EN 2 HTS5000W Technical Specifi cations and Connection Facilities VERSION VARIATIONS: HTS5000W/12 HTS5000W/51 Video (Yellow, Cinch) Component Video, (Y/Pb/Pr) -P-scan SCART (CVBS/RGB) Digital In - Coaxial TV In (Left/Right) Auxiliary (Left/Right) Line out (Audio)
Page 3
Technical Specifi cations and Connection Facilities HTS5000W EN 3 1. Specifi cations General: AMPLIFIER: Mains voltage : 230V for /12, /51 Output power Front : 75W RMS / channel Mains frequency : 50Hz for /12, /51 Rear : 75W RMS / channel Power consumption : 100W Center...
EN 4 HTS5000W Measurements Setup, Service Aid & Lead Free Requirements 2. Measurements Setup, Service Aid & Lead Free Requirements MEASUREMENT SETUP Tuner FM Bandpass LF Voltmeter 250Hz-15kHz e.g. PM2534 e.g. 7122 707 48001 RF Generator e.g. PM5326 S/N and distortion meter e.g.
Page 5
Measurements Setup, Service Aid & Lead Free Requirements HTS5000W EN 5 SERVICE AIDS Service Tools: Universal Torx driver holder ........4822 395 91019 Torx bit T10 150mm ..........4822 395 50456 Torx driver set T6 - T20 ......... 4822 395 50145 Torx driver T10 extended ........
Page 6
EN 6 HTS5000W Measurements Setup, Service Aid & Lead Free Requirements WAARSCHUWING WARNING Alle IC’s en vele andere halfgeleiders zijn All ICs and many other semi-conductors are gevoelig voor electrostatische ontladingen (ESD). susceptible to electrostatic discharges (ESD). Onzorgvuldig behandelen tijdens reparatie kan Careless handling during repair can reduce life de levensduur drastisch doen verminderen.
Page 7
Due to lead-free technology some rules have to be respected by the workshop during a repair: • Use only lead-free solder alloy Philips SAC305 with order code 0622 149 00106. If lead-free solder-paste is required, please contact the manufacturer of your solder-equipment.
3. Directions For Use The following except of the Quick Use Guide serves as an introduction to the set. The Complete Direction for the Use can be downloaded in different languages from the internet site of Philips Customer care Center: www.p4c.philips.com...
Page 9
Once complete, use to select a SOUND preset radio station. Refer to chapters “Wireless Receiver system” in the user manual for detailed descriptions. NEEDS HELP? Visit our website www.philips.com/support...
EN 10 HTS5000W Dismantling Instructions & Service Positions 4. Dismantling Instructions Dismantling of the PSU Board Dismantling of the Mono Board 1) Loosen 2 screws Pos 273 to remove the Transmitter 1) The disc can be manually remove by inserting a minus Board.
Page 11
Dismantling Instructions & Service Positions HTS5000W EN 11 4) Loosen 8 screws to remove Mono Board. - 2 screws Pos 262 - 1 screw Pos 265 - 1 screw Pos 268 - 1 screw Pos 264 - 1 screw Pos 267 - 2 screws Pos 269 Figure 4-7 Dismantling of the DVD LOADER...
Page 12
EN 12 HTS5000W Dismantling Instructions & Service Positions 4.5 Service Positions Mono Board Insulation Sheet PSU Board Insulation Sheet Figure 4-9 Figure 4-10 Service Position Service Position PSU Board Mono Board Insulation Sheet Front Panel Figure 4-11 Service Position Front Panel...
EN 13 Service Test Program HTS5000W Service Test Program To start service test program refers to Service Mode open the tray with remote control refers to Version or front panel key, while plugging xx refers to Software version number of BEA in the mains cord press 2, 5, 8 on (counting up from 01 to 99) remote control, the tray will close...
Page 14
EN 14 HTS5000W Service Test Program 5.1.5 Procedure to check the fi rmware version to confi rm 5.1.1 Reprogramming of DVD version Matrix upgrading After repair, the customer setting and region code may be lost. 1. Power up the set and open tray. Reprogramming will put the set back in the state in which it has left 2.
Block Diagram, Wiring Diagram HTS5000W EN 17 Block Diagram LINE SURR TV IN FRONT FRONT SUB_ SURR CENTER LEFT LEFT RIGHT RIGHT WOOFER 1501 1502 7662 +9.1V AM / FM SAA6581T RDS_Mux RDS IN Tuner TM10 RDS IC RIGHT 2422 542 00014 LEFT RDS_CK RDS_DA...
