Battery Information; Battery Voltage Display; Clearing Memory; Error Code Description - Schlage KING COBRA-2 Programming Manual

PROGRAMMING GUIDE
It is highly recommended that the programming code be
changed for maximum security. It can be changed to a
different 5-6 digit code or to an iButton, if desired.
Codes and iButtons can be
deleted using these steps. It
is required that the PIN be
used to delete an iButton,
therefore it is necessary to
keep a record of the PINs
associated with each iButton.

BATTERY INFORMATION:

The KC5100-2/KC5500-2 uses four, standard AA ALKA-
LINE batteries.The KC9000-2 uses four AAA ALKALINE
batteries. The batteries should provide enough life for
approximately 80,000 lock/unlock cycles (40,000 for the
KC9000-2). When the battery voltage gets down to
approximately 4.4VDC, the lock provides low battery indi-
cation as follows: when a code/iButton is entered, the red
LED will flash twelve times before the lock executes the
command. This is an indication that it is time to replace
the batteries. The lock will continue to operate for approx-
imately 500 cycles in this condition. When the battery
voltage gets down to approximately 4.3VDC, the lock will
go into "Low Battery Lockout" mode. A Freeze/Lockout
code must be entered to gain access. If the batteries are
not changed, the lock will eventually cease to function
and the mechanical key override must be used.

BATTERY VOLTAGE DISPLAY:

You can find out how much voltage is left in your batteries
by doing the following:
1. Enter Programming Code, press
**
2. Enter 11
> The LEDs will blink indicating battery voltage:
- Red LED indicates unit volts (left of decimal point).
- Green LED indicates tenths of a volt.
(Example: If the red LED blinks 5 times and then the
green LED blinks 3 times, this indicates that the battery
voltage is approximately 5.3VDC.)
The pattern of blinking LEDs repeats 3 times.
FORM 67050
TO DELETE
CODES/iBUTTONS
* *
PROG. CODE & OR iBUTTON
* *
5
* *
ENTER CODE/PIN
* *
TO DELETE MORE
* *
TO END
*
PAGE 3
KING COBRA-2: 12 BUTTON WITH BEEPER
TO CHANGE
PROGRAMMING CODE
* *
PROG. CODE & or iBUTTON
* *
7
* *
ENTER NEW
PROG.CODE
* *
ENTER NEW
PROG.CODE AGAIN
To change relock time fol-
low these step. Relock
time can be adjusted from
1 to 240 seconds.

CLEARING MEMORY:

Clearing memory will delete all programmed codes and
iButtons and restore factory default codes. The program-
ming code or iButton will also be deleted and the default
programming code will be restored. The factory default
relock time delay will also be restored. If the memory
ever needs to be erased follow the steps below:
1. Remove the inside escutcheon.
2. Remove one battery.
*
3. Press and hold the
4. Reinstall the battery.
> Red LED flashes 2 times.
> Green LED illuminates and beeper sounds.
*
4. Release the key.
5. Reinstall the inside escutcheon.

ERROR CODE DESCRIPTION

(Note: the beeper does not sound during error code indication.)
2 Code too long 6 digits max.
3 Memory full, must delete some codes.
4 Can not delete Programming code - use Change steps.
5 Second entry did not match first (Programming Code).
6 Invalid entry, start over. (Verify that any codes entered prior to this
error do not operate the lock.)
7 Code to be deleted does not exist.
8 Code too short - 3 digits minimum (or 5 digit for Programming Code).
9 Duplicate code, code already exists.
10 Manual Programming is disabled.
12 Lockout mode
TO CHANGE TO
PROGRAMMING iBUTTON
* *
PROG. CODE & or iBUTTON
7
ENTER NEW PROG.
iBUTTON
TO CHANGE RELOCK
TIME DELAY
(DEFAULT 3 SEC.)
* *
PROG. CODE & or iBUTTON
99
1
PRESS 1 FOR 1
SEC. AND/OR 5
FOR 5 SEC. THE
TIMES WILL ADD.
* *
TO END
key.
* *
* *
* *
1
5
2/07