1. Manuals
  2. Brands
  3. Hilti Manuals
  4. Robotics
  5. pos 150
  6. Manual

Hilti POS 150 Manual

Total station
Hide thumbs Also See for POS 150:

Advertisement

Table of Contents

POS 150/180
English
Printed: 24.04.2018 | Doc-Nr: PUB / 5153820 / 000 / 05

Advertisement

Table of Contents
loading

Related Manuals for Hilti POS 150

Summary of Contents for Hilti POS 150

  • Page 1 POS 150/180 English Printed: 24.04.2018 | Doc-Nr: PUB / 5153820 / 000 / 05...
  • Page 2 Printed: 24.04.2018 | Doc-Nr: PUB / 5153820 / 000 / 05...

  • Page 3: Information About The Documentation

    Information about the documentation About this documentation • Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product. • Observe the safety instructions and warnings in this documentation and on the product. •...
  • Page 4 The type designation and serial number are printed on the rating plate. ▶ Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product. Product information...
  • Page 5 ▶ Do not use or charge batteries that have suffered mechanical impact, have been dropped from a height or show signs of damage. In this case, always contact your Hilti Service. ▶ If the battery is too hot to touch it may be defective. In this case, place the product in a non-flammable location, well away from flammable materials, where it can be kept under observation and allowed to cool down.
  • Page 6 Check the accuracy of the tool by taking measurements by other means when working under such conditions or if you are unsure. Likewise, Hilti cannot rule out the possibility of interference with other devices (e.g. aircraft navigation equipment). The tool complies with the requirements of Class A; the possibility of interference occurring in a domestic environment cannot be excluded.
  • Page 7 Description Total station front Grip Telescope with laser distancer Focusing knob Lens Vertical drive Guide light § Horizontal drive Operator keyboard Tripod lock Display & Sight English Printed: 24.04.2018 | Doc-Nr: PUB / 5153820 / 000 / 05...
  • Page 8 Total station rear side Radio antenna Eyepiece ∙ ¡ Battery compartment lock Tripod screw Battery compartment Laser plummet £ Circular bubble level POC 100 Display USB socket (master) Control panel USB socket (slave) & Charging socket English Printed: 24.04.2018 | Doc-Nr: PUB / 5153820 / 000 / 05...
  • Page 9 POC 200 Touchscreen 4-way controller and OK button LED display 4 function buttons Microphone Loudspeaker Eye for theft protection Display lock § Brightness sensor On/off switch & Connector side of the POC 200 HDMI socket Socket for the docking station £...

  • Page 10: Technical Data

    Description of the tool The Hilti POS 150/180 total station can be used to define objects as dynamic positions within a given space or area. The tool is equipped with horizontal and vertical circles with digital graduation, two electronic levels (compensators), a coaxial electronic distance meter (EDM) incorporated in the telescope and an electronic processor system for calculating and saving data.
  • Page 11 Sensitivity to tribrach circular bubble level ± 8' / 2 mm Angle measurement POS 150 accuracy (DIN 18723) 5" POS 180 accuracy (DIN 18723) 3" Laser distance measurement / laser pointer (POS 150/180) Wavelength 660 nm (0.0000260 in) Laser class Beam divergence 0.27 mrad Maximum output power <...
  • Page 12 Motorization (POS 150/180) Rotation speed max. 90°/s Telescope repositioning Rotation 180° (typical) 3.5 s Wireless communication (between the POS 150/180 and POC 100/POC 200) Frequency range 2,400 MHz …2,483.5 MHz Maximum emitted transmission power 19.3 dBm Range 300 m …800 m (984 ft …2,624 ft - 10 in)
  • Page 13 IP 67 Controller (POC 200) IP 65 4.15 Tripod thread Tribrach thread 5/8" 4.16 Temperature (POS 150/180, POC 100) Operating temperature −20 ℃ …50 ℃ (−4 ℉ …122 ℉) Storage temperature −30 ℃ …70 ℃ (−22 ℉ …158 ℉) 4.17...
  • Page 14 POS 150/180 POC 100 POC 200 Weight 0.32 kg 0.25 kg 0.33 kg (0.71 lb) (0.55 lb) (0.73 lb) Operating temperature −20 ℃ …40 ℃ −20 ℃ …40 ℃ −20 ℃ …40 ℃ (−4 ℉ …104 ℉) (−4 ℉ …104 ℉) (−4 ℉...

  • Page 15: First Steps

    First steps Controls and display screens 5.1.1 Control panel on the total station The control panel comprises a 5-line display and four buttons. This control unit is used to make basic settings on the total station. Function buttons on the total station → page 13 Function buttons on the total station Switches the tool on or off Laser plummet on / off...
  • Page 16 The control panel on the controller consists of a total of 7 buttons with symbols plus a touch screen for interactive operation. Function buttons on the controller → page 14 Function buttons on the controller Switches the tool on or off Switches the display backlight on or off Calls up the FNC menu for additional settings Cancels or ends all active functions and returns to the start menu...
  • Page 17 Compensator on / off Active target Type Setting including status laser pointer and the laser plummet Battery state of charge: 0 - 100% 5.1.9 Further information POS 150 (http://qr.hilti.com/r51292) English Printed: 24.04.2018 | Doc-Nr: PUB / 5153820 / 000 / 05...

  • Page 18: Calibration And Adjustment

    Hilti Tool Service or the Hilti Repair Service, as this error requires mechanical correction. As the Hilti total station system is primarily used for measuring applications in one position, it is advisable to calibrate the tool in the field or on the construction site at regular intervals. This is especially the case when steeper sightings are used frequently.

  • Page 19: Troubleshooting

    • to unusual conditions or stress, before important work or at least once a year. Testing and inspection by Hilti Measuring Systems Service does not relieve the user of the obligation to check the scanning tool before and during use.

  • Page 20: Manufacturer's Warranty

    In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti sales representative for further information. In accordance with the European Directive on waste electrical and electronic equipment and its implemen- tation in conformance with national law, electric tools or appliances that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
  • Page 21 Printed: 24.04.2018 | Doc-Nr: PUB / 5153820 / 000 / 05...
  • Page 22 Printed: 24.04.2018 | Doc-Nr: PUB / 5153820 / 000 / 05...
  • Page 23 Printed: 24.04.2018 | Doc-Nr: PUB / 5153820 / 000 / 05...
  • Page 24 Hilti = registered trademark of Hilti Corp., Schaan 20180411 Printed: 24.04.2018 | Doc-Nr: PUB / 5153820 / 000 / 05...

This manual is also suitable for:

Pos 180

Table of Contents