3/23/98 2:32 PM Page 1 MICRO COMPONENT SYSTEM MM-18 SERVICE Manual MICRO COMPONENT SYSTME CONTENTS 1. Precautions 2. Specifications 3. Disassembly and Reassembly 4. Alignment and Adjustments 5. Special Circuit Descriptions 6. Troubleshooting 7. Exploded Views and Parts List 8.
Examples: Handle brackets, Metal Part metal cabinets, screwheads and control shafts. The current measured should not Ohmmeter exceed 0.5 milliamp. Reverse the power- plug prongs in the AC outlet and repeat. Fig. 1-2 Insulation Resistance Test Samsung Electronics...
Page 4
Make sure that the 8. Always connect a test instrument's ground portion around the serviced part has not lead to the instrument chassis ground been damaged. before connecting the positive lead; always remove the instrument's ground lead last. Samsung Electronics...
Page 5
SCAN : Manufactured for Scandinavian KATSO SATEESEEN! Market. VARNING: OSYNLIG LASERSTRÅLNING NAR DENNA DEL AR OPPNAD OCH SPARREN AR URKOPPLAD BETRAKTA EJSTRÅLEN! Fig. 1-4 Warning Labels (Location: Disc Clamper, Inner Side of Unit Door or Nearby Unit Chassis ) Samsung Electronics...
6. After replacing the Pickup, reopen the Short Terminal. See diagrams below: THE UNIT (1) WRIST-STRAP CONDUCTIVE SHEET FOR GROUNDING short short short short terminal terminal terminal terminal SOH-A1 SOH94T4N SOH91CI(CAR,walkman) (CMS-V10,CMS-V30) SOH91VI(LDP) (CMS-V10,CMS-V30) Samsung Electronics...
Page 7
Total harmonic distortion 2.5% Frequency response 20Hz ~ 20KHz(±1dB) Signal to noise ratio 90 dB(1kHz) Compact Disc Channel separation 75 dB(1kHz) Total harmonic distortion 0.1% (1KHz) Audio Output 1V (1kHz 0dB) Specifications are subject to change without notice. Samsung Electronics...
Page 1 3. Disassembly and Reassembly 3-1 Cabinet-Top, Cabinet-Rear 1. Remove 6 screws of ! and 8 screws of @ of its rear part 2. Pull its top part upward vertically as shown in the figure 3-1 Figure 3-1 Samsung Electronics...
3/23/98 2:54 PM Page 2 Disassembly and Reassembly 3-2 Main PCB 1. Pull out the Main-PCB backward horizontally. Figure 3-2 Samsung Electronics...
Page 11
3/23/98 2:54 PM Page 3 Disassembly and Reassembly 3-3 Cabinet-Bottom 1. Pull out the Cabinet-Bottom backward. Figure 3-3 3-4 CD-Pack 1. Undo 4 screws of ! and then remove the CD-Pack downward. Figure 3-4 Samsung Electronics...
Page 12
Remove the Gear (c) ) by pushing the hook. Lift the Gear(b) 1 . 11. Remove the Gear(a) 2 . 11. Remove 2 screws 3 and the then remove the Feed-Motor 4 . 12. Remove the Chassis-Deck (M) 5 . Figure 3-8 Samsung Electronics...
Figure4-2 FM Auto Search Level Adjustment Oscilloscope FM Stereo Adjustment FM antenna SSG FREQ. 98MHz 75Ω Frequency 98MHz Dummy VTVM Speaker Adjustment SEMI-VR(5KΩ) Terminal point (ISVR1) 5KΩ L-CH/R-CH : Maximum(Figure 4-3) Stereo Modulator (Pilot 10%) Figure4-3 FM Stereo Separation Adjustment Samsung Electronics...
Page 14
594 KHz 594 KHz OL 1 Maximum output AM tracking adjustment Non Adjust AM VT(OR1) Input OKV1 GND DC Voltmeter Figure 4-4 VTVM Oscilloscope AM Signal Loop Speaker Generator Test Loop Antenna Jack Terminal Antenna 60 cm Figure 4-5 Samsung Electronics...
