Universal Remote Control CLIKR-5 UR5U-8780L Operating Instructions

Operating Instructions For 1 4
Introduction Button Functions
CLIKR -5
The CLIKR TM -5 UR5U-8780L & UR5U-8790L is
TM
designed to operate the CISCO / SA, Pioneer,
Pace Micro, Samsung and Motorola digital
F
set tops, Plus the majority of TV, VCR, DVD
Cable Remote Control
and AUX equipment on the market as
shown below.
CBL : Cable Set-top Box TV : Televisions
VCR : VCRs and TV/VCRs DVD: DVD Players
UR5U-8780L & UR5U-8790L
AUX : Audio Equipment, Media PC, etc.
2
Replacing Batteries
Before you program or operate the remote control,
you must install two new AA alkaline batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
MEMORY BUTTONS
STEP3 Replace the battery compartment cover.
They've been programmed by the Cable MSO
to provide quick access to the most popular channels.
5
Programming the Remote Control
3
Operations
IMPORTANT SETUP NOTE!
In this section when you are instructed to press a [DEVICE] button, that means to press either the CBL, TV, VCR,
DEFAULT STATE:
DVD or AUX button, depending on what device you are programming the remote to operate.
Device Default: Cable Set-Top Box (STB) There are three ways you can program your remote:
* Quick Setup Method
Channel Default: CABLE channel and numbers
* 3-Digit Code Method
through the CABLE STB. You have the option of
* Auto Search Method
controlling your CABLE channel and numbers
Quick Setup Method is a unique feature that enables the fastest and easiest setup by using a one digit code. This
through the TV or VCR. Refer to section H for
is the quickest way to set up devices made by popular manufacturers.
programming steps.
3-Digit Code Method allows you to setup by entering 3-digit code numbers that correspond with the compo-
Volume Default: Volume and Mute control are
nents manufacturer/brand. Code tables for this method are on the backside of the operating instructions.
automatically transferred to the respective
Component based on the Device selected: Auto Search Method scans through all of the codes in the remote control, one at a time allowing you to identi-
fy the correct code.
CBL:TV ; TV:TV ; VCR:TV. DVD:TV ; AUX:AUX.
IMPORTANT SETUP NOTE!
You have the option of controlling CABLE
Universal Remote Control, Inc.
Volume and Mute through the TV, VCR or This pertains to all programming steps. When you are in setup mode the device LED will light for 30 seconds. If you do
www.universalremote.com not press a button within 30 seconds, the LED light will turn off and exit setup mode, and you will need to start over.
AUX. Refer to section G for programming
OCE-0060L REV 17 (03/09/17)
steps.
A. Quick Setup Method VCR
Button Press Button Number
It' s easy to program the remote control to oper-
ate your TV. Simply press the number buttons 0
0 MITSUBISHI
through 9 that your TV brand is assigned to
1 HP
using the following four steps.
2 PHILIPS
3 JVC
STEP1 Manually turn on the TV you wish to
VCR&A
4 SAMSUNG
program.
Button 5 PANASONIC
STEP2 Press and hold simultaneously for 3
6 PHILIPS MAGNAVOX
seconds both the TV and A (Yellow)
7 TOSHIBA
buttons or B (Blue) buttons, based
8 PIONEER
on the column your TV brand is
9 LG
assigned to. The TV button LED light
will turn on for 30 seconds confirm-
DVD
ing that you are in the program
Button Press Button Number
mode.
0 HITACHI
STEP3 While the TV button LED is on, point
1 SONY
the remote control at the TV and
press the number button assigned to 2 PHILIPS
3 SAMSUNG
your TV brand as shown in the table
(e.g. for Sharp TV, button 5 ). The TV DVD&A 4 PHILIPS MAGNAVOX
should turn off. If it does not, press the 5 PANASONIC
Button
same number button repeatedly until
6 LG
the TV turns off. 7 JVC
8 DENON
*Note : The remote will exit the programming
TRANSPORT KEYS
9 PIONEER
mode automatically if it does not have
matching codes and the LED will turn off. AUX
Button Press Button Number
STEP4 Once the TV has turned off, press the
TV button once again to save the
0 BOSE
code. The remote control is now
1 HP
ready to control your TV.
2 ONKYO
Repeat the above steps for all other compo- 3 APPLE / iPod
nents (TV, VCR, DVD, etc.). AUX&A
4 MICROSOFT / XBOX
5 SONY / PS2
Button
*Note : If the matching code could not be found in
6 LUTRON
STEP3, use 3-Digit Code Method or Auto
7 X-10
Search Method.
