Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Regency GV60
Summary of Contents for Regency GV60
-
Page 1: User Guide
GV60 REMOTE CONTROL user guide 919-713 09.20.16... -
Page 3: Table Of Contents
General Notes..................4 Coding instructions:................5 To Turn ON Appliance:................5 To Turn OFF Appliance:................. 5 Flame height adjustment............... 6 To open and close solenoid valve/burner..........6 Light / dimmer operation (not available on HRI3E/LRI3E)..... 7 Circulating Fan Operation. -
Page 4: General Notes
A code is selected automatically for this remote system from among 65,000 random codes available. Note: Wiring of valve and receiver must be completed before staring ignition. Failure to do so could damage the electronics. Overview of remote icons | GV60 user guide... -
Page 5: Coding Instructions
user guide Coding instructions: Important : The remote control/Receiver for this appliance comes pre-coded for your convenience and does not require to be re-coded after changing batteries in the hand held. As long as there is 120 volt power to the appliance and a 9 volt battery in the remote handset this will operate as normal. -
Page 6: Flame Height Adjustment
NOTE: the latching solenoid valve cannot operate manually. If the battery runs down it will remain in the last operating position. During normal operation the solenoid valve will be reset to the ON position when the unit is switched OFF remotely. | GV60 user guide... -
Page 7: Light / Dimmer Operation (Not Available On Hri3E/Lri3E)
user guide • Upon ignition Main Burner and Decorative Burner are ON. • Simultaneously press SET and (small flame) buttons to switch the Burner OFF. Printed instructions are on the battery cover. Simultaneously press SET and (large flame) button to switch Burner ON. (The AUX symbol •... -
Page 8: Modes Of Operation
- Nighttime Setback Temperature Mode • (Appliance must be in standby mode; pilot ignited.) The room temperature is measured and compared to the Nighttime Setback Temperature. The flame height is then automatically adjusted to achieve the Nighttime Setback Tem- perature. | GV60 user guide... -
Page 9: Modes Of Operation
user guide Modes of Operation • - Timer Mode (Appliance must be in standby mode; pilot ignited.) The Timers P1 and P2 (Program 1, Program 2) can each be programmed to go ON and OFF at specific time. For instructions see Timer Programming Mode. NOTE: The display shows the set temperature every 30 seconds. -
Page 10: Setting The On/Off Temperatures
Briefly press SET button to scroll to TEMP (moon) mode. Hold the SET button until • the TEMP flashes. • Press the (large flame) button to increase Nighttime Setback Temperature. • Press the (small flame) button to decrease Nighttime Setback Temperature. | GV60 user guide... -
Page 11: Setting Program Timers
user guide • Press OFF or wait to complete programming (saves automatically). Setting Program Timers • 2 ON times can be programmed per day. • CE: the day starts at 0:00, ends at 23:50 • CSA: the day starts at 12:00am, ends at 11:50pm •... -
Page 12: Setting Program Timers
Briefly press SET button to scroll to setting P2 OFF time. P2 (moon)is displayed and the time flashes. • See instructions SETTING P1 Off TIME. This concludes the programming of Timers P1 and P2. Press OFF or wait. The handset will • automatically save the changes. | GV60 user guide... -
Page 13: To Turn Off Gas Appliance
user guide To Turn Off Gas Appliance Press the OFF button on the remote to shut off the appliance • • Place ON/OFF switch, located on the appliance in the (O) OFF position. • If service is to be performed—the power must be disconnected and the gas to the unit must be shut off. - Page 14 | GV60 user guide...
- Page 15 CGV60 user guide| 15...
- Page 16 © Copyright 2016, FPI Fireplace Products International Ltd. All rights reserved.