Technical Data; Declaration Of Conformity - Bosch GWS Professional 1000 Original Instructions Manual

Vibration total values a
h
determined according to EN 60745-2-3:
Surface grinding: a =8.5 m/s
h
Disk sanding: a =3.0 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This

Technical Data

Angle Grinder
Article number
Rated power input
Output power
Rated speed
Grinding disc diameter, max.
Thread of grinder spindle
Thread length (max.) of grinder spindle
Restarting Protection
Reduced starting current
Constant electronic control
Weight according to EPTA-Procedure
01/2003
– with vibration-damping auxiliary handle
– with standard-auxiliary handle
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards: EN 60745-1,
EN 60745-2-3.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 02.07.2015
Bosch Power Tools
(triax vector sum) and uncertainty K
2 2
, K=1.5 m/s ,
2 2
, K=1.5 m/s .
min
mm
mm
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
GWS 1000
3 601 H28 4..
W 1000
W 630
-1
11000
115
M 14
22


–
kg
2.2
kg 2.1
/II
Assembly
Mounting the Protective Devices
 Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales ser-
vice agent for maintenance. For addresses, see section "Af-
ter-sales Service and Application Service".
GWS 1000 GWS 1100
3 601 H28 8.. 3 601 H22 0..
1000
630
11000
125
M 14
22


–
2.3
2.1
/II
English | 19
GWS 1400
3 601 H24 8..
1100 1400
660 820
11000 11000
125 125
M 14 M 14
22 22



2.1 2.4
2.0 2.2
/II /II
1 609 92A 14D | (2.7.15)


