Universal Remote Control CLIKR-5 Operating Instructions

Operating Instructions For 1 1 Introduction 4 4 Button Functions
The CLIKR TM -5 UR5U-8780L & UR5U-8790L is
CLIKR -5
TM
designed to operate the CISCO / SA, Pioneer,
Pace Micro, Samsung and Motorola digital
set tops, Plus the majority of TV, VCR, DVD
Cable Remote Control and AUX equipment on the market as
shown below.
CBL : Cable Set-top Box TV : Televisions
UR5U-8780L & UR5U-8790L VCR : VCRs and TV/VCRs DVD: DVD Players
AUX : Audio Equipment, Media PC, etc.
2 2
Replacing Batteries
Before you program or operate the remote control,
you must install two new AA alkaline batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
5 5 Programming the Remote Control
3 3 Operations
IMPORTANT SETUP NOTE!
In this section when you are instructed to press a [DEVICE] button, that means to press either the CBL, TV, VCR,
DEFAULT STATE:
DVD or AUX button, depending on what device you are programming the remote to operate.
Device Default: Cable Set-Top Box (STB) There are three ways you can program your remote:
* Quick Set-Up Method
Channel Default: CABLE channel and numbers
* The Pre-Programmed 3-Digit Code Method
through the CABLE STB. You have the option of
* The Auto-Search Method
controlling your CABLE channel and numbers
The Quick Set-Up Method is a unique feature that enables the fastest and easiest setup by using a 1 digit code.
through the TV or VCR. Refer to section H for
This is the quickest way to set up devices made by popular manufacturers.
programming steps.
The Pre-Programmed Code Method allows you to setup all of the buttons at once by entering 3-digit code
Volume Default: Volume and Mute control are
numbers that correspond with the components manufacturer/brand. Code tables for this method are on the
automatically transferred to the respective
backside of the operating instructions.
Component based on the Device selected:
The Auto-Search Method scans through all of the codes in the remote control, one at a time allowing you to
CBL:Cable Set-Top Box ; TV:TV ; VCR:TV.
identify the correct code.
DVD:TV ; AUX:AUX. You have the option of
Universal Remote Control, Inc.
IMPORTANT SETUP NOTE!
controlling CABLE Volume and Mute through
www.universalremote.com This pertains to all programming steps. When you are in setup mode the device LED will light for 30 seconds. If you do
the TV, VCR or AUX. Refer to section G for
OCE-0060K Rev 01 (07/13/10) not press a button within 30 seconds, the LED light will turn off and exit setup mode, and you will need to start over.
programming steps.
A. Quick Set-Up Method C. Auto-Search Method E. Programming the AUX Device
STEP1 Turn on the equipment you want to If none of the three digit code numbers You can take advantage of the AUX function to
program. To program your TV, turn on assigned to your brand of equipment works, or
program a devices such as a media PC, gam-
the code table does not list your brand, you can
the TV.
ing console or satellite radio receiver. Follow
use the Auto Search Method to find the correct
the instruction in section B to program an AUX
STEP2 Point the remote at the component and
three-digit code number for your equipment by
device. You can also program the AUX button
press and hold the [DEVICE] key for 3
following steps:
seconds until the Device LED blinks off for a second TV, VCR or DVD player. To do this
STEP1 Turn on the equipment that you want
follow the instructions below.
and turns back on. Continue holding
the remote control to operate (Cable
the [DEVICE] key and press the number
STEP1
Turn on the 5th device you want to
Box, TV, VCR, DVD, etc.).
keys, one at a time, starting with 1, then
program (TV, VCR, DVD, etc.).
STEP2
Press the [DEVICE] button and the
2, 3...0. Stop pressing the number keys
STEP2
Press the [AUX] button and the
[OK/SEL] button simultaneously for
when the device turns off.
[OK/SEL] button simultaneously for 3
three seconds. The device LED will
STEP3 Release the [DEVICE] key to save the
seconds. The [AUX] device LED will
turn on indicating that it is ready to be
code. The Device LED will blink twice
programmed. The LED will remain on turn on for 30 seconds.
to confirm the code is stored.
for 30 seconds. The next step must be
STEP3 Press the [Device] button For the type of
Repeat the steps above for all components
entered while the LED is on.
device you want to setup. Point the
(TV, VCR, DVD, AUX).
