Advertisement
Installing Cisco TelePresence System Profile 55" Dual
4
unpacking the monitor box and lifting out the monitors; fastening the monitors to the bottom module
Unpack the
monitor box.
Lift out to open
the snap lockers.
1.
Carefully lift the right monitor out of
the packaging as illustrated.
2.
See the two triangle holes in the
monitor base. Use these holes to
help guiding the monitor to enter the
poles on the column.
Triangular holes to
guide the monitor
3.
Repeat the above procedure for the
left monitor.
6
mounting the camera cables and the camera
1.
Locate the camera cables in the bottom module (the two long
cables).
2.
Locate the hole in the monitor where the cables can be
pushed through. Push the cables through the hole in the right
monitor.
3.
On the rear side, place the cables in the foam rails that are
going on the rear side of the monitor.
78-20440-01 Profile 55 Dual Installation Sheet | 2011 OCTOBER | © 2011 Cisco Systems, Inc. All rights reserved.
LIFTING HANDLES. Locate the
orange lifting handles in the front
heaVy
and rear side of the monitor.
caution
Left monitor
Right monitor
Allen key
4 * M8×15
4.
Connect the RJ45 and HDMI cables to the camera, see
illustration.
5.
Place the camera and slide it towards the front.
6.
Place the camera cables in the foam rails.
CAMERA CABLE CONFIGURATION
PrecisionHD 1080p
RJ45
HDMI
For countries with 60 Hz current frequency
you must set the PrecisionHD 1080p camera
DIP switch to: 00100.
4.
Align the monitors at the top and fasten the two monitors
together using the upper monitor bracket and the M4×25
screws.
5.
Fasten the two monitors together at the bottom using the
lower monitor bracket and the M4×8 screws.
6.
Fasten the monitor to the column poles using
four M8×15 screws, two screws at each monitor.
7.
Tighten the monitor gently to the bottom module until the
monitor cannot be moved anymore.
Upper monitor
bracket
Lower monitor
bracket*
* The lower monitor bracket is not used on a wall
mounted system. Instead, make sure the monitors
are aligned at the front.
7
mounting the back cover and top lid, and finishing up
Top lid
1.
Hook on the back cover in the
slots at the top and snap it in place
with the lower magnets.
The magnets are strong. Make
sure your fingers are not trapped.
2.
Fasten the back cover with two
M4×15 bolts and nuts (tool: Allen
key).
3.
Slide the top lid into position and
snap it tight with the magnets.
Back cover
4.
Remove the plastic foils
from the screen and the
monitor frame.
5.
Snap on the two speaker
grilles.
6.
Use the supplied cloth to
clean the system.
Page 2
5
connecting the monitor cables to both monitors
Open the front door and locate the monitor connectors and cables. Connect the cables
as illustrated below.
Connect the left monitor:
Connect the right monitor:
1.
HDMI cable
1.
HDMI cable
2.
Speaker in, 15 pin D-SUB cable
2.
Speaker in, 15 pin D-SUB cable
(tighten the screws)
(tighten the screws)
3.
Power cable
3.
Power cable
left monitor connectors
Power
HDMI 1
right monitor connectors
A 级声明 (A Class product declaration)
HDMI 1
Speaker in
本产品为 A 级 ITE，在其使用说明，铭牌等显著位置中已包含如下内容的声明
(We declare here that the subject product is A class ITE product, and the
following statement is clearly marked in the user manual or nameplate):
emc a class declaration
警告
此为 A 级产品。在生活环境中，该产品可能会造成无线电干扰。在这种
情况下，可能需要用户对干扰采取切实可行的措施。
warning:
WARNING:
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate measures.
This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
8
connecting the system
1.
Open the rear door and lead the cables
5.
Connect the power cable (use the
声明所在位置 (Position of the Declaration):
out through the openings at the lower
provided country specific cable).
使用说明 User Manual
part of the door.
铭牌 Nameplate
6.
Open the front door and turn on the
2.
Close the rear door carefully. Take care
monitor.
not to shut the cables in the door.
7.
Follow the instructions in the
申请号 (Application No.)：
accompanying Touch 8" installation
3.
Place the PC cable and the
申请人 (Applicant):
guide to connect and initialize the touch
microphones on the table.
型号
(Model Number)：
interface device.
4.
Connect the Ethernet cable.
8.
The system should be up and running
in a few minutes.
签字/盖章 Signature/Stamp:
日期 Date:
The rear door
Microphone cable
Power cable
Speaker in
Power
Ethernet cable
PC cable
Advertisement
