Advertisement
• Panasonic assumes no responsibility for injuries or property damage resulting
CAUTION
from failures arising out of improper installation or operation inconsistent with this
documentation.
I Be sure to put on a glove to avoid electric shock or injury.
For Your Safety
I Confirm both sides of the screen are hung in the same height
slots.
To prevent severe injury and loss of life, read this section carefully before using the
I Make sure to tighten the height adjustment handles after
unit to ensure proper and safe operation of your unit.
adjusting the screen height.
• This section explains the graphic symbols used in this manual.
I Confirm the bolts of the unit are certainly caught by the wall
mounting plate by pulling the unit after hanging the unit on the
wall mounting plate if the unit is mounted on a wall.
Denotes a potential hazard that could result in
WARNING
serious injury or death.
I After installing or moving the
electronic board, lock the
casters and set the fall-
Denotes hazards that could result in minor
CAUTION
prevention extension legs.
injury or damage to the unit.
Locking the casters
(Push to lock)
These symbols are used to alert operators to a specific
operating procedure that must not be performed.
I Move this unit with two persons. Otherwise, this unit may fall
down and cause injury.
These symbols are used to alert operators to a specific
operating procedure that must be emphasized in order
I When using the stand, be sure to watch your step so that you do
to operate the unit safely.
not bump into or trip over the fall-prevention extension legs.The
label of precautions is attached to the stand UE-608005 (sold
separately).
I For your safety, connect the lead wire
WARNING
securely to the terminal.
(Refer to step 31.)
I Notes in the operating instructions or notes of labels on the
cabinet, chassis or parts should be observed.
I Be sure to use the specified parts for the installation. Otherwise,
it may cause fire, electric shock or injury.
I Plug the power cord firmly into an AC outlet. Otherwise, it can
cause fire or electric shock.
I Safety check must be done by qualified service personnel after
I Do not position the unit in a location where it is unstable.
installing this option.
I Do not attach the electronic board to mortared walls. Accidental
I Have the unit installed, removed and disposed of only by
electric leakage from the wall mounting plate bolts to metal laths
qualified service personnel.
or wire laths can cause heat, smoke or fire.
I If the unit is hung on a wall, confirm the wall must be capable of
supporting at least the following weight.
1,568 N (160 kgf)
I Be sure to disconnect the power cord while installing the unit.
Otherwise, it may cause electric shock or injury.
I To ensure safe operation the power cord supplied must be
inserted into a standard three-prong AC outlet which is
effectively grounded (earthed) through the normal wiring.
I The fact that the equipment operates satisfactorily does not
imply that the power point is grounded (earthed) and that the
installation is completely safe. For your safety, if in any doubt
about the effective grounding (earthing) of the power point,
consult a qualified electrician.
I Do not use damaged plugs or warped outlets. Otherwise, it may
cause fire, electric shock, or short circuit.
I During thunderstorms, do not touch the unit and plug. It may
cause an electric shock.
I Do not alter the unit or modify any parts. Alteration or
modification can cause fire or electric shock.
UB-5365
Center of the electronic board (screen)
H: 900 mm (2 ft. 11 7/16 in.)
H: 812.8 mm (2 ft. 8 in.)
V: 940 mm (3 ft. 1 in.)
Cautions for Wall Mounting
4
Concerning the Screws and Bolts Used
Construction
•
When obtaining anchors and bolts locally, be absolutely sure that they satisfy
the required specifications.
•
Use the values recommended by the manufacturer of the anchors used for
Which method should be used to mount the electronic board depends greatly on
the depth to which the anchors are to be embedded in the wall.
•
the structure of the wall. The system to be mounted on the wall is heavy. Before
Use M6 bolts when the anchors have internal screw threads.
proceeding with installation, therefore, consult with the building manager,
•
Ensure that the M6 bolt has a mated length of 9 mm (
maintenance engineer or designer to verify that the wall has a structure strong
(Below)
enough to support the weight of the system. For safety, install the electronic board
Installation Surface
only after thoroughly understanding the type of walls, the appropriate types of
Anchor (internal thread)
screws and the construction method.
9 mm (
Flat Washer [max. diameter of 16 mm (
I Necessary Tools and Parts
Spring Washer
Tools Required for Assembly
M6 Bolt
Phillips Head Screwdriver . . . . . . 1
•
Ensure that the M6 bolts do not strike the bottoms of the anchors, and check
Tools and Parts Required for Wall-Mounting Work
that they have been tightened up securely.
•
Recommended tightening torque: 5.2 N•m (53 kgf•cm)
Anchor . . . . . . . . . . . . . . . 4
The specified pull-out strength is required
M6 Bolt. . . . . . . . . . . . . . . 4
per anchor.
5
Other Checkpoints
Flat Washer . . . . . . . . . . . 4
M6 anchor bolts are used when installing the
•
Make sure that the location is large enough to accommodate the electronic
Spring Washer . . . . . . . . . 4
electronic board on the wall.
[Specified pull-out strength: 784 N (80 kgf)]
board.
UB-5365
Height: greater than 1,480 mm (4 ft. 10
Drill, measuring tape, level, dust pump, hammer, torque driver (capable to specify
Width: greater than 1,580 mm (5 ft. 2
torque*
1
)
UB-5865
Height: greater than 1,480 mm (4 ft. 10
*1 The range in which the torque can be specified is limited. Use the correct
Width: greater than 1,950 mm (6 ft. 4
torque. [Recommended tightening torque: 5.2 N•m (53 kgf•cm)]
•
Place the AC outlet in the position outlined below.
1
— Within 3 m (9ft. 10
/
8
in.) of the electronic board mounting position
— Not behind the electronic board
I Checkpoints to be Observed While Working
1
Work-Related Safety Precautions
•
Before mounting the electronic board, read through the following points, and
take care to avoid accidents.
— To ensure that the work is accomplished safely and properly, make it a
basic rule to strictly observe all other applicable aspects of safety control.
— If there is a chance that the unit has ended up being deformed or damaged
by unexpected impact while it was being transported and installed, do not
install it without taking appropriate measures. Otherwise, it may fall off the
wall.
2
Concerning Installation
•
The electronic board is for indoor use. It cannot be used outdoors. Neither can
it be installed or used in the following kinds of places.
— Places where it will be directly exposed to rain or water (including under
the eaves of a house)
— Places with a lot of steam or grease such as manufacturing plants or
kitchens, places with special environments such as those with combustible
atmospheres
— Seaborne or coastal places and places where corrosive gases are given off
— Places where the operating temperature range of the electronic board
[temperature: 10 °C to 35 °C (50 °F to 95 °F), humidity: 30 % to 80 %] will
be exceeded
•
To prevent deformation and discoloring, avoid installing the unit in places
exposed to direct sunlight or near heating or cooling appliances, etc.
3
Concerning the Installation Surface
•
Avoid mounting the unit on a wall, which is not a principal structure
component [a concrete wall which is at least 120 mm (4
3
/
in.) thick], with a
4
plasterboard, plywood or other such construction since these walls are weak.
If mounting on such a wall is unavoidable, reinforce the wall adequately (by
ensuring that its ultimate strength will be at least as great as the specified pull-
out strength of the anchors).
UB-5865
Center of the electronic board (screen)
I Wall-mounting and electronic board assembly
1
3
Use the template from the Installation Manual to mark
Hammer in the anchors.
the position on the wall.
11
/
in.) or longer.
32
H: 900 mm (2 ft. 11 7/16 in.)
A
B
C
11
/
32
in.) or longer
H: 812.8 mm
V: 940 mm
(2 ft. 8 in.)
5
/
in.)]
8
(3 ft. 1 in.)
A
B
C
•
Make marks at
A
and
C
or
B
and
C
.
9
/
32
in.)
7
/
in.)
32
9
/
in.)
32
4
Fix electronic board accessories
25
/
in.)
32
attachments) to the wall with M6 screws.
2
Drill 4 holes in the wall.
5
•
Refer to steps 9 and on under "I Assembling the
Optional Stand and Electronic Board".
•
Steps 19 to 23 and 32 are unnecessary.
H: 518 mm (20 3/8 in.)
H: 440 mm (17 11/32 in.)
and
(board
Advertisement
