B.E.G. LUXOMAT PD4-M-DIM-HVAC Installation And Operating Instruction

LUXOMAT
Installation and Operating Instruction for
1. Mounting preparations
Work on the 230 V mains supply
may only be carried out by quali-
fied professionals or by instructed
persons under the direction and
supervision of qualified skilled
electrical personnel in accordance
with electrical regulations.
Disconnect supply before installing!
The device is not suited for safe
disconnection of the mains supply.
When in Master/Slave mode of op-
eration, the Master-appliance must
always be installed at the location
where there is least daylight.
4. DIP switch functions
DIP- ON OFF
switch
1 Semi automatic mode Fully automatic mode
2 LED OFF LED ON
3 Corridor mode Standard mode
Corridor function: After deactivation by an external push
button, the detector switches off and returns to automatic
mode after 5 sec.
5. Putting into operation / Settings
Self test cycle
120 60 50
After an initial 60-second self-test cycle, the LUXOMAT A
40
for operation.
30
15
5
10
Follow-up time for light control
25 22
30 The time can be set infinitely variably at between 1 and 30 minutes.
18
Symbol TEST: Test mode
R1 16
16 10
10
5
Every movement switches on the light for a period of 1 second, switching
6
TEST
3
1 2
it off for a period of 2 seconds after that regardless of the level of
1
TEST brightness
30
15
Twilight-switch for light control (relay 1)
The switch-on value for the light can be set at between 10 and 2000 Lux.
2000
Using the rotary control, the luminance set points can be set as desired.
1200
600 Symbol : Night-time operation
200
40
Symbol : Daytime/Night-time operation
Orientation lighting
ON
60
This rotary controller serves to determine the working time of the
50
30 orientation lighting (fixed to 20 %).
10
5
"ON" for permanent orientation lighting.
OFF
"OFF" for deactiviation of orientation lighting.
7. Option:
B.E.G. LUXOMAT
®
IR-PD-DIM-HKL
30 60
5 15
min min
min min
1500 1000 750 500
max min
50
250 100
1 5 10 15 30
min min min min min
1 10 30 60
ON
min min min min
20 %
OFF RESET TEST
IR-PD-DIM-HKL
Wall bracket for remote
control IR-PD-DIM-HKL
®
B.E.G.-Occupancy detectors
2. Installation of the LUXOMAT
®
PD4-M-DIM-HVAC-FC
A circular opening of
diameter 68 mm must first
of all be produced in the
ceiling.
Having connected up the
cables in accordance with
regulations, the detector is
inserted into the opening
as shown in the drawing
opposite and fixed into
position with the assis-
tance of the spring clip.
The DIP settings are enabled again by
• Adjusting the DIP switches when closed
• Reset with test sun setting at the potentiometers
• Reset when open
Function LEDs OFF: In the open state and in test mode, the
LEDs are always ON.
PD4-M-DIM-HVAC is ready
®
8. Settings by remote control
Resetting when-
50 to 1500
Lux Lux
open: Deletes all
values set with
or
the remote con-
trol, light OFF.
or
1 30
min min
60
5
min
min
20%
max
max
ON
ON OFF
OFF
1 to 60
min min
50
t < 5 sec. 1500
Lux Lux
max
PD4-M-DIM-HVAC
3. Position DIP-switches
Follow-up time for appliance-control
120 60 50
A
The time can be set infinitely variably at between 5
40
30
minutes and 120 minutes. After 15 minutes the switch-on
15
5
10
delay is activated. This is around 5min. If there are not
detected any further movements within this period, the
switch-on delay starts again.
16 10
5
Symbol : Impulse = 2.5 sec.
2
Symbol A: Alarm impulse = 2 sec.
1
TEST
30
15
Alarm impulse
In order to set off an alarm impulse, at least 3 move-
ments within 9sec. have to be detected.
2000
1200
Pulse spacing PD-Slave
600
2 or 9 seconds can be set for the pause between 2
200
9s 2s
40 pulses sent to the master. The setting can be made with
activated ( ) or deactivated ( ) LED indicator.
LED ON For devices with a separate slave input, 2 sec. can be
LED OFF
set.
Unlocking device – Activation of
the programming mode
Luminance set point for constant
light control
max
Dimming of the lighting on the
desired luminance value
ON
Automatic reading in the current light
value as new luminance set point
OFF
Follow-up time Channel 1
50 1500
1 - 30 min.
Lux Lux
Follow-up time Channel 2 (HVAC)
50 5 - 60 min. or impulse
1500
Lux
Lux
Fully automatic/semi automatic
mode => (see page 2, point10)
Orientation lighting ON/OFF
20 % of the nominal light
Orientation lighting and its
max
follow-up time
Preset/user mode
ON
=> (see page 2, point 11 )
OFF
Locking device – Exit programming
mode
LED flashes
Permanent protection against
sabotage
PD4-M-DIM-HVAC-FC
Flush Ceiling
The DIP switch settings are overriden using
the remote control.
6. Settings carried out using remote
control (optional)
ON
OFF
1
2
DIP
3
1. Check Battery:
Open battery compartment by pressing the plastic
springs together and removing the battery-holder.
TEST
1 2
25 22
30
18
R1 16
10
6
TEST 3
1
2. IMPORTANT
Please pay attention, that the setting is Potentiometer
1 at "TEST" and Potentiometer 2 not at
"SUN". All values which have been programmed
using the remote control will be deleted in the
event of power failure in the position "TEST/
SUN". Please switch Potentiometer 2 over to
"MOON" or any other value.
Caution:
Settings with remote control supersede the settings
by courtesy of potentiometers.
9. Explanation of the remote control button functions
In the initialization period
During initialization phase/self test cycle
Lights can be set to on or off status during initialization(60 Seconds) by
using INI OFF/ON mode.
Light on / off when closed
=> (see page 2, point 12)
Dimming in the closed state
50
1500
Lux => (see page 2, point 11)
Lux
Test operation in the closed condition to enable
Disable the test mode: press reset
Resetting when closed
The lighting relay is switched off, i.e. opened and the follow-up times
reset.
Permanent protection against sabotage
This function blocks the unit permanently (green LED is illuminated). This
operating mode can only be activated during the period of 5 seconds
after pressing the "lock" button. This status will only permit actuating the
t < 5 s
function "Light on/Light off". The procedure for leaving this mode is as
follows:
1. Switch off the current
2. Apply current for 31 - 59 seconds
3. Switch of the current again
4. Apply current
5. Open detector
50
1500
Dim in the open state
Lux
Lux
To set a target value, proceed as follows (example workplace):Place one
lux meter flat on the desk. Set the light. With the help of remote control
IR-PD4-DIM by pressing the buttons „max" or „min" as necessary. Wait
50
1500
until the desired light level is reached.
Lux
Lux
Confirmation by the preset value
50 1500
max
Light during the initialization
Lux Lux
The light is on by default in the initialization time.
On / off with the „Light" button during Initialization. The final condition
max
is then active.
ON
Orientation light ON / OFF when open
Note: Also during the orientation phase of the light constant light control is
ON
OFF
active: With sufficient brightness is <20% dimmed and turned off the lights
if necessary.
OFF
GB
2
1
3
DIP
OFF
ON
Remote control LUXOMAT
®
120 60 50
A
IR-PDim
40
30
15
5 10
16 10
5
2
1
30
15
1
2
25 22 2000
30
2000
18 1200
1200
R1 16
600
600
10
200
6
200
TEST 3
40
1
40