8 YAMAHA
9 ROKU
Quick Set-up Code Tables
B. 3-Dight Code Method
TV
Button Press Button Number Brand
STEP1 Turn on the equipment that you want
0 RCA
the remote control to operate (Cable
1 SAMSUNG
Box, TV, VCR, DVD, etc.).
2 SONY
STEP2 Press the [DEVICE] button and the
3 LG
TV&A
4 VIZIO [OK/SEL] button simultaneously for
5 SHARP
Button three seconds. The corresponding
6 PANASONIC
device LED will turn on indicating that
7 SANYO
it is ready to be programmed. The LED
8 TOSHIBA
will remain on for 30 seconds. The
9 PHILIPS
next step must be entered while the
0 COBY
LED is on.
1 MITSUBISHI
2 HITACHI STEP3 Point the remote control toward the
3 MAGNAVOX
equipment and enter the three-digit
TV&B
4 JVC
code number assigned to your brand
Button 5 ZENITH
from the code tables. If there are more
6 INSIGNIA
than one three-digit number listed for
7 EMERSON
your brand, try one code number at a
8 WESTINGHOUSE
time until your equipment turns off.
9 TCL
*Note : You can verify that you have selected the STEP1 Press the appropriate [DEVICE] button
correct code by pressing the [POWER] and the [OK/SEL] button simultaneously
Brand
button. The equipment should turn back for three seconds. The device LED will
on. Then try all of the functions on the turn on for 30 seconds. The next step
remote control (i.e. volume, mute, etc.) to must be performed while the LED is on.
ensure you have the correct code. If any
STEP2 Press the [INFO] button. The device LED
of the functions do not operate as they
will blink a number of times indicating
should, repeat the instructions from
the number of each digit for the code.
STEP 3 above using the next three digit
Each digit is separated by a one second
code number from the brand list.
interval of the LED being off.
STEP4 Store the three-digit code by pressing
Example : One blink, (pause) three blinks,
the same [DEVICE] button once
(pause) eight blinks indicates the
again. The device LED will blink twice
code number 138.
Brand to confirm that the code has been
*Note : Ten blinks indicates the number 0.
stored.
E. Programming the AUX Device
You can take advantage of the AUX function to
C. Auto Search Method
program a devices such as a media PC, gam-
If none of the three digit code numbers
ing console or satellite radio receiver. Follow
assigned to your brand of equipment works, or
the instruction in section B to program an AUX
the code table does not list your brand, you can
device. You can also program the AUX button
use the Auto Search Method to find the correct
for a second TV, VCR or DVD player. To do this
three-digit code number for your equipment by
follow the instructions below.
following steps:
STEP1 Turn on the 5th device you want to
STEP1
Turn on the equipment that you want
program (TV, VCR, DVD, etc.).
the remote control to operate (Cable
Brand STEP2 Press the [AUX] button and the
Box, TV, VCR, DVD, etc.).
[OK/SEL] button simultaneously for 3
STEP2 Press the [DEVICE] button and the
seconds. The [AUX] device LED will
[OK/SEL] button simultaneously for
turn on for 30 seconds.
three seconds. The device LED will
STEP3
Press the [Device] button For the type of
turn on indicating that it is ready to be
device you want to setup. Point the
programmed. The LED will remain on
remote control toward the device and
for 30 seconds. The next step must be
enter the 3-digit code number assigned
entered while the LED is on.
to your brand.
STEP3 Press the [CH5] or [CH6] button one
at a time or keep it pressed. The
*Note : To program a second TV press TV, etc.
remote will emit a series of Power
STEP4 When the equipment turns off verify
ON/OFF code signals. Release the
that you have selected the correct
[CH5] or [CH6] button as soon as the
code by pressing the [POWER] button.
equipment turns off.
The equipment should turn back on.
*Note : You can verify that you have selected the
Then try all of the functions on the
correct code by pressing the [POWER]
remote control (i.e. volume, mute, etc.)
button. The equipment should turn back
to ensure you have the correct code.
on. Then try all of the functions on the
If any of the functions do not operate
remote control (i.e. volume, mute, etc.) to
as they should, enter the next 3-digit
ensure you have the correct code. If any of
code number from the brand list.
the functions do not operate as they should,
STEP5 Once you have found the correct
repeat the instructions from STEP 3 above
3-digit code, save it by pressing the
to continue the Auto Search Method.