Page 15
Set the screw adjustment Press PLAY button after adjustment Speaker Cassette Deck Terminal Frequency Counter LINE OUT output Figure 4-6 Recording /Play head REVERSE PLAY AZIMUTH control knob Figure 4-7 Oscilloscope VTVM Speaker Terminal (GND) In Out Figure 4-8 Samsung Electronics...
Focus error bias can be adjusted from the range of +100mV ~ -100mV by connectiong the resistor with pin 63 (FEBIAS). 164K VB> VA> sev-stopb 160K FEBIAS sev-stop <5 Bit Counter> fcmpo FEBIAS fe-stopb Samsung Electronics...
Page 17
Extracting the DC part of RFI and RFO and comparing with the basic DC level, if RF Level is more than basic level, the FOK is output. The focus OK circuit generates a timing window of focus on to monitor the focus search status of focus serve. VC+0.625V Samsung Electronics...
Page 18
As the asymmertry due to variations in disc manufacturing can not be eilminated by thr AC coupling alone, the reference voltage of EFM comparator is controlled utilizing the fact that the generation probability of 1,0 50% each in the binary EFM signals. 100K 100K Samsung Electronics...
Page 19
Therefore, the output on processing monitor photo diode, must be a controlled current for getting regularly output power, thus the APC (Auto Power Control) circuit is composed. From Micom 150K 0.75K 43.5K 150K 300K 150K 5.15K LDON Samsung Electronics...
Page 20
If the control by MUTE signal from micom exist, and when input signal absent, two channel of right and left is builted in. CH2I CH2O GC2I GC2O GC1I GC1O GC1I CH1O MUTEI (From Micom) 5-1-11 Center Voltage Generation Circuit The Center Voltage is generated by using resistor dividing voltage. Samsung Electronics...
Page 21
After 10-track jumping, servo circuit gets out of the liner range and actuator,s tracking is unstable occasionally. Accordingly, unnecessary jumping with many tracking error should be prevented. 470K 680K 680K TDFCT DFCTI 66PF TRACKING 110K PHASE COMPENSATION 470K FSET Samsung Electronics...
Page 22
The characteristics of high frequency phase compensation in focus tracking servo and the characteristics of cut off frequecny in CLV low pass filter are test by FSET pin. SMON 220K 220K 100K SPDLO SMDP 220K 220K Double speed SPDL- FSET SMEF Samsung Electronics...
LCD lamp is ON (UQ901) & fuse normal Pins73,31 of Connection and soldering of SCON1,2 UIC1(LC72362) is at 5V are normal Voltages at RQ701,RQ702 Replace RQ701,RQ702 are normal Voltages at Replace RQ703 Check Voltage at RIC1 RQ703 is normal Samsung Electronics...
Page 24
(Refer to Schematic Diagram) Voltage between Check pump charge circuitry VT: AM(MW) (OQ5,OQ4) connection of SCON1, Low coverage 0.9V UCON1 soldering of pin77 LW Low coverage 0.7V of LC72362N Check loop antenna soldering and connection of OL1, OL2, OT1,OT2, IT2 Samsung Electronics...
Page 25
Speaker connections are normal Voltages to all pins of AIC601(TA8207) Check power supply section are normal (Refer to Schematic Diagram) Voltage at base of QQ503, Check Muting circuitry QQ553(C945) is less than 0.6V Pattern & Speaker Jack normal Samsung Electronics...
Page 26
Check Roulette Control Sensor Check oscillation of NXF100 Is Focus Search ok ? (16.9344MHZ) Does Laser function during Replace PICK UP Focus Search ? Check NIC9286 pin73 voltage Replace NIC9286 during Focus Search : 5V Replace NIC9223 or NIC9258 Samsung Electronics...
Page 27
Troubleshooting 6-2-2 Audio Output Malfunction Malfunction of Audio Output Check voltage of NIC05 : 5V Replace NIC05 Check waveform of NIC9223 Check NIC9223 soldering pin no. 12,13 Replace NIC9223 Check waveform of NC55R,L Check NIC9223 soldering Check Amp Samsung Electronics...
Page 32
Specification Remarks AH59-90230A SPEAKER-SYSTEM PS17E,MM17,-,- AH81-11047A NET L 157 X 247.2 X 38.4t AH81-11047B NET R 157 X 247.2 X 38.4t AH81-11047C CABINET W138.5 X H233.5 X D180 AH81-11047D WOOFER 5`` SG12G33AFA AH81-11047Z SCREW M4 X 10 BLACK Samsung Electronics...
