Display Settings - RCA RS2653 User Manual

RS2653_55_EN(TCEC) 1/13/06 1:27 PM
General Controls
EN Remote Control
— Turns power on or off from STANDBY mode.
CD — Selects CD player.
TUNER — Selects radio tuner and changes radio band in Tuner mode.
TAPE — Selects tape player.
AUX — Selects Aux mode; turns the system on.
CD INFO — Selects among disc display information.
B. BOOST—Turns Bass Boost on or off.
DEMO/DIMMER —Turns the feature demonstration on or off; adjusts dis-
play brightness;
VOL+ / VOL- — Increases/ decreases volume.
PLAY/PAUSE
NEXT
In Tuner mode - Tunes up radio frequency.
PREV
track; In Tuner mode - Tunes down radio frequency.
OPEN/CLOSE — Opens and closes CD disc tray.
STOP — Stops playing CD.
REPEAT — Repeats a track, CD, or all CDs.
— mutes and restores audio output.
— Turns on/off random playback.
FM ST. — Switches between FM stereo and mono modes.
DISC SKIP — Skips to next CD.
INTRO — Turns INTRO mode on or off to play the first 10 seconds of each
track.
DN•FOLDER/PRESET•UP
station and previous / next folder during mp3/WMA CD playback.
SLEEP — Selects the time interval in minutes before the unit turns off.
Installing Batteries
The remote control must be inserted with 2 "AAA" or "R3" or "UM 4"
batteries prior to use. Follow the steps below to ensure correct installation.
1. Open the battery compartment door (located at the back of the remote
control) by sliding the cover out.
2. Before inserting the batteries, observe the polarities (that is, + and -) of
the battery then relate the polarities to the engraved diagram inside the
battery compartment. Now insert the batteries.
3. After installation of the batteries, place the lit to cover the batteries.
Lightly push it closed with a snap.
4
Page 8
— Plays and pauses current CD.
/FWD — In CD mode - Skips forward to the next CD track;
/REV — In CD mode - Skips backwards to the previous CD
— Selects previous / next tuner preset
Note:
Cassette functions can not be operat-
ed from the remote control.

Display Settings

Display
Showing Demonstration
Press DIMMER•DEMO to turn on/off demonstration
mode. The demonstration scrolls through all display
operations.
Display Clock / Timer
Setting the Clock
1. Press and hold CLOCK until the hour flashes on
the display.
2. Press DIGITAL TUNING or to set the
hour and then press CLOCK to shift to minute
digits.
3. Press DIGITAL TUNING or to set the
minute.
4. Press PROG•SET to save settings or STOP to
quit setting.
Note:
When system is ON, you can press
CLOCK to display the current time
for about 2 seconds.
Setting the Timer
1. Press and hold TIMER until ON (timer on time)
appears with the hour flashing.
2. For setting time, press DIGITAL TUNING or
to set the hour and then press TIMER to shift
to the minute digits.
3. Press DIGITAL TUNING or to set the
minute.
4. Press TIMER to change to OF (timer off time)
with hour flashing. Repeat steps 2 & 3 for timer
off time setting.
5. Press PROG•SET to save settings or STOP to
quit setting.
Note:
The wake up timer source will be
the source you are in when set-
ting the timer.
Activating the Timer
Press and release TIMER to turn on/off the timer. The
timer is active when the clock icon is lit.
Adjusting the Display Brightness
1. Press and hold DIM-
MER•DEMO for more
DIMM 2
than 2 seconds.
2. While the dimmer is
displayed, press and
release DIMMER•DEMO repeatedly to select the
desired level (DIMM 1 - 3).
Sleep Mode
You can select the time interval in minutes before
the unit turns off automatically. Press SLEEP on the
remote to select among OFF, 120, 90, 60, 45, 30, 15
and 5 minutes. (Remote Only)
The sleep icon flashes on the display when sleep
mode is activated.
When sleep is activated, press SLEEP once to view
remaining sleep time.
Press SLEEP again when the remaining sleep time is
displayed to change sleep time.
Note:
Sleep is automatically de-activated
when the unit is turned off.
5
EN