[AUX] button one more time. The [AUX]
STEP4 Press the same [DEVICE] button to
LED light will blink twice to confirm the
store the code. The Device LED will
code was stored.
blink twice to confirm that the code
F. Programming the System
has been stored.
On/Off Button
This allows you to program the System On/Off
D. To Identify the 3-Digit Code
button so it can send up to five power On/Off
Programmed for a Device commands with one button press.
STEP1 Press the [CBL] button. *Note : To return TV device to CBL channel 6
Set-up Code Tables
repeat steps above replacing [TV] with
STEP2
Press the [SYSTEM ON/OFF] button
[CBL] in Step 3.
CBL-CABLE Converters
and the [OK/SEL] button simultaneously
I. Programming a 'Macro' button.
for 3 seconds. The [CBL] button will turn
Manufacturer/Brand
on for 30 seconds.
If your remote model has custom-programmable
MOTOROLA
STEP3 Press the first [DEVICE] button you want Macro buttons available(See Section 4), they PACE
PIONEER
to store in the [SYSTEM ON/OFF] button can be programmed to act as a 'Macro' or
SAMSUNG
and then press [POWER]. Repeat this for Favorite Channel button in CABLE mode. This
SCIENTIFIC ATLANTA/CISCO 001 003 041 042 045 046
Amino
allows you to program up to five 2-digit channels,
the other components you want to turn
ARRIS
four 3-digit channels or three 4-digit channels
on/off with the [SYSTEM ON/OFF] button. Cincinnati Bell
Digital Multimedia Technology 222
that can be accessed with one button press.
STEP4 Press the [CH5] button to save the
Duoson
STEP1 Entone
power commands you stored. The Press the [CBL] button to select the CBL
EVOLUTION
[CBL] button will blink twice to confirm mode.
Sky
TECHNICOLOR
the commands have been saved.
STEP2 Press the [MACRO] button and
WINDSTREAM
[OK/SEL] button simultaneously for 3
CBL-IPTV
G. Programming Volume Control
seconds. The [CBL] button will turn
Manufacturer/Brand
on for 30 seconds.
Volume and Mute control are factory programmed
ADB
to automatically transfer to the respective Device STEP3 Enter the the 2, 3 or 4-digit code for the
AMINO
mode You select, as follows: channel you want programmed first (for ENTONE
MOTOROLA
example, 007) using the Number Pad,
CBL : TV T V : TV VCR : TV
TV
then press the [STOP] button. Then
DVD : TV AUX : AUX
enter the code for the next channel (for Manufacturer/Brand
If you wish to store the CBL volume control in
example, 050), then press the [STOP]
A MARK
CBL mode, use the following steps.
ACCURIAN
button. Repeat this process for the third
ADMIRAL
STEP1
Press the [OK/SEL] button and [CBL]
channel. The [CBL] button will blink
AD NOTAM
button simultaneously for three ADVENT
once for each channel entered.
ADVENTURA
seconds. The device LED will turn on
STEP4 Press the [CH5] button to store the AFFINITY
for 30 seconds. The next step must AKAI
channels that were selected. The
ALBATRON
be performed while the LED is on.
[CBL] button will blink twice to confirm ALERON
AMERICA ACTION
STEP2 Press the [VOL5] button. The device
the storage of commands.
AMPRO
LED will blink.
AMSTRAD
To access the programmed channels, press
ANAM
STEP3 Press [CBL] button. The device LED will
the [MACRO] button once. This will bring up AOC
blink twice to confirm the programming. APEX
the first channel. Press once again and it will
APEX DIGITAL
bring up the second channel. Press again and AQUAVISION
*Note : To return CBL device to TV volume
ASTAR
it will bring up the third channel.