Page 44
L OUT LEFT L-N3 100K L-N4 100K 0/30dB I CBUS DECDER + LATCHES 2dB STEP R-N1 DIGGND 100K R-N2 100K SPKR ATT VOLUME TREBLE MIDDLE BASS R OUT RIGHT R-N3 Verf 100K R-N4 INPUT MULTIPLEXER AGND 100K GAIN Samsung Electronics...
Page 45
Page 9-6 Block Diagrams LE0731A : ULCD1 SLEEP REP.1 TUNED MONO STEREO TRACK AUTO CLASSIC POPS ROCK PROGRAM INTRO CD -SYNC COM1 COM1 SLEEP COM2 COM2 COM3 COM3 COM1 MONO INTRO AUTO COM2 STEREO PROGRAM COM3 MHz CD-SYNC Samsung Electronics...
Page 48
FS1 to TM to BAL1 to PS1 to GA1 to Equalizer SPDL- BAL5 Spindle Servo LPF (Double Speed) SMDP SMON SMEF Comparator FSET MIRROR MIRROR DETECTION CIRCUIT Defect Dectection Built-in Post Filter Amp (L&R) Circuit FOK DETECTION CIRCUIT Samsung Electronics...
Page 49
When SD SIGNAL is L MODE : ACTION HIGH SPEED MOTOR CTL HIGH SPEED TAPE PLAY TAPE REC CD SYNCHRO RECORDING CONTROL TAPE REC INDICATE FRAME SYNCHRONIZATION STATUS LKFS SOSI SUBCODE SYNCHRONIZATION SIGNAL CD TEST CD PROGRAM CHECK 9-10 Samsung Electronics...
Page 50
FM & AM IF FREQUENCY INPUT PORT SUBPD AMIN AM INPUT AM OSC INPUT FMIN FM INPUT FM OSC INPUT FM TUNING VOLTAGE FM TUNING VOLTAGE FM TUNING VOLTAGE AM TUNING VOLTAGE TEST1 Xout OSC for SYSTEM CLOCK OSC for SYSTEM CLOCK Samsung Electronics 9-11...
Page 51
VSSA Analog VSS for servo part Micom clock input pin MDATA Micom data input pin Micom data latch input pin RESET Reset input pin MIRROR The mirror output for test The output pin of focus OK comparator 9-12 Samsung Electronics...
Page 52
The input pin for AGC The output pin for AGC The input pin for EFM comparating CAGC The capacitor connection pin for AGC Feedback input pin of E I/V amplifier for EF Balance control GND for RF part Samsung Electronics 9-13...
Page 53
Mute control input (“H”: Mute ON) Latch Signal input from Micom (Schmit Trigger) MDAT Latch Signal input from Micom (Schmit Trigger) Latch Signal input from Micom (Schmit Trigger) SRAM data I/O port8 (MSB) SRAM data I/O port7 9-14 Samsung Electronics...
Page 54
Spindle Motor drive (Velocity control in the PHASE mode) BCKI Audio data bit clock input of 48 bit/Slot (2.1168MHz) TESTV TEST input terminal (GND connection) DSPEED TEST input terminal (VDD connection) LRCHI Channel clock input of 48 bit/Slot (44.1KHz) Samsung Electronics 9-15...
FUNCTION & VR CONT QIC501 ASP601 TDA7439 WOOFER TERMINAL SPK(1/2) PRE/REC AMP JIC301 KA22291 AIC601 R/P HEAD TA8207K POWER AMP E-HEAD ASP651 WOOFER TERMINAL SPK(1/2) PT701 TRANS POWER VDE/B.S(230V/240V 50Hz) AC CORD MIC MIXING(OPTION) AUX JACK UCN901 TO CDP PCB 12-1 Samsung Electronics...
Page 61
mm18(5) 3/23/98 4:41 PM Page 3 Voltage Table KB9223 KB9223 KA9258 KB9223 KB9223 IC Name IC Name STOP MODE PLAY MODE STOP MODE PLAY MODE STOP MODE PLAY MODE STOP MODE PLAY MODE STOP MODE PLAY MODE 2.5V 4.5V 2.5V 4.5V 2.5V 2.5V...