Honeywell EQUIP Series Quick Install Manual

EQUIP Series
TM
High Definition (720p) True Day/Night IP Dome Camera
Quick Install Guide
Document 800-05621 – Rev A – 02/10
Introduction
Thank you for purchasing a Honeywell HD4 EQUIP Series IP Dome Camera. Before installing
your camera, please verify your model and read this guide carefully.
For detailed information for your specific camera, please refer to the appropriate user guide
located on the IP Utility CD. When you install the Honeywell IP Utility software, the User Guide
will automatically be downloaded to your computer.
Before installing the camera, Honeywell recommends that you go to
products/cameras/index.html and look under Indoor/Outdoor Mini-domes to find your camera,
then download the latest manuals and software updates.
1
Preparation
Removing the Dome Bubble
and Turret
Dome bubble
1. Using the supplied Allen key, loosen the
captive screws on the dome bubble.
Remove the dome bubble and set it aside.
2. Gently pull the turret off the gimbal, then set
Gimbal
it aside.
Removing the Gimbal
Remove the gimbal from the enclosure base so
you can easily access the mounting holes (see
illustration).
Metal
1. Squeeze the 4 black tabs until they are free
hinge
of the black clips.
2. Elevate the hinge until the gimbal is above
the housing and you have access to the
enclosure base mounting holes.
Caution When elevating the hinge, do not
overstress the two ribbon cables.
If necessary, rotate the gimbal to
provide additional slack.
Document 800-05621 – Rev A – 02/10
Preparing the Mounting Surface
1. Use the mounting template to mark the mounting
surface for the screw holes and the cable access hole.
Note To prevent moisture from entering the housing,
position the enclosure with the side conduit entry
pointing down.
2. Pre-drill holes in the mounting surface as required.
Installing the Conduit Plug
The HD4MDIP/X ships with the conduit plug pre-installed in
the enclosure base back conduit entry. To use the back
conduit entry, remove the conduit plug and install it in the
side conduit entry after loosening the locking screw. (See
Top View in Adjusting the Camera
Retighten the locking screw to secure the conduit plug in
place.
Note For secure installations, protect surface-mounted
cables with plastic or metal cable covers.
Installing the Grommet (optional)
If a conduit is not used for cable routing, install the rubber grommet in the conduit hole (onto the camera base),
then slit the grommet and feed the cables through. Use the appropriate sealant to seal the grommet to prevent
moisture from entering the housing.
www.honeywellvideo.com/
2

Camera Installation

Mounting the Camera
1. Route the cables through your chosen conduit entry.
Turret
2. Mount the camera to a wall or ceiling using the supplied screws.
Note To prevent moisture from entering the housing, ensure that the gasket is flush against the
Black tabs (x4) back of the camera enclosure and is not pinched.
Connecting the Wiring
1. Connect the power input:
• For 24 VAC connection, locate the two-pin green connector that was shipped with your
camera and make the necessary connections.
• For PoE connection, connect a CAT5 cable to the RJ45 network connector.
Mounting
holes
Black clips (x4)
Enclosure base
Conduit
plug locking
screw
Back conduit
entry
in Camera Installation.)
Conduit plug
RJ45 Ethernet network connection
Local video out (adjusting and focusing)
Audio/Alarms
Power: 24 VAC
2. Connect the alarms and audio:
Locate the eight-pin green connector that was shipped with your camera and make all the
necessary connections as shown in the table below.
Side
conduit
entry 24 VAC Audio Alarm
In Out In
2 3 4 5 6 7
1
3. Connect to the network:
If you haven't already connected a CAT5 cable to the RJ45 network connector for PoE, then connect a
CAT5 cable to the RJ45 network connector.
Note For detailed audio and alarm configuration information, refer to the Refence Guide for your
camera located on the IP Utility CD.
Sealing the Wiring
To prevent moisture from entering the housing, if you are using the back conduit entry, apply sealant
around the conduit connection and the mounting screws.
Adjusting the Camera
1. Verify that power is applied to the camera.
Note Please allow the camera to initialize before proceeding. Video output is not instantaneous with
the application of power.
2. Reinstall the gimbal by inserting the black tabs into the black clips on the enclosure base.
3. Connect the supplied video cable to the local video out connector to view the video signal on a
standard monitor (see illustration below for local video out connector location).
4. Loosen the setscrew that locks the gimbal assembly in place to adjust the horizontal rotation.
5. Follow the legend below to adjust the camera (pan, tilt, and focus) to the desired view.
Top View
Setscrew (loosen to
adjust horizontal
rotation)
Set focus
(top)
6. Retighten the setscrew to lock the gimbal assembly in place.
7. Disconnect the supplied video cable.
Reinstalling the Turret and the Dome Bubble
1. Align the turret on the gimbal, then gently press until the turret clicks securely into place.
2. Align the dome bubble captive screws with the mounting holes in the enclosure base, then
securely screw them into place.
PIN Definition
1 Audio In +
2 Audio In –
3 Audio Out +
4 Audio Out –
5 Alarm In +
6 Alarm In –
Out
7 Alarm Out +
8 Alarm Out –
8
Legend
A = Tilt rotation
Set focal length
B = Horizontal rotation
(bottom)
C = Pan rotation
Local video
out
Reset
button
B
C
Loosen locking
screw (inside
A
conduit entry) to
remove the side
conduit plug
Please turn over