
q 0 ~ 1
r 1 ~ FE
s 1~9
t 0 ~14
u 1
DATA 0 DATA 1 DATA 2
(Hexadecimal) (Hexadecimal) (Hexadecimal)
01 ~ 7D 0 0
mainsub/TuneBand
0 ~ 1
Key code
SPECIAL menu.
.
to choose the
T ransmission / Receiving Protocol
T ransmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command 1]: First command to control PDP set. (j, k or m)
* [Command 2]: Second command to control PDP set.
* [Set ID]: You can adjust the set ID to choose desired monitor
ID number in Special menu. Adjustment range is 1
~ 99. When selecting Set ID '0', every connected
PDP set is controlled. Set ID is indicated as deci-
mal (1~99) on menu and as Hexa decimal
(0x0~0x63) on transmission/receiving protocol.
* [DATA]: To transmit command data.
Transmit 'FF' data to read status of command.
* [Cr]: Carriage Return
ASCII code '0x0D'
* [ ]: ASCII code 'space (0x20)'
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving normal data. At this time, if the
data is data read mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving abnormal data from non-viable
functions or communication errors.
Data 1: Illegal Code
2: Not supported function
3: Wait more time
DATA 3
(Hexadecimal)
External Control Device Setup
SPECIAL
SPECIAL
Language
Key lock
ISM Method
Low power
1
G
Set ID
Demo
OSD Rotate
Menu Prev.