Advertisement
Installing the AP
Service to all Alcatel-Lucent Networks products should be performed by
trained service personnel only.
Using the Ceiling Rail Adapter
The OAW-AP220 Series ships with two ceiling rail adapters for 9/16" and 15/16"
ceiling rails. Additional wall mount adapters amd ceiling rail adapters for other
rail styles are available as accessory kits.
Make sure the AP fits securely on the ceiling tile rail when hanging
the device from the ceiling, because poor installation could cause it
to fall onto people or equipment.
1. Pull the necessary cables through a prepared hole in the ceiling tile near
where the AP will be placed.
2. Place the adapter against the back of the AP with the adapter at an angle of
approximately 30 degrees to the tabs (see
Figure
6).
3. Twist the adapter clockwise until it snaps into place in the tabs (see
Figure 6 Attaching the Ceiling Rail Adapter
4. If necessary, connect the console cable to the console port on the back of the
AP.
5. Hold the AP next to the ceiling tile rail with the ceiling tile rail mounting slots
at approximately a 30-degree angle to the ceiling tile rail (see
Figure
sure that any cable slack is above the ceiling tile.
6. Pushing toward the ceiling tile, rotate the AP clockwise until the device clicks
into place on the ceiling tile rail.
Figure 7 Mounting the AP
7. On the OAW-AP224, install the external antennas according to the
manufacturer's instructions, and connect the antennas to the antenna
interfaces on the AP.
Connecting Required Cables
Install cables in accordance with all applicable local and national regulations and
practices.
Power Connection
The OAW-AP220 Series has a single 12V DC power jack socket to support
powering through an AC-to-DC power adapter.
If both POE and DC power are available, the AP draws power from the PoE
source.
Verifying Post-Installation Connectivity
The integrated LEDs on the AP can be used to verify that the AP is receiving
power and initializing successfully (see
Table
1). Refer to the AOS-W Quick Start
Guide for further details on verifying post-installation network connectivity.
Configuring the OAW-AP220 Series
AP Provisioning/Reprovisioning
Provisioning parameters are unique to each AP. These local AP parameters are
initially configured on the switch which are then pushed out to the AP and stored
on the AP itself. Alcatel-Lucent recommends that provisioning settings be
configured via the AOS-W Web UI only. Refer to the AOS-W User Guide for
complete details.
AP Configuration
Configuration parameters are network or switch specific and are configured and
stored on the switch. Network configuration settings are pushed out to the AP(s)
but remain stored on the switch.
Configuration settings can be configured via the AOS-W Web UI, AOS-W CLI, or
Figure
6).
Alcatel-Lucent MMS. Refer to their respective guides for further details: the AOS-
W User Guide or Alcatel-Lucent Mobility Management System User Guide.
Product Specifications
Electrical
Ethernet:
2 x 10/100/1000Base-T auto-sensing Ethernet RJ-45 Interfaces
MDI/MDX
IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab (1000Base-T)
Power over Ethernet (IEEE 802.3at compliant), 48V DC/350mA (see
pin configuration))
Power:
12 VDC power interface, supports powering through an AC-to-DC power adapter
POE support on Ethernet ports: 802.3at-compliant POE sourcing devices
If a power adapter other than the one provided by Alcatel-Lucent Networks
is used in the US or Canada, it should be cULus (NRTL) Listed, with an
output rated 12 VDC, minimum 1.25A, marked "LPS" or "Class 2," and
suitable for plugging into a standard power receptacle in the US and
Canada.
For additional specifications on this product, please refer to the data sheet. The data sheet
can be found at http://www.alcatel-lucent.com/enterprise.
7). Make
Proper Disposal of Alcatel-Lucent Equipment
For the most current information about Global Environmental Compliance and Alcatel-
Lucent products, see our website at http://www.alcatel-lucent.com/enterprise.
Waste of Electrical and Electronic Equipment
Alcatel-Lucent products at end of life are subject to separate
collection and treatment in the EU Member States, Norway, and
Switzerland and therefore are marked with the symbol shown at the
left (crossed-out wheelie bin). The treatment applied at end of life of
these products in these countries shall comply with the applicable
national laws of countries implementing Directive 2002/96EC on
Waste of Electrical and Electronic Equipment (WEEE).