repeat steps above replacing [CBL]
AUDIOVOX
with [TV] in Step 3. AUVIO
AVENTURA
J Low Battery Warning
AVIELO
H. Programming Channel Control
AVION
When the batteries are low and need to be
AXESS
You can program the channel controls (Channel replaced with fresh batteries, the Device LED AXION
BELCOR
Up, Channel Down, Last and Numbers) from lights will blink 2 times in sequence whenever a
BELL&HOWELL
one Device to operate in another Device mode. [POWER] button is pressed to turn on equipment. BENQ
BOXLIGHT
Default channel control settings on the remote
BRADFORD
control are as follows: K. Memory Lock System BROCKWOOD
BROKSONIC
CBL : CBL T V : CBL VCR : CBL This remote control is designed to retain pro- BYDESIGN
CANDLE
DVD : DVD AUX : AUX grammed memory for 10 years even after bat-
CARY AUDIO DESIGN 266
teries are removed from the remote control. CELEBRITY
If you wish to store the TV channel controls in
CENTURION
TV mode, use the following steps. CETRONIC
L. Record Your Component Set-up Codes CHANGHONG
STEP1 Press the [OK/SEL] button and [TV] button
CIELO
Ciil
simultaneously for three seconds. The
TV Set-up Code Number:
CITIZEN
device LED will turn on for 30 seconds.
CLARION
VCR Set-up Code Number:
The next step must be performed while CLASSIC
CLP CLASSIC
the LED is on.
DVD Set-up Code Number:
COBY
COLORTYME
STEP2 Press the [VOL6] button. The device
AUX Set-up Code Number:
CONCERTO
LED will blink. CONCIERGE
For additional information about your remote
CONTEC
STEP3
Press [TV] button. The device LED will Continu-us
control, go to www.universalremote.com
CORNEA
blink twice to confirm the programming.
TV
Manufacturer/Brand Set-Up Code Number
CORONADO 143
CRAIG 043 054
Set-Up Code Number
CROSLEY 164
CROWN 043 143
002 148 206
CURTIS MATHES 116 258 363 143
001 005 002 206 217
CXC 043
001 103 034 051 063 076 105
CYBERHOME 015
001 030
DAEWOO 363 043 076 143
DAYTRON 363 143
219
DELL 320 164 363 618
172 216
DIGITAL PROJECTION 570
220
DIMENSIA 333
DREAMVISION 235
218
DUKANE 011
221
DUMONT 116 073
189 215
DURABRAND 096 052
240 241
DWIN 257
365
DYNASTY 043
212
DYNEX 400
EIKI 187
ELECTROBAND 001
Set-Up Code Number
ELECTROGRAPH 466
ELECTROHOME 143 024 076
254 ELEKTRA 072
260
ELEMENT 363 494 526 622 690
213 EMERSON 028 048 043 116 363 050 051 076 096 143 154 052 514
253
ENVISION 116
EPSON 324 590
ESA 323
Evervue 755
Set-Up Code Number
FISHER 007 057
112 143 FREEMOTION 688
FUJITSU 246 198 410
036
FUNAI 028 043 052
072 251 333
FUSION 642
672
FUTURETECH 043
247 388
002 GATEWAY 242 268
GE 073 116 008 009 034 056 333 363
680
GEM 391
116 248 404 405 473 475 323 387 391 615
GIBRALTER 116 073
017
GO VIDEO 026
028
043 GOLDSTAR 113 116 102 363 112 143
GPX 674
073
GRUNPY 028 043
052
HAIER 363 501 623 749
043 054 056 080 112
HALL MARK 363
116 363 112 616
HANNSPREE 349 381
572
HARLEY DAVIDSON 028
006 724
HARVARD 043
573 574 686
HELLO KITTY 076
477
HIMITSU 043
076 454 388
HISENSE 419 442 619 630 631 363 752
689
HITACHI 011 166 009 143 072 363 250 587 613 670
052
HP 378 316 327 421
627 628
HUMAX 518
441
HYPERION 609
711
HYUNDAI 337 338
039
ILO 472 399
116
333 072 INFINITY 164
INFOCUS 333 230 547 548 470 532 564 595 733
423 600
INITIAL 282
266
INSIGNIA 350 400 052 164 403 454 457 604 617
043
INTEQ 073
116
238 JANEIL 002
JBL 164
031 032
JCB 001
116 002 003 363
JCPENNEY 024 116 008 009 030 065 258 143 333 363
JVC 038 034 001 199 210 533 581 639 406 668 701
001
116 KAWASHO 116 001
KEC 043
043
KENWOOD 116 001
247
KLEGG 466
714
KLOSS 002
732
116 002 003 363 043 258 143 KMC 143
KNOLL SYSTEMS 230 659
043
KONKA 457
043
KREISEN 530
333
KTV 043 116 143 154
640 641 671 363
KURAZAI 072
116
LG 363 113 116 102 112 143 569 284 648 741
363
LITEON 268
073
LODGENET 072
043 050 051
LOEWE 164 738
161 746 747
LOGIK 072
116
LUXMAN 363