Sign in today to find solutions:

Don't have an account? Sign up

Raymarine ST40 User Manual

Raymarine boating equipment - marine equipment user manual.

 
Distributed by
Any reference to Raytheon or
RTN in this manual should be
interpreted as Raymarine.
The names Raytheon and RTN
are owned by the
Raytheon Company.
Next page ->

Summary of Contents

  • Page 1

    Distributed by Any reference to Raytheon or RTN in this manual should be interpreted as Raymarine. The names Raytheon and RTN are owned by the Raytheon Company.

  • Page 2

    ST40 Speed Instrument Owner’s Handbook Document number: 81157_2 Date: 1st May 2001...

  • Page 3

    Copyright © Raymarine Limited 2001...

  • Page 4

    Preface Important information WARNING Although your ST40 instrument is designed to give accurate and reliable performance, it should serve only as an aid to navigation and should never lead to the erosion of good seamanship. Always maintain a permanent watch and be aware of situations as they develop.

  • Page 5

    ST40 Speed Instrument Owner’s Handbook...

  • Page 6: Table Of Contents

    Preface Contents Important information ... i Preface ... v Chapter 1: Operation ... 1 Chapter 2: Maintenance and Fault Finding ... 5 Chapter 3: Installation ... 9 WARNING ... i EMC conformance ... i Handbook information ... i Parts supplied ... vi 1.1 Introduction ...

  • Page 7: Table Of Contents

    SeaTalk connections ... 16 Fitting the instrument ... 16 3.3 Calibration requirement ... 19 4.1 Introduction ... 21 EMC conformance ... 21 4.2 User calibration ... 21 4.3 Intermediate calibration ... 23 4.4 Dealer calibration ... 23 ST40 Speed Instrument Owner’s Handbook...

  • Page 8

    Preface Preface Thank you for purchasing a Raymarine product. We are sure your ST40 instrument will give you many years of trouble-free operation. This instrument is designed to provide reliable performance, even under the most demanding conditions.

  • Page 9

    Handbook Note: The items shown here are supplied for an ST40 Speed system. If an instrument is purchased separately, a transducer is not included. If any item is not present, contact your Raymarine Dealer. ST40 Speed Instrument Owner’s Handbook...

  • Page 10: Chapter 1: Operation, Introduction, Operating Procedures

    Chapter 4, Calibration. Coloured bezel and Desktop Mounting Bracket options are available for your ST40 instrument. Contact your Raymarine dealer for further information. 1.2 Operating procedures Operating information is presented in flow chart form. The flow charts show the various operating screens and key presses necessary to carry out the various instrument functions.

  • Page 11

    Maximum speed To reset 3 seconds Average speed To reset 3 seconds ST40 Speed Instrument Owner’s Handbook NORMAL OPERATION Switch on Water Temperature Trip Note: Screens annotated with * are temporary and will time-out to the previous permanent screen (Current speed or Water temperature) after 5 seconds.

  • Page 12: Adjusting Display Backlighting And Contrast

    Chapter 1: Operation Adjusting display backlighting and contrast Hold down for 1 second to enter Adjust Backlight mode for 2 seconds to move through Adjust Backlight mode and enter Adjust Contrast mode ADJUST BACKLIGHTING During normal operation, press for 1 second The current backlighting level is displayed.

  • Page 13

    ST40 Speed Instrument Owner’s Handbook...

  • Page 14: Chapter 2: Maintenance And Fault Finding, Maintenance, Servicing And Safety

    In order to minimise these effects and enable you to get the best possible performance from your Raymarine equipment, guidelines are given in the installation instructions, to enable you to ensure minimum interaction between different items of equipment, i.e.

  • Page 15: Instrument, Transducer, Cabling, Fault Finding, Preliminary Procedures, Fixing Faults

    This will not harm the instrument and will clear after the instrument has been switched on for a short period. Periodically clean your ST40 instrument with a soft damp cloth. Do NOT use chemical or abrasive materials to clean the instrument. Transducer Refer to the Installation and Maintenance instructions supplied with the transducer.

  • Page 16

    Chapter 2: Maintenance and Fault Finding Low battery Display blank ST40 No speed or water temperature information ST40 ST40 No speed information but water temperature information is ST40 present ST40 Action Recharge your vessel’s battery as soon as possible SPEED...

  • Page 17: Assistance

    Assistance If you are unable to rectify any problem, please contact your local Raymarine Dealer for assistance. ST40 Speed Instrument Owner’s Handbook Action Check security of SeaTalk connections between instruments. Check condition of SeaTalk cables. Isolate faulty instrument by disconnecting instruments one by one.

  • Page 18: Chapter 3: Installation, Planning Your Installation, Emc Installation Guidelines

    Chapter 3: Installation Chapter 3: Installation This chapter describes how to install the ST40 Speed instrument, and associated speed transducer. The transducer is fitted in the hull of the vessel and is connected to the rear of the instrument. 3.1 Planning your installation...

  • Page 19: Suppression Ferrites, Connections To Other Equipment, Tools Required

    If your Raymarine equipment is going to be connected to other equipment using a cable not supplied by Raymarine, a suppression ferrite MUST always be fitted to the cable close to the Raymarine unit. Tools required The tools required for fitting the standard ST40 instrument system are shown in the following illustration.

  • Page 20: Site Requirements, Transducer

    Hull material Glass reinforced plastic (GRP) Steel Aluminium Wood Other transducer types are also available for specific requirements. For further details, contact your local Raymarine dealer. Plastic through hull speed transducer dimensions 57 mm (2.25 in) 51 mm (2.0 in)

  • Page 21

    • Have 100 mm (4 in) of headroom to allow for withdrawal. The transducer should be sited within the clear water flow areas indicated by the shaded areas in the following diagram. Transducer siting ST40 Speed Instrument Owner’s Handbook Sailing vessel Planing power vessel...