STEP3 Press the [CH ] or [CH ] button one
remote control toward the device and
at a time or keep it pressed. The
enter the 3-digit code number assigned
B. Pre-Programmed 3-Dight Code Method
remote will emit a series of Power
to your brand.
ON/OFF code signals. Release the
STEP1 Turn on the equipment that you want
*Note : To program a second TV press TV, etc.
[CH ] or [CH ] button as soon as the
the remote control to operate (Cable
equipment turns off. STEP4 When the equipment turns off verify
Box, TV, VCR, DVD, etc.).
that you have selected the correct
*Note : You can verify that you have selected the
STEP2
Press the [DEVICE] button and the
correct code by pressing the [POWER] code by pressing the [POWER] button.
[OK/SEL] button simultaneously for
button. The equipment should turn back The equipment should turn back on.
three seconds. The corresponding
on. Then try all of the functions on the Then try all of the functions on the
device LED will turn on indicating that
remote control (i.e. volume, mute, etc.) to
remote control (i.e. volume, mute, etc.)
it is ready to be programmed. The LED
ensure you have the correct code. If any of
to ensure you have the correct code.
will remain on for 30 seconds. The
the functions do not operate as they should,
If any of the functions do not operate
next step must be entered while the
repeat the instructions from STEP3 above
as they should, enter the next 3-digit
LED is on.
to continue the Auto Search Method.
code number from the brand list.
STEP3
Point the remote control toward the
STEP4 Press the same [DEVICE] button to
STEP5 Once you have found the correct
equipment and enter the three-digit
store the code. The Device LED will
3-digit code, save it by pressing the
code number assigned to your brand
blink twice to confirm that the code
from the code tables. If there are more [AUX] button one more time. The [AUX]
has been stored.
LED light will blink twice to confirm the
than one three-digit number listed for
code was stored.
your brand, try one code number at a
D. To Identify the 3-Digit Code
time until your equipment turns off.
Programmed for a Device
F. Programming the System On/Off Button
*Note : You can verify that you have selected the
STEP1 Press the appropriate [DEVICE] button
correct code by pressing the [POWER] This allows you to program the System On/Off
and the [OK/SEL] button simultaneously
button. The equipment should turn back button so it can send up to five power On/Off
for three seconds. The device LED will
on. Then try all of the functions on the
commands with one button press.
turn on for 30 seconds. The next step
remote control (i.e. volume, mute, etc.) to
STEP1 Press the [CBL] button.
must be performed while the LED is on.
ensure you have the correct code. If any
STEP2 Press the [INFO] button. The device LED STEP2
Press the [SYSTEM ON/OFF] button
of the functions do not operate as they
will blink a number of times indicating and the [OK/SEL] button simultaneously
should, repeat the instructions from
the number of each digit for the code.
for 3 seconds. The [CBL] button will turn
STEP 3 above using the next three digit
Each digit is separated by a one second
code number from the brand list. on for 30 seconds.
interval of the LED being off.
STEP3 Press the first [DEVICE] button you want
STEP4 Store the three-digit code by pressing
Example : One blink, (pause) three blinks,
to store in the [SYSTEM ON/OFF] button
the same [DEVICE] button once
(pause) eight blinks indicates the
and then press [POWER]. Repeat this for
again. The device LED will blink twice
code number 138.
the other components you want to turn
to confirm that the code has been
*Note : Ten blinks indicates the number 0.
on/off with the [SYSTEM ON/OFF] button.
stored.
STEP4 Press the [CH ] button to save the I. Programming a 'Macro' button.
6 6 Quick Set-up Code Tables
power commands you stored. The
If your remote model has custom-programmable
TV
[CBL] button will blink twice to confirm
Macro buttons available(See Section 4), they
the commands have been saved. Quick Number
can be programmed to act as a 'Macro' or
0
Favorite Channel button in CABLE mode. This
G. Programming Volume Control 1
allows you to program up to five 2-digit channels,
2
four 3-digit channels or three 4-digit channels
Volume and Mute control are factory programmed 3
that can be accessed with one button press. 4
to automatically transfer to the respective Device
5
STEP1 Press the [CBL] button to select the CBL
mode You select, as follows: 6
mode. 7
CBL : CBL T V : TV VCR : TV
8
STEP2 Press the [MACRO] button and
DVD : TV AUX : AUX 9
[OK/SEL] button simultaneously for 3
If you wish to store the TV volume control in
VCR
seconds. The [CBL] button will turn
CBL mode, use the following steps.
Quick Number
on for 30 seconds.
STEP1 Press the [OK/SEL] button and [CBL]
0
STEP3 Enter the the 2, 3 or 4-digit code for the
button simultaneously for three 1
channel you want programmed first (for
2
seconds. The device LED will turn on
example, 007) using the Number Pad, 3
for 30 seconds. The next step must 4
then press the [STOP] button. Then
5
be performed while the LED is on.
enter the code for the next channel (for
6
7
STEP2 Press the [VOL ] button. The device example, 050), then press the [STOP]
8
button. Repeat this process for the third
LED will blink.
9
channel. The [CBL] button will blink
STEP3
Press [TV] button. The device LED will
DVD
once for each channel entered.
blink twice to confirm the programming.
STEP4 Quick Number
Press the [CH ] button to store the
*Note : To return CBL device to CBL volume
channels that were selected. The 0
repeat steps above replacing [TV] with
1
[CBL] button will blink twice to confirm
2
[CBL] in Step 3.
the storage of commands.
3
4
To access the programmed channels, press
H. Programming Channel Control
5
the [MACRO] button once. This will bring up
6
You can program the channel controls (Channel 7
the first channel. Press once again and it will
Up, Channel Down, Last and Numbers) from 8
bring up the second channel. Press again and
9
one Device to operate in another Device mode.
it will bring up the third channel.
Default channel control settings on the remote AUX
J. Low Battery Warning
control are as follows:
Quick Number
CBL : CBL T V : CBL VCR : CBL When the batteries are low and need to be 0
1
DVD : DVD AUX : AUX replaced with fresh batteries, the Device LED
2
lights will blink 2 times in sequence whenever a
3
If you wish to store the TV channel controls in
[POWER] button is pressed to turn on equipment. 4
TV mode, use the following steps.
5
6
STEP1 Press the [OK/SEL] button and [TV] button K. Memory Lock System
7
simultaneously for three seconds. The
8
This remote control is designed to retain pro-
9
device LED will turn on for 30 seconds.
grammed memory for 10 years even after bat-
The next step must be performed while
teries are removed from the remote control.
7 7
Set-up Code Tables
the LED is on.
STEP2 L. Record Your Component Set-up Codes
Press the [VOL ] button. The device CBL-CABLE Converters
LED will blink. Manufacturer/Brand
TV Set-up Code Number:
STEP3 Press [TV] button. The device LED will SCIENTIFIC ATLANTA
VCR Set-up Code Number:
PIONEER
blink twice to confirm the programming.
DVD Set-up Code Number: PACE
SAMSUNG
*Note : To return TV device to CBL channel
AUX Set-up Code Number:
MOTOROLA
repeat steps above replacing [TV] with
DIGEO
For additional information about your remote
GENERAL INSTRUMENT
[CBL] in Step 3.
