Advertisement
Quick Links
P P
IONEER
IONEER
Q
U I C K
P D P - 5 0 1 H D
P D P - 5 0 1 R
P D P - 5 0 1 S - L R
1.0
C
I
HOOSE THE
NSTALLATION
2.0
S
U
D
ET
P THE
ISPLAY
3.0
M
S
OUNT THE
PEAKERS ON THE
4.0
S
D
ECURE THE
ISPLAY TO A
5.0
T
M
R
HE
EDIA
ECEIVER
6.0
T
P
D
HE
LASMA
ISPLAY
7.0
W
D
IRING
IAGRAM
8.0
O
I
PERATING
NSTRUCTIONS
9.0
T
R
C
HE
EMOTE
ONTROL
P P
LASMA
LASMA
R
E F E R E N C E
:
T T
ABLE OF
ABLE OF
S
........................................................................................... 2
ITE
&
M
R
THE
EDIA
ECEIVER
D
................................................................................ 3
ISPLAY
B
/
ASE AND
OR A
........................................................................................................... 5
.......................................................................................................... 7
................................................................................................................. 8
.................................................................................................. 10
U
............................................................................................... 11
NIT
D D
ISPLAY
ISPLAY
P
D
L A S M A
I S P L A Y
:
M
R
E D I A
E C E I V E R
S
P E A K E R S
:
C C
ONTENTS
ONTENTS
........................................................................ 2
W
.................................................................. 4
ALL
S S
YSTEM
YSTEM
M
A N U A L
P
A N E L
Advertisement
Related Manuals for Pioneer PDP-501HD
Summary of Contents for Pioneer PDP-501HD
- Page 1 IONEER IONEER LASMA LASMA ISPLAY ISPLAY YSTEM YSTEM U I C K E F E R E N C E A N U A L P D P - 5 0 1 H D L A S M A I S P L A Y A N E L P D P - 5 0 1 R E D I A...
- Page 2 (approximately 8” or more on all sides) ü Distance between the display and the media receiver does not exceed the length of the provided cable (contact your Pioneer Representative if additional distance is needed) 2. S & P THE ISPLAY...
- Page 3 Quick Start Installation Instructions 3. M OUNT THE PEAKERS ON THE ISPLAY 1) Remove the 2 screws from the hole-plugs on each side of the Display (1st and 2nd hole-plugs from the bottom) 2) Connect the brackets to the speakers (re-attach the small cushion pads if necessary) 3) Mount the speakers on the Display from the bottom bracket to the top...
- Page 4 Display 2) Affix a support bolt and cable to either securing hole on the Display (contact your Pioneer Representative for purchase information) 3) Fasten the end of the cable to a pillar or a wall (some walls may require hooks sunk into an internal support...
- Page 5 Quick Start Installation Instructions 5. T EDIA ECEIVER Media Receiver PDP-501R Stand-By Indicator The light turns red when the Power Open/Close the Front Door button is pressed and turns green Push the upper right corner to open the door. when the unit is functioning. Push and hold the front door to close.
- Page 6 VHF/UHF broadcasting antenna connect DVD or LD player input 2. Control Input Terminal 11. MUSE Input Terminal connect other Pioneer equipment and control connect MUSE LD player with a single remote control unit 3. BS-IF Input Terminal 12. Y/Pb/Pr Input Terminal...
- Page 7 Quick Start Installation Instructions 6. T LASMA ISPLAY Plasma Display PDP-501HD Stand-By Indicator Light appears red when the power button is pressed and changes to green when the unit is functional. Speaker (PDP-501S-LR) Install Left and Right Speakers Main Power Switch Turn the power ON and OFF.
-
Page 8: Wiring Diagram
Quick Start Installation Instructions 7. W IRING IAGRAM The wiring instructions for the Media Receiver, Plasma Display and the Speakers are shown below: Connect the System Cable to the Media Receiver (PDP-501R). Then, connect the short Speaker Cable to the Media Receiver. Connectors from Left to Right: A) to 8pin DIN Control Output USE 100VAC ONLY... - Page 9 Quick Start Installation Instructions Connect the System Cable to the Plasma Display (PDP-501HD). Rear side of the Plasma Display (PDP-501HD) Please refer to the drawing to locate correct terminals. Tighten screws after connecting Connectors from Left to Right: A) to Right Speaker Terminals...
- Page 10 Quick Start Installation Instructions 8. O PERATING NSTRUCTIONS To turn on the PDP-501 system, following the instructions listed below: Color of the Indicator Turn on the power in following order only Media Receiver Plasma Display Turn the power ON to the Media Receiver Flashing Yellow No Action Flashing Yellow...
- Page 11 Quick Start Installation Instructions 9. T EMOTE ONTROL Page 11...
- Page 12 Quick Start Installation Instructions • Avoid placing objects between the display and the Remote Control Unit. • As the battery is drained, the distance needed for a Remote Control Unit to function will become shorter. IR Sensor • The display radiates weak infrared rays from the screen.