Ryobi BT300 Operator's Manual
  1. Manuals
  2. Brands
  3. Ryobi Manuals
  4. Tools
  5. BT300
  6. Operator's manual
Ryobi BT300 Operator's Manual

Ryobi BT300 Operator's Manual

Wide table kit for use with ryobi bt3000 table saw
Hide thumbs
Table of Contents

Advertisement

Quick Links

Your new Wide Table Kit has been engineered and manufactured to Ryobi's high standard for dependability, ease
of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this
product.
Thank you for buying a Ryobi accessory kit.
SAVE THIS MANUAL FOR FUTURE REFERENCE
OPERATOR'S MANUAL
WIDE TABLE KIT
4730300
FOR USE WITH RYOBI BT3000 TABLE SAW
LUMBER NOT INCLUDED WITH THIS KIT
TABLE SAW AND STAND NOT INCLUDED WITH THIS KIT
WIDE TABLE KIT SHOWN
ATTACHED TO BT3000 TABLE SAW

Advertisement

Table of Contents
loading

Related Manuals for Ryobi BT300

Summary of Contents for Ryobi BT300

  • Page 1 Your new Wide Table Kit has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product.

  • Page 2: Table Of Contents

     DO NOT USE THIS PRODUCT WITH OTHER EQUIP- MENT or for other purposes.  ALWAYS DISCONNECT THE SAW FROM THE POWER SUPPLY BEFORE ASSEMBLING THIS KIT. Make sure the switch is off when reconnecting the saw to a power supply. TABLE OF CONTENTS INTRODUCTION...

  • Page 3: Symbols

    BT3000 table saw. All you have to supply is the lumber required for table tops and table legs, plus the wood screws, nails, bolts, etc.

  • Page 4: Loose Parts

    Table Bracket...8 Connector...4 Front Extension Rail ...1 Square Head Bolt (1/4-20 x 1/2 in.)...4 Hex Nut (1/4-20)...4 T-Nut...12 Washer (5/16 in.) ...12 FRONT EXTENSION RAIL CONNECTOR TABLE BRACKET WOOD SCREW #2 PHILLIPS SCREWDRIVER LOOSE PARTS Hex Bolt (5/16-18 x 1/2 in.)...10 Wood Screw (#10 x 5/8 in.

  • Page 5: Assembly

    Place two T-nuts in matching channels of front extension rail.  Connect bottom T-nut to connector on front rail of your saw and secure with a washer (5/16 in.) and a hex bolt (5/16 in. x 1/2 in.). Finger tighten only.
  • Page 6  Place table top in desired position on table brackets and adjust table brackets as needed. NOTE: End of table top closest to saw will rest on lip of accessory table. See Figure 6.  Tighten the four table bracket bolts securely.
  • Page 7 See Figure 8. Table legs can be made from either 2 x 4s or by purchasing a Ryobi Leg Set, #4730305, depending upon the application in which your saw is being used. For example, if your saw is being used in a permanent application you may want to use 2 x 4s which will be more sturdy and provide extra stability.
  • Page 8 Construct them similar to methods explained for making table legs for auxiliary extension table. Either 2 x 4s or Ryobi Leg Set, # 4730305 can be used. A piece of 2 x 4 for securing table legs would need to be mounted on bottom of rear extension table.

  • Page 9: Parts Ordering / Service

    RYOBI WIDE TABLE KIT NO. 4730300 Now that you have purchased your Wide Table Kit, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all pertinent facts when you call or visit.
  • Page 10 Ryobi Authorized Service Center.Be sure to provide all pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest Ryobi Authorized Service Center.You can also check our web site at www.ryobitools.com for a complete list of Authorized Service Centers.

This manual is also suitable for:

4730300

Table of Contents