China RoHS
Alcatel-Lucent products also comply with China environmental
declaration requirements and are labeled with the "EFUP 10" label shown
10
at the left.
European Union RoHS
Aruba Networks Inc., hereby, being the manufacturer of this
product, declares that all CE Marked Alcatel-Lucent, Inc. wirless
switch and access points products are manufactured in
accordance to the provisional requirements set forth in the RoHS Directive 2011/65/EC.
A copy of the Aruba Declaration of Conformity may be obtained upon request from:
Aruba Networks International Ltd.
Building 1000,
Citygate Mahon
Cork Ireland
Please include the regulatory model number located on the product's regulatory
nameplate within the request.
Safety and Regulatory Compliance
Alcatel-Lucent Networks provides a multi-language document that contains country-
specific restrictions and additional safety and regulatory information for all Alcatel-Lucent
access points. This document can be viewed or downloaded from the following location:
https://service.esd.alcatel-lucent.com
Regulatory Model Names
The following regulatory model names apply to the OAW-AP220 Series:
OAW-AP224: APIN0224
OAW-AP225: APIN0225
FCC
The device is electronically labeled and the FCC ID will be displayed via the switch WebUI
under the About menu.
RF Radiation Exposure Statement: This equipment complies with FCC
RF radiation exposure limits. This equipment should be installed and
operated with a minimum distance of 7.9 inches (20 cm) between the
radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter
must not be co-located or operating in conjunction with any other antenna
or transmitter. When operated in the 5.15 to 5.25 GHz frequency range, this
device is restricted to indoor use to reduce the potential for harmful
interference with co-channel Mobile Satellite Systems.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
FCC Class B Part 15
This device complies with Part 15 of the Federal Communications Commission (FCC)
Rules. Operation is subject to the following two conditions:
Figure 5
for
This device may not cause harmful interference.
This device must accept any interference received, including interference that may
cause undesired operation.
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
manufacturer's instructions, may cause interference harmful to radio communications.
If this equipment does cause interference, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio or TV technician for help.
Complies with the Class B limits for radio noise emissions as set out in the interference-
causing equipment standard entitled "Digital Apparatus," ICES-003 of Industry Canada.
Cet apareil numerique de la classe B respecte toutes les exigencies du Reglement sur le
materiel brouilleur du Canada.
EU Regulatory Conformance
Alcatel-Lucent, Inc., hereby declares that this APIN0224 and APIN0225 device
models are in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC. CE(!)The Declaration of Conformity made under Directive 1999/5/EC
https://service.esd.alcatel-lucent.com
is available for viewing at
OAW-AP220 Series Wireless
Access Point
Installation Guide
Contacting Alcatel-Lucent
Web Site Support
Main Site
http://www.alcatel-lucent.com/enterprise
Support Site
https://service.esd.alcatel-lucent.com
Support Email
esd.support@alcatel-lucent.com
Telephone Support
North America
1-800-995-2696
Latin America
1-877-919-9526
Europe
+33 (0) 38 855 6929
Asia Pacific
+65 6240 8484
Worldwide
1-818-878-4507
Copyright
Copyright © 2013 Alcatel-Lucent. All rights reserved.
Specifications in this manual are subject to change without notice.
Originated in the USA.
Trademarks
AOS-W, Alcatel 4308, Alcatel 4324, Alcatel 6000, Alcatel 41, Alcatel 60/61/65, Alcatel 70, and Alcatel 80 are trademarks of
Alcatel-Lucent in the United States and certain other countries.
Any other trademarks appearing in this manual are the property of their respective companies.
Legal Notice
The use of Alcatel-Lucent switching platforms and software, by all individuals or corporations, to terminate Cisco or Nortel
VPN client devices constitutes complete acceptance of liability by that individual or corporation for this action and
indemnifies, in full, Alcatel-Lucent from any and all legal actions that might be taken against it with respect to infringement
of copyright on behalf of Cisco Systems or Nortel Networks."
www.alcatel-lucent.com
26801 West Agoura Road
Calabasas, CA 91301
OAW-AP220 Series Wireless Access Point | Installation Guide
Part Number 0511414-01 | May 2013
Advertisement
