Sony XTL-W70 Installation Manual page 3

Installation
Before installing the
monitor
• This monitor is designed for safe operation
during driving.
• Be sure to install the unit in a suitable
position. Improper installation can cause a
serious accident.
• Be sure not to install the unit where it will
interfere with the airbag system.
Tips on the mounting location
• Choose the mounting location of the monitor
unit carefully.
• In order to prevent rattling from the vibration
of the car, make sure that the back or the
bottom of the monitor unit is touching the
mounting surface when mounting the
monitor unit.
Caution on installation
Do not install the unit:
— on a dashboard.
— in a hot place, subject to direct sunlight, near
a heater or in a car with the windows closed
(especially in summer) or in an extremely
cold place.
— in a place subject to excessive dust, moisture.
— in a place which could harm the passenger.
— in a place which could distract the driver.
— on a door or the ceiling.
Notes
• Clean the mounting surface well with the
supplied cleaning cloth. (The cleaning cloth is
a disposable type.)
• Warm the mounting surface and the double-
sided tape to a roomtemperature of more than
20 °C and then press the base of the stand
with the double-sided tape attached, firmly
against the mounting surface.
• When tightening the screws, make sure that
the nearby wiring does not get caught.
• When drilling holes on the mounting surface,
make sure that there is nothing on the other
side.
Installing the TV tuner
unit
Install the TV tuner unit under the passenger
seat or in the trunk compartment.
Avoid installing the TV tuner unit where it will
be subject to high temperatures, such as from
direct sunlight or hot air from the heater.
Installing with the hook and loop
fastener 1
Wipe off the dirt from the mounting surface.
1
安裝
顯示器安裝之前
• 顯示器是為了駕駛時的安全操作而設計的。
• 務必安裝在合適的地方，安裝不當會引發嚴重
事故。
• 顯示器的安裝務必不妨礙保險氣袋系統。
安裝位置須知
• 必須小心地選擇監視器裝置的安裝位置。
• 為防受到汽車振動影響，安裝監視器裝置時，
必須確認監視器裝置的背部或底邊是否靠住安
裝面。
安裝時須注意
不要把裝置安裝在：
— 汽車儀錶板上。
— 太熱的地方，直接照射到陽光，靠近加熱器或
密閉著車窗的汽車內（尤其是夏天）或太冷的
地方。
— 多塵，潮濕的地方。
— 會傷害到乘客的位置。
— 會阻礙駕駛者的位置。
— 車門上或汽車天花板上。
註
• 用附帶的清潔布擦乾淨安裝表面。（清潔布為
一次性使用。）
• 將安裝面和雙面黏膠帶加溫達 20℃ 以上的室
溫，然後把貼有雙面黏膠帶的基座黏貼穩在安
裝面上。
• 旋緊螺絲釘時，須留意附近的電線會被絆住。
• 在安裝面鑽孔時，也須確認背面是否有機件
等。
安裝電視機的調諧器
把電視機調諧器裝在乘客座位下或行李箱
內。
避免把調謵器裝在太陽直接照射到或有來自
加熱器熱空氣的高溫位置。
用鉤環搭扣 1 進行安裝
擦乾淨安裝面的塵垢。
1
to the mounting surface
連接到監視器表面
Installing the monitor
Make sure the installation surface and monitor
position are suitable before beginning
installation. If you cannot find a suitable
mounting location, consult your car dealer or
your nearest Sony dealer before installation.
1
Choose the mounting position, then shape
the base of the monitor stand 6 to match
the mounting surface.
Bend the base gently so there are no gaps between the
base and the mounting surface.
選定安裝位置，然後加工顯示器架底座 6，使
之與安裝面匹配。
輕輕彎折底座，使之與安裝面之間沒有間隙。
2
Clean the mounting surface well with the supplied cleaning cloth 9.
(The cleaning cloth is disposable.)
用配備的清潔布 9 仔細擦干淨安裝面（清潔布是一次性的）。
3
Peel off the protective film from the base of
the monitor stand 6 and attach the base to
the mounting surface.
Make sure the base attaches to the mounting surface
completely.
Notes
• The double-sided tape will not stick firmly if the
mounting surface temperature is less than 20 °C.
Use a hairdryer, etc. to warm up the mounting
surface before mounting.
• Consider carefully the mounting position
beforehand. If you change the position soon after
mounting the double-sided tape will be weakened.
• When removing the monitor stand, preheat the
mounting surface with a hairdryer then slowly peel
up to remove.
剝去顯示器架底座 6 的保護薄膜，把底座貼合
於安裝面。
要確保底座完全貼在安裝面上。
註
• 安裝面的溫度如果是低於 20℃，雙面黏膠帶便可能
不能黏貼牢。安裝前，請用吹風機等給安裝面加熱一
下。
• 須預先仔細地考慮過安裝位置。一旦黏貼上了而又改
變安裝位置時，雙面黏膠帶的黏著性將會減低。
• 要卸下監視器架時，請用吹風機加熱一下安裝面，然
後緩緩地剝開黏膠面把它卸下來。
4
Fix the stand with the supplied screws 7.
Note
Before drilling holes in the mounting surface, make
sure there is nothing behind the dashboard.
用所配備的螺釘 7 固定顯示器架。
註
安裝面鑽孔前要確保儀表板後沒有任何東西。
5
Attach the supplied plastic cover 8 over the
base of the monitor stand.
把配備的塑料罩 8 貼在顯示器架底座上。
6
Adjust the height.
When the monitor is at the right height, tighten the
clamp. To keep the monitor from rattling while
driving, make sure the back or bottom of the monitor
is resting firmly on the mounting surface.
調整高度
當顯示器處於正確高度時緊定.夾箍。汽車行駛中顯示
器不得有卡嗒聲，其背部或底部務必穩固地抵靠安裝
面。
7
Adjust the angle.
Loosen the lever and adjust the angle. After this
adjustment, tighten the lever to fix the angle.
調整角度
旋松支杆並調整角度，調好後，旋緊支杆以固定角度。
安裝顯示器
開始安裝前應確信安裝面和顯示器位置是合
適的。如果您找不出適當的位置，可在安裝前向
您的汽車經銷商或就近向 Sony 經銷商咨詢。
6
7
7
8
Clamp
儀表板
Lever
支杆