Radial Engineering ProAV2 User Manual

1
INPUT PANEL
¼" INPUTS - left and right stereo
1
input for instruments.
RCA INPUTS - left and right stereo
2
input for -10dB consumer audio
electronics.
3.5mm TRS - input connection
3
for stereo -10dB consumer audio
electronics.
4 -15dB PAD - reduces the input level
by 15dB to prevent overload from
high output devices.
5 LIFT - interrups the ground path
for the right channel only. Helps to
toubleshoot ground loops when using
the ProAV2 with an AC power device
6
like a keyboard.
OUTPUT PANEL
6 LEFT & RIGHT XLR OUTPUT
- balanced, 600 ohm, mic-level
output is 100% transformer-isolated
and compatiable with mic snakes and
console preamps.
7 GROUND - disconnects pin-1 on
the XLR output connector to reduce
noise caused by ground loops.
CONSTRUCTION
8
8 BOOK-END DESIGN - 14 gauge
s t e e l o u t e r s h e l l p r o v i d e s a
protective zone for the switches and
connectors.
9 FULL BOTTOM FOOT - neoprene
foam foot provides electrical isolation
and plenty of friction to stay put.
10 I-BEAM DESIGN - inner steel 13
enclosure is reinforced with I-beam
profile. Eliminates stress that could
torque the PC board and cause
solder joint failure.
MILITARY-GRADE - double-sided
11
PCB is bolted to steel standoffs for
toughness.
12 RADIAL TRANSFORMER - is
protected from electromagnetic
interfierence by a mu-metal can.
11
13 ISOLATED CONNECTORS - are
made from extremely tough glass-
filled nylon for true electrical isolation
from chassis ground.
Radial Engineering ProAV2 User Guide
2 3 4 5
ProAV2 SPECIFICATIONS
Frequency response
Total harmonic distortion
Input
Outputs
Input pad
Power requirement
7 6
Size
Weight
RADIAL LIMITED THREE YEAR TRANSFERABLE
Radial Engineering - a division of JP Cabletek Electronics Ltd. warrants this product
to be free from defects in material and workmanship and will remedy any such defects
free of charge according to the terms of this warranty. Radial Engineering will repair
or replace at its option any defective component(s) of this product, excluding the
finish, the bottom foam pad and wear and tear from normal use, for a period of three
9
(3) years from the original date of purchase. In the event that a particular product
is no longer available, Radial Engineering reserves the right to replace the product
with a similar product of equal or greater value. To make a request or claim under
this limited warranty, the product must be returned prepaid in the original shipping
container (or equivalent) to Radial Engineering or to an authorized repair centre and
10
you must assume the risk of loss or damage. A copy of the original invoice showing
date of purchase and the dealer name must accompany any request for work to
be performed under this limited warranty. This limited warranty shall not apply if
the product has been damaged due to abuse, misuse, misapplication, accident or
as a result of service or modification by any other than an authorized repair centre.
THERE ARE NO EXPRESSED WARRANTIES OTHER THAN THOSE ON THE FACE
HEREOF AND DESCRIBED ABOVE. NO WARRANTIES, WHETHER EXPRESSED
OR IMPLIED, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL
EXTEND BEYOND THE RESPECTIVE WARRANTY PERIOD DESCRIBED ABOVE
OF THREE YEARS. RADIAL ENGINEERING SHALL NOT BE RESPONSIBLE OR
LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR
LOSS ARISING FROM THE USE OF THIS PRODUCT. THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS,
12
WHICH MAY VARY DEPENDING ON WHERE YOU LIVE.
Radial Engineering
20Hz to 20kHz +/- 2.5dB
0.01% THD 20Hz to 20kHz
Unbal. high-Z
Balanced 600-Ohm, mic-level, pin-2 hot
-15dB
None, completely passive
3.25" x 5" x 1.875"
1.8 lbs.
WARRANTY
ProAV2 User Guide
True to the Music
ProAV2 Stereo Direct Box
Users Guide
Radial Engineering
1638 Kebet Way, Port Coquitlam BC V3C 5W9
Tel: 604-942-1001 Fax: 604-942-1010
email: info@radialeng.com
Radial ProAV2 users guide V1.0 - Part #: R870 1145 00
Subject to change without notice