Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ESI 3V-LX-C4848-30 Series
Summary of Contents for ESI 3V-LX-C4848-30 Series
- Page 1 Model 3V-LX-C4848-24-_ __ VICTORY-LX Model 3V-LX-C4848-30-_ __ Model 3V-LX-C4836-24-_ __ Model 3V-LX-C4836-30-_ __ 3 LEG ELECTRIC TABLE BASE Model 3V-LX-C3636-24-_ __ Model 3V-LX-C3636-30-_ __ 3V-LX Rev A 7/17 _ _ _ = SLV, BLK or WHT ASSEMBLY AND OPERATION...
-
Page 2: Table Of Contents
VICTORY-LX 3 LEG ELECTRIC TABLE BASE PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly procedures. Check that all the parts shown below were provided with your order. Contact your supplier if any materials are missing. Do not discard the your satisfaction. -
Page 3: Motor
ASSEMBLY VICTORY-LX 3 LEG ELECTRIC TABLE BASE STEP 1 Motor Place the table top facing down on a soft clean surface. STEP 2 Attach the center leg brackets to the center leg (the leg with the glide on the end opposite the motor). •... - Page 4 VICTORY-LX 3 LEG ELECTRIC TABLE BASE ASSEMBLY STEP 4 Use the 5mm Allen key to attach the three top M6x18 Round Point supports to the leg columns. • Use two M6x18 socket head screws (with round point tip) per top support. •...
-
Page 5: Cross Channels
ASSEMBLY VICTORY-LX 3 LEG ELECTRIC TABLE BASE STEP 6 Outer Cross Channels Attach the cross outer channels to the outer leg columns with four M6x18 socket head screws per leg. • Use a 5mm Allen key. • Place the guides into the cross channels. •... -
Page 6: Top Supports
VICTORY-LX 3 LEG ELECTRIC TABLE BASE ASSEMBLY STEP 9 Adjust the position of the frame before attaching it to the table. • Check that the top supports on each side are approximately 1" (25mm) from the ends of the table. •... -
Page 7: M3X20
ASSEMBLY VICTORY-LX 3 LEG ELECTRIC TABLE BASE STEP 12 Attach the cross channels to the table. M6x20 • Position one U-bracket over each section of cross channel, between the set screws, as shown (four brackets total). • Use the remaining M6x20 Phillips round head screws (16 total) to fasten the U-brackets to the work surface. -
Page 8: Digital Keypad
• If there are problems with operation, check that all cable and cord connections are secure. If problems continue, call ESI Customer Service. STEP 17 Use the cord clips to secure the cables and cords in position. -
Page 9: Hole Cover
ASSEMBLY VICTORY-LX 3 LEG ELECTRIC TABLE BASE STEP 18 Hole Cover If desired, snap hole covers over all screw holes with guides (26 total). STEP 19 IMPORTANT: There must be 1" (25mm) of clearance on all sides of the work surface (and other moving parts) to ensure free, unobstructed movement. - Page 10 VICTORY-LX 3 LEG ELECTRIC TABLE BASE OPERATION Digital DOWN “SET” Button Display Button Button CAUTION: The initialization procedure must be completed before operating the table. See Step 16 on page 8. Memory Buttons GENERAL OPERATION Table movement stops when you Move the table up or down by pressing UP or DOWN until...
- Page 11 OPERATION VICTORY-LX 3 LEG ELECTRIC TABLE BASE CHANGING THE HEIGHT DISPLAY UNITS This function allows you to change the display units from centimeters to inches or the other way around. • Press and hold S, then press and hold the DOWN button.
- Page 12 800.833.3746 esiergo.com © 2017 ESI Ergonomic Solutions. All rights reserved. 3V-LX Rev A 7/17...