Sign in today to find solutions:

Don't have an account? Sign up

RIDGID R840011 Operator's Manual

Ridgid 18 volt drill operator's manual r840011.

 
Your drill has been engineered and manufactured to our high standards for dependability, ease of operation, and operator
safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator's manual before using this product.
Thank you for buying a RIDGID product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
OPERATOR'S MANUAL
1/2 in. 18 VOLT DRILL
2-SPEED
R840011
1

Summary of Contents

  • Page 1

    Your drill has been engineered and manufactured to our high standards for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.

  • Page 2: Table Of Contents

    TABLE OF CONTENTS  Introduction ...2  General Safety Rules ... 3-4  Specific Safety Rules ...4  Safety Rules for Charger ...5  Symbols ... 6-7  Features ... 8-9  Assembly ...0  Operation ... 10-16  Maintenance ... 17-18 ...

  • Page 3: General Safety Rules

    Use of any other batteries may create a risk of fire.  Use battery only with charger listed. MODEL BATTERY PACK R840011 130252004 130252004  Do not abuse the cord. Never use the cord to carry the charger. Keep cord away from heat, oil, sharp edges, or moving parts.

  • Page 4: Specific Safety Rules, General Safety Rules

    GENERAL SAFETY RULES SERVICE  Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury. SPECIFIC SAFETY RULES  Use auxiliary handles supplied with the tool. Loss of control can cause personal injury.

  • Page 5: Safety Rules For Charger

    SAFETY RULES FOR CHARGER WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.  Before using battery charger, read all instructions and cautionary markings in this manual, on battery charger, battery, and product using battery to prevent misuse of the products and possible injury or damage.

  • Page 6: Symbols

    SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta- tion of these symbols will allow you to operate the tool better and safer. SYMBOL NAME Volts Amperes Hertz Watt Minutes Alternating Current...

  • Page 7

    SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL DANGER: WARNING: CAUTION: CAUTION: SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to the nearest AUTHORIZED SERVICE CENTER for repair.

  • Page 8: Features

    FEATURES PRODUCT SPECIFICATIONS Keyless Chuck ... 1/2 in. Keyless Motor ...18 Volt DC Switch ...Variable Speed Gear Train ... 2 Speed No Load Speed ...0-450/0-1,500/min. TORQUE ADJUSTMENT RING KEYLESS CHUCK BATTERY PACK CHARGER Clutch ... 24 Positions Charger Input ... 120 V, 60 Hz, AC only Charge Rate ...

  • Page 9: Assembly, Features

    The two-speed gear train is designed for drilling or driving at LO (1) or HI (2) speeds. A slide switch is located on top of the drill for selecting either LO (1) or HI (2) speed. VARIABLE SPEED The variable speed switch trigger delivers higher speed with increased trigger pressure and lower speed with decreased trigger pressure.

  • Page 10

    OPERATION WARNING: Do not allow familiarity with your tool to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury.

  • Page 11

    OPERATION LED FUNCTION OF CHARGER See Figure 3. INDICATOR Power Evaluate Evaluate Evaluate Charging Full GREEN LED RED LED BATTERY PACK Without battery pack ON Hot battery pack Flashing Cold battery pack Flashing Deeply discharged Flashing Fast charging Slow charging POWER INDICATOR EVALUATE...

  • Page 12

    SWITCH TRIGGER See Figure 5. To turn the drill ON, depress the switch trigger. To turn it OFF, release the switch trigger. VARIABLE SPEED The variable speed switch trigger delivers higher speed and torque with increased trigger pressure and lower speed with decreased trigger pressure.

  • Page 13

    The drill has a two-speed gear train designed for drilling or driving at LO (1) or HI (2) speeds. A slide switch is located on top of the drill to select either LO (1) or HI (2) speed. When using drill in the LO (1) speed range, speed will decrease and unit will have more power and torque.

  • Page 14

    • For heavy drilling BIT STORAGE See Figure 9. When not in use, the bit provided with this drill can be placed in the storage area located on the rear of the drill.\ INSTALLING BITS See Figure 10 - 11.

  • Page 15

    USING THE AUXILIARY HANDLE ASSEMBLY See Figure 12. An auxiliary handle assembly is packed with the drill for ease of operation and to help prevent loss of control. The handle can be rotated 360°, and it can also be mounted on the opposite side for left hand use.

  • Page 16

     Secure the material to be drilled in a vise or with clamps to keep it from turning as the drill bit rotates.  Hold the drill firmly and place the bit at the point to be drilled.  Depress the switch trigger to start the drill.

  • Page 17

    Only the parts shown on the parts list are intended to be repaired or replaced by the customer. All other parts should be replaced at a RIDGID authorized service center. BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING...

  • Page 18

     Insert a 5/16 in. or larger hex key into the chuck of the drill and tighten the chuck jaws securely.  Tap the hex key sharply with a mallet in a clockwise di- rection. This will loosen the screw in the chuck for easy removal.

  • Page 19: Warranty

    2/1/04 and after. This product is manufactured by One World Technologies, Inc. The trademark is licensed from RIDGID, Inc. All warranty communications should be directed to One World Technologies, Inc., attn: RIDGID Hand Held and Stationary Power Tool Technical Service at (toll free) 1-866-539-1710.

  • Page 20

    R840011 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgid.com.

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: