Hawking HOW2R1 Quick Installation Manual

Part No. HOW2R1
Start Here


System Requirements

• Web UI configuration requires Internet Explorer, Mozilla
Firefox or Safari Web Browsers
• Software configuration requires computer w/ CD-ROM drive
• 802.11b, 802.11g or 802.11n Wireless Network
1
Hardware Setup for Initial Configuration
First you must set up the hardware according to the diagram on the
right for the initial setup of the Outdoor Smart Repeater. After the
initial setup is complete, you may relocate the repeater and mount it
in your desired location.
A. Attach the antennas to the antenna connectors
(The L-Shape connector establishes signal diversity. It is highly
recommended to use the L-shape connector for optimal wireless
performance)
B. Attach an Ethernet cable from the PoE Injector port labeled
"Power" to the Ethernet Port on the Outdoor Smart Repeater.
C. Attach the power adapter and power cable to the PoE Injector
2
Accessing the Smart Repeater for Initial Configuration
There are two ways to access the smart repeater: (1) Wire-
less Connection, or (2) Wired connection.
(1) To access the repeater using a wireless connection: Use
a computer with wireless network, connect to the Repeater
by searching for the wireless network named:
Outdoor_Repeater.
(2) To access your repeater using a wired connection, you
must connect your computer to the port labeled "LAN" on the
PoE Injector using an ethernet cable. Note: LAN port is
located next to the power plug. Also, be sure that you have
the hardware setup as instructed in Step 1.
Using the same computer, open a web browser and type in the following web
address in the web address bar:
3

Configuration Settings

The Setup Wizard will now prompt you to auto-
matically configure your IP settings
(recommended) and enter a security key* if the
network you are connecting to is an encrypted
network. Enter the key and click Continue.
*If you do not know the security key of the network you are
connecting to, consult the network administrator.
Technical Support: 1.888.202.3344 or techsupport@hawkingtech.com
A
Accessing with your Windows PC (Wireless)
When the "Network Availability"
window pops up on the "Start"
toolbar, Click on the "Connect to a
network" link. Once the "Connect
to a network" window opens,
Select on the "Outdoor_Repeater"
Network.
http://192.168.5.220
Once the page loads, enter the
following login information:
Login: admin
Password: 1234
Click Login to
continue.
Q UI CK I N S T AL L AT I O N GU I D E
Hi-Gain Outdoor Wireless-N Dual Radio Smart Repeater
™
Check Package Contents
• 1 x Hi-Gain Outdoor Wireless-N
™
Dual Radio Smart Repeater
• 2 x Hi-Gain Outdoor Antennas
• 1 x PoE Injector
• 1 x L-shape antenna connector
• 1 x Waterproof Gasket Kit for RJ-45
Hi-Gain Outdoor Dual Radio Smart Repeater
™
A
B
Power over Ethernet (PoE) Injector
Click Scan to find your wireless Internet connection. After the list appears,
select the connection and click Connect.
IP Settings
• 1 x Power Cable and
Power Transformer
• 1 x Ethernet Cable
• 1 x Mounting Kit
• 1 x Setup CD-Rom
C
Accessing with your Mac (Wireless)
Click on the
"Airport" icon in the
"apple" toolbar.
Click on the
"Outdoor_Repeater
Outdoor_Repeater
" network from the
drop-down menu.
If the signal strength is low or your
network does not appear, you may need
to readjust your location of your Repeater
or the position of its antennas. The
"Hawking" Logo should face towards the
wireless source.
Click Scan to try again.
Click Connect to continue.
Wireless Security
www.hawkingtech.com