Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Corsair Manuals
  4. Computer Hardware
  5. H105
  6. Quick start manual

Corsair H105 Quick Start Manual

Hydro series. extreme-performance 240mm liquid cpu cooler
Hide thumbs Also See for H105:

Advertisement

Quick Links

Download this manual See also: Quick Start Manual
QUICK START GUIDE
EXTREME-PERFORMANCE 240MM LIQUID CPU COOLER
TM
Replacing the Colored Accent Ring
• To replace the colored accent ring, use a small flathead
screwdriver to pry out the default metallic grey ring at
three corners, located as shown in figure 1.
• Then merely press the replacement ring of choice into
place, as shown in figure 2.
figure 1
/
figure 2

Advertisement

loading

Related Manuals for Corsair H105

Summary of Contents for Corsair H105

  • Page 1 Replacing the Colored Accent Ring • To replace the colored accent ring, use a small flathead screwdriver to pry out the default metallic grey ring at three corners, located as shown in figure 1. • Then merely press the replacement ring of choice into place, as shown in figure 2.

  • Page 2: Included Hardware

    LGA 2011 STANDOFF x1 RETENTION RING x8 LONG FAN SCREWS x4 LGA 115X / 1366 STANDOFF (PRE-INSTALLED) x4 AMD BLACK STANDOFF x4 THUMBSCREWS x2 SP120L FANS Note: The H105 comes with Intel mounting bracket pre-installed on the pump for quick installation.
  • Page 3 Installing the Intel Backplate LGA 1366 • For LGA 115X installation, slide the backplate pins inside. (figure 1) • For LGA 1366 installation, slide the backplate pins outside. (figure 1) • Install the assembled backplate. (figure 2) Note: Intel LGA 2011 does not require back plate installation.
  • Page 4 Installing the Intel Stando Screws Installing the Fans and Radiator • Attach the provided Intel stando . Attach the radiator and the fans as shown. For the best LGA 115X/1366 cooling performance, we recommend mounting the fans • Use (B) for LGA 115X / 1366, or (C) for as an air-intake to your PC case.
  • Page 5 Installing the Pump Unit Connect Power to the Fans and Pump • Align the bracket and pump over the stando • Connect the pump power cable to any available 3-pin or screws as shown. 4-pin fan header on the motherboard. (figure 1) •...
  • Page 6 LGA 2011 STANDOFF x1 RETENTION RING x8 LONG FAN SCREWS x4 LGA 115X / 1366 STANDOFF (PRE-INSTALLED) x4 AMD BLACK STANDOFF x4 THUMBSCREWS x2 SP120L FANS Note: The H105 comes with Intel mounting bracket pre-installed on the pump for quick installation.
  • Page 7 Installing the AMD Stando Screws • Remove the stock AMD top mounting bracket(s) shown. (figure 1) • Attach the provided AMD stando . (figure 2) • Tighten all four screws until firmly secure. (figure 2) Note – The stock AMD motherboard backplate is used for AMD installation.
  • Page 8 Installing the AMD Mounting Bracket figure 1 Note: The Intel mounting bracket must be removed from the pump before installing the AMD mounting bracket. • Remove the retention ring from the bottom of the pump. (figure 1) • The retention ring is held on by four clips; press the clips in one at a time until all four are release to remove the retention ring.
  • Page 9 Installing the Fans and Radiator Installing the Pump Unit • Align the bracket and pump over the stando Attach the radiator and the fans as shown. For the best screws as shown. cooling performance, we recommend mounting the fans as an air-intake to your PC case. •...
  • Page 10 Connect Power to Fans and Pump • Connect the pump power cable to any available 3-pin or 4-pin fan header on the motherboard. (figure 1) • Connect the included Y-header cable to any available 3-pin or 4-pin fan header. (figure 1) •...