  • Page 22: Procedures, Instrument, Fitting Transducer

    Chapter 3: Installation Instrument ST40 Instrument dimensions CAUTION: The presence of moisture at the rear of the instrument could cause damage either by entering the instrument through the breathing hole or by coming into contact with the electrical connectors. Each instrument must be positioned where: •...

  • Page 23: Running Transducer Cable, Connections To The Instrument

    Running transducer cable Each transducer has a 9 m (30 ft) cable fitted with spade terminals for connection to the ST40 Speed instrument. Observing the following guidelines, run the cable to the instrument: • If the cable has to be fed through the deck, always use a good quality deck gland.

  • Page 24: Stand-alone Connections

    Chapter 3: Installation Preparing wires for connection Stand-alone connections CAUTION Ensure that the power supply for each stand-alone ST40 instrument is protected by a 3 A fuse or circuit breaker. Connections to a stand-alone instrument 50 mm 4 mm 3 mm...

  • Page 25: Seatalk Connections, Fitting The Instrument

    Power cable SeaTalk bus Typical SeaTalk connections Fitting the instrument Fit your ST40 instrument as shown in the following illustrations. Remove template from handbook (immediately after index), apply to required location and mark cutting centre. ST40 Speed Instrument Owner’s Handbook...

  • Page 26

    Chapter 3: Installation Cut hole Peel protective sheets from gasket Stick gasket to rear of instrument 57 mm (2.25 in) cutter D4760-1 D4770-1 D4761-1...

  • Page 27

    Desktop Mounting Bracket An optional Desktop Mounting Bracket (Part No. E25024) enables you to mount your ST40 instrument in locations where other forms of mounting are impractical. ST40 Speed Instrument Owner’s Handbook D4819-1...

  • Page 28: Calibration Requirement

    Chapter 3: Installation D4646-1 To bracket mount your ST40 instrument, do so in accordance with the Instruction Sheet, which is included with the Desktop Mounting Bracket. 3.3 Calibration requirement Once installation is complete and before you use your instrument, carry...

  • Page 29

    ST40 Speed Instrument Owner’s Handbook...

  • Page 30: Chapter 4: Calibration, Introduction, Emc Conformance, User Calibration

    Chapter 4: Calibration Chapter 4: Calibration 4.1 Introduction The procedures in this Chapter must be carried out before the equipment is used operationally, to optimise the performance of the instrument with the vessel. Calibration information is presented in flow chart form. The flow charts show the various calibration screens and key presses necessary to carry out calibration.

  • Page 31

    Speed response screen are available only on master instruments. To save your settings and return to normal operation from any screen, hold down ST40 Speed Instrument Owner’s Handbook USER CALIBRATION for approximately 2 seconds Note: If there is no key activity when the Entry screen is...

  • Page 32: Intermediate Calibration, Dealer Calibration

    Chapter 4: Calibration 4.3 Intermediate calibration Intermediate calibration enables you to: • Check the instrument software version. • Check and if necessary set, the instrument status - either MASTR (master) or REPTR (repeater). Follow the procedure in the Intermediate calibration flow diagram. 4.4 Dealer calibration Dealer calibration enables you to set: •...

  • Page 33

    Do NOT switch the Boat Show mode on. This function must only be used for demonstration purposes. To save your settings and return to normal operation from any screen, hold down ST40 Speed Instrument Owner’s Handbook DEALER CALIBRATION During normal operation for approximately 12 seconds Entry...

  • Page 34: Instrument Specification

    Instrument Specification Instrument Specification Supply voltage: Current consumption (12 V supply): Operating temperature: Interfaces: Overall dimensions: Boss diameter: Speed range: Log range: Trip range: Water temperature reading range: Approvals: CE - conforms to 10 V to 16 V dc. 25 mA typical. 60 mA with maximum backlighting.

  • Page 35

    ST40 Speed Instrument Owner’s Handbook...

  • Page 36: Glossary

    Glossary Glossary Cal factor Calibration factor. Used in ST40 Speed and Bidata instruments to ensure the current speed reading is the actual speed. Values are from 0.25 (reduce speed reading) to 2.5 (increase speed reading). Electromagnetic Compatibility. Kilometres Per Hour.

  • Page 37

    ST40 Speed Instrument Owner’s Handbook...

  • Page 38: Index

    Index Index Average speed reset 2 Backlighting 3 Boat show mode 23 Calibration 21–24 Dealer 23–24 Intermediate 23 setting appropriate response val- ues 21–24 setting user access 24 User 21–22 Calibration requirement 1, 19 Cleaning the instrument 6 Condensation 6 Connecting the instrument 14–16 Contrast 3 Current consumption 25...

  • Page 39

    27 current 1 maximum 1 range 25 response 27 setting response 22 setting units 22 ST40 Speed Instrument Owner’s Handbook Transducer fitting 14 site requirements 11–12 Trip distance 1 Trip distance reset 2 Trip range 25 User calibration 21–22...

  • Page 42

    During this period, except for certain products, travel costs (auto mileage and tolls) up to 100 round trip highway miles (160 kilometres) and travel time of 2 hours, will be assumed by Raymarine only on products where proof of installation or commission by authorized service agents, can be shown.

  • Page 43

    Factory Service Centers United States of America Raymarine Inc 22 Cotton Road, Unit D Nashua, NH 03063-4219, USA Telephone: +1 603 881 5200 Fax: +1 603 864 4756 www.raymarine.com Sales & Order Services Telephone: +1 800 539 5539 Ext. 2333 or +1 603 881 5200 Ext.

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: