Rs-232C Commands - Runco CinemaWall CW-43MC Owner's Operating Manual

RS-232C Commands

How to read this table:
• RS-232C Adjustment Validity: Indicates whether or not the RS-232 adjustment mode can be used.
• Normal Validity:
• Numerical Direct Validity:
○ or ●
: Valid
Command
Name
A
AJN -
AJY ADJUST: ON
AMN AUDIO MUTING: OFF
AMY AUDIO MUTING: ON
AST AUTO SET UP MODE
B
BHI B GAIN
BLW B OFFSET
BRA BAUD RATE: #####-232C
BRAS01 BAUD RATE: 1200-232C
BRAS02 BAUD RATE: 2400-232C
BRAS03 BAUD RATE: 4800-232C
BRAS04 BAUD RATE: 9600-232C
BRAS05 BAUD RATE: 19200-232C
BRAS06 BAUD RATE: 38400-232C
BRT BRIGHTNESS: ***
BSL B SIDEBAR ADJ. LEVEL
C
CFR FREQ. ADJ.: ***
CGB C. DETAIL BLUE: ***
CGC C. DETAIL CYAN: ***
CGG C. DETAIL GREEN: ***
CGM C. DETAIL MAGENTA: ***
CGR C. DETAIL RED: ***
CGY C. DETAIL YELLOW: ***
CLS COLOR SYSTEM: #####
CLSS01 COLOR SYSTEM: AUTO
CLSS02 COLOR SYSTEM: NTSC
CLSS03 COLOR SYSTEM: PAL
CLSS04 COLOR SYSTEM: SECAM
CLSS05 COLOR SYSTEM: 4.43NTSC
CLSS06 COLOR SYSTEM: PAL M
CLSS07 COLOR SYSTEM: PAL N
CM1 NORMAL
CM2 ISF
CNT CONTRAST: ***
COF COLOR OFF: ********
COFS00 COLOR OFF: DISABLE
COFS01 COLOR OFF: ENABLE
COL COLOR: ***
CPH PHASE ADJ.: ***
Indicates whether or not the normal-operation mode can be used
When a number (3-digit number) is attached to the end of a command, the command can
directly set that adjustment value.
No Mark: Invalid
Full Name RS-232C
Adjustment
Validity
●
●
●
○
○
●
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
●
○
○
○
○
○
○
○
○
○
○
●
○
○
○
○
●
NOTE:
Normal Numerical
Validity Direct
Validity
Terminates the RS-232C installer adjustment mode.
● Starts the RS-232C installer adjustment mode.
● Turns audio mute OFF.
● Turns audio mute ON.
○ Executes AUTO SETUP.
○ Adjusts BLUE GAIN HIGH-LIGHT.
○ Adjusts BLUE OFFSET LOW-LIGHT.
Displays the current baud rate.
Sets the UART setting to 232C (1200bps).
Sets the UART setting to 232C (2400bps).
Sets the UART setting to 232C (4800bps).
Sets the UART setting to 232C (9600bps).
Sets the UART setting to 232C (19200bps).
Sets the UART setting to 232C (38400bps).
○ Adjusts brightness.
○ Adjusts BLUE SIDEBAR ADJUST LEVEL.
○ Adjusts the clock frequency (PLL frequency).
○ Adjusts color detail BLUE.
○ Adjusts color detail CYAN.
○ Adjusts color detail GREEN.
○ Adjusts color detail MAGENTA.
○ Adjusts color detail RED.
○ Adjusts color detail YELLOW.
Displays the current color system.
Sets the color system to AUTO.
Sets the color system to NTSC.
Sets the color system to PAL.
Sets the color system to SECAM.
Sets the color system to 4.43NTSC.
Sets the color system to PAL M.
Sets the color system to PAL N.
○ Sets the Normal color mode.
○ Sets the ISF color mode (retake).
○ Adjusts contrast.
Displays the current COLOR OFF setting.
Disables COLOR OFF.
Enables COLOR OFF.
○
○ Adjusts the phase (PLL phase).
22
= values not stored in the last memory
Description