Exploded View & Module PWR 04-01 Non-Wireless HTS5000W EN 43 Introduction & defi nitions This amplifi er delivers 2 x 50 watts into 6 ohm loads. It is intended for a wireless surround system containing transmitter coupled to a DVD main set and a so called receiver-amplifi erunit. Audiotransmission is purely digital and done on 2.4Ghz with “Polaris 2”...
Exploded View & Module PWR 04-01 Non-Wireless EN 44 HTS5000W Overview of Testpoints AUDIO LEFT IN STANDBY * IN LEFT AUDIO GROUND +POWER (27Vdc) +5Vdc AUDIO RIGHT IN GROUND POWER VOL_CLK AUDIO GROUND -POWER (-27Vdc) VOL_DAT +6VDC +6VDC IN +15Vdc +3.3VDC GROUND 6Vdc -15Vdc...
Exploded View & Module PWR 04-01 Non-Wireless HTS5000W EN 45 Best condition is to start every testsequence with F16 ( Standby) and also both Mutelines F10, F11 low. This gives a minimum load startup condition. Initially, at fi rst startup, the volumechip will be on maximum attenuation (-80dB), so no sound will come out of the amplifi...
Page 46
Exploded View & Module PWR 04-01 Non-Wireless EN 46 HTS5000W Dynamic DC measurements / Mute and Standby. ( all values Vdc) Condition MODE MUTE STBY GREEN POWER LIMITS DETECT DOWN 0.25 4.22 Typical F16 low F10, F11 low Lower (Standby, muted) Higher Typical...
Page 47
Exploded View & Module PWR 04-01 Non-Wireless HTS5000W EN 47 Dynamic DC measurements - currentconsuption / Mute and Standby. ( all values mA DC) ( amplifi erpcb loaded with 100 Ohm on F6 (3.3Vdc) and 50 Ohm on F5 (6VDC) // no audio input Current Current Current...
Exploded View & Module PWR 04-01 Non-Wireless EN 50 HTS5000W Connections Connector 1100 Blue Grey (Amplifi er to Speakers) Left Right out Left + out Left - Black Black Left Right out Right – out Right + ** Since the TDA 8920B is connected “antiphase” at its right and left input, the speakers should also be connected antiphase to obtain good phase behavior.
Exploded View & Module PWR 04-01 Non-Wireless HTS5000W EN 51 Block diagram Audio amplifier board 3104 137 00173 Connector + ANALOG + POWER 1103 7110 7113 7111 AUDIO RIGHT IN TDA8920B M62429FP NJM4560 ANALOG GROUND 5100 & 2154 AUDIO RIGHT OUT AUDIO LEFT IN +6dB +30dB...
Exploded View & Module PWR 04-01 Non-Wireless EN 52 HTS5000W Mute circuitry Normal operating condition or PLAY mode: the voltage on the “mode” pin of the amplifi er TDA8920B will be 5Vdc. (level to be checked on F39) This mainly due to the resistors R3125, R3122, R3110 and saturated transistors 7106, 7102). Transistor 7104 and 7101 are not saturated at that moment.
Exploded View & Module PWR 04-01 Non-Wireless HTS5000W EN 53 ** Disconnecting the surround amplifi er from the mains results in the following: A fast mutecommand is produced by the circuitry around 7103. This helps assuring plopfree operation. At the same moment 7131 saturates and enables an extra load of 47 ohm on the 6Vdc line: result is s a clean drop-down of the 6Vdc line.
Exploded View & Module PWR 04-01 Non-Wireless EN 54 HTS5000W Volume chip M62429FP A serial driven volumechip is used in the amplifi erdesign. Control of this device is fully done by 2 lines out of the RX module. A clock and data signal is coming from pin 12 and 14 of 1103;...
Exploded View & Module PWR 04-01 Non-Wireless HTS5000W EN 55 Module PWR 04-01 Non-Wireless: Circuit Diagram (Part 1) µ 2 µ 7 µ 0 & µ 2 µ 2 & µ 2 µ 2 µ 0 µ 7 i f i : r e f i l r e i...
Exploded View & Module PWR 04-01 Non-Wireless HTS5000W EN 56 Module PWR 04-01 Non-Wireless: Circuit Diagram (Part 2) Connector + ANALOG + POWER 1103 7110 7113 7111 AUDIO RIGHT IN TDA8920B M62429FP NJM4560 ANALOG GROUND 5100 & 2154 AUDIO RIGHT OUT AUDIO LEFT IN +6dB +30dB...