control, go to www.universalremote.com
HAMLIN
CBL-CABLE Converters TV
Manufacturer/Brand Set-Up Code Number Manufacturer/Brand Set-Up Code Number
HITACHI 103 055 CROSLEY 164
JERROLD 005 004 103 005 003 008 009 010 069 CROWN 043 143
Manufacturer/Brand
MAGNAVOX 010 012 CURTIS MATHES 116 258 363 143
FUJITSU
MEMOREX 052 CXC 043
SONY MOXI 111 252 153 CYBERHOME 015
SAMSUNG NFUSION 192 DAEWOO 363 016 043 044 076 103 114 125 127 143
LG PANASONIC 044 047 DAYTRON 363 143
PHILIPS 006 012 013 020 085
TOSHIBA DELL 320 164 363
PULSAR 052
PANASONIC DIGITAL PROJECTION 570
RCA 047
PHILIPS DIMENSIA 333
REGAL 049 050
DREAMVISION 235
HITACHI
REGENCY 057
DUKANE 011 025
SHARP
SKY 230 204
DUMONT 116 073
PHILIPS
SONY 108
DURABRAND 096 052
SPRUCER 047
DWIN 257
TELNET 354
DYNASTY 043
TOCOM 039 040 056
Manufacturer/Brand DYNEX 400
TOSHIBA 052
EIKI 187
MITSUBISHI VIEWSTAR 012 015
ELECTROBAND 001
ZENITH 052 060 093 100
HP
ELECTROGRAPH 466
PHILIPS
ELECTROHOME 143 024 076 196
JVC
TV ELEKTRA 072
SAMSUNG
ELEMENT 363 494 526
PANASONIC Manufacturer/Brand Set-Up Code Number
EMERSON 028 048 043 155 005 116 363 047 050 051 076 096
PHILIPS MAGNAVOX
143 153 154 052 514
A MARK 112 143
TOSHIBA
ENVISION 116
ABEX 025
PIONEER EPSON 324 590
ACCURIAN 036
LG ESA 323
ADMIRAL 072 251 333
FISHER 007 057
ADVENT 247 388
FUJITSU 246 198 410
ADVENTURA 002
FUNAI 028 043 052
AIKO 103
Manufacturer/Brand
FUTURETECH 043
AKAI 116 146 248 404 405 473 475 323 387 391
GATEWAY 242 268
HITACHI ALBATRON 017
GE 073 116 008 009 034 056 074 155 333 363
ALERON 028
SONY
GEM 391
AMERICA ACTION 043
PHILIPS
GIBRALTER 116 073
AMPRO 073
SAMSUNG
GO VIDEO 026
AMSTRAD 052
PHILIPS MAGNAVOX
GOLDSTAR 113 116 102 363 106 112 127 143
ANAM 043 054 056 080 112
PANASONIC
GRUNPY 028 043
AOC 116 363 112 058
LG
HAIER 363 501
APEX 572
JVC
HALL MARK 363
APEX DIGITAL 006
DENON
HANNSPREE 349 381
AQUAVISION 573 574
PIONEER
HARLEY DAVIDSON 028
ASTAR 477
HARVARD 043
AUDIOVOX 076 454 388
HAVERMY 081
AVENTURA 052
HELLO KITTY 076
AVION 441
Manufacturer/Brand
HIMITSU 043
AXION 039
BOSE HISENSE 419 442
BELCOR 116
HP BELL&HOWELL 333 072 HITACHI 011 166 009 010 012 023 075 143 158 072 363 250
BENQ 423 600 587
APPLE / iPod
BOXLIGHT 266 HP 378 316 327 421
APPLE / iPod
BRADFORD 043 HUMAX 518
MICROSOFT / XBOX
BROCKWOOD 116 HYUNDAI 337 338
SONY / PS2
BROKSONIC 238 ILO 472 399
LUTRON
INFINITY 164
BYDESIGN 031 032
X-10
INFOCUS 333 230 547 548 470 532 564 595
CANDLE 116 002 003 363
ZINWELL
INITIAL 035 282
CAPEHART 058
MICROSOFT / XBOX
INSIGNIA 350 400 052 164 403 454 457
CARY AUDIO DESIGN 266
INTEQ 073
CELEBRITY 001
JANEIL 002
CENTURION 116
JBL 164
CETRONIC 043
JCB 001
CHANGHONG 247
JCPENNEY 024 116 008 009 030 065 258 143 333 363
CITIZEN 116 002 003 363 043 258 103 143
JENSEN 013
Set-Up Code Number CLARION 043
JVC 038 034 001 083 199 210 533 581
CLASSIC 043
001 003 041 042 045 046 KAWASHO 116 001
CLP CLASSIC 333
001 103 034 051 063 076 105 KEC 043
COLORTYME 116
001 005 002 KENWOOD 116 001
CONCERTO 363
001 030 KLEGG 466
CONCIERGE 073
002 111 148 KLOSS 002 059
CONTEC 043 050 051
153 KMC 143
CORNEA 116
005 103 104 KNOLL SYSTEMS 230
CORONADO 143
049 050 055 KONKA 457
CRAIG 043 054