Advertisement
KX-TGA523CE_OI 04.4.28 11:32 ページ 2
Getting Started
1-F Battery Charge
CHARGE Indicator
•Recharge the battery when:
2-A)
– "Recharge battery" is displayed on the handset,
– "
" flashes, or
– the handset beeps intermittently while it is in use.
•If the battery has been discharged, the handset will display "Charge
for 6 HRS" and "
charger. The handset will not work unless the battery is charged.
Continue charging.
1-G Handset Registration
This handset must be registered to a KX-TG5200C/
SET]
KX-TG5202C/KX-TG5230C/KX-TG5240C/KX-FPG391C base unit.
1-H)
The handset will be assigned an extension number at registration.
N/OFF]
The KX-TGA523C will not work without one of the following
)
Panasonic cordless phone systems: KX-TG5200C/KX-TG5202C/
KX-TG5230C/KX-TG5240C/KX-FPG391C.
Only one handset can be registered at a time.
Make sure the base unit and the other handsets are not being used.
Have both the handset and base unit nearby during registration.
et
CHARGE Indicator
60 Hz)
*LOCATOR Button
•Base unit model shown here is KX-TG5240C.
*
The location of LOCATOR button varies by base unit model.
KX-TG5200C/KX-TG5202C: LOCATOR [
KX-TG5230C/KX-TG5240C/KX-FPG391C:
[LOCATOR/INTERCOM/TRANSFER]
1-H Setting Time
The charger unit has a 12-hour clock (monthly accuracy
seconds). After the AC adaptor is connected, "
display. Follow the steps to set the clock.
[+, -, TUNE/CLOCK]
•If a power failure occurs, the display will show "
10 minutes, then it will become blank. After power returns, "
will be displayed. The clock memory will be lost. Set the clock. The
radio alarm and buzzer alarm memory will be retained for about
10 minutes during a power failure (4-A, 4-B).
Place the handset on the charger and charge
for 6 hours before initial use. Repeat
charging will require approximately the same
amount of charging time (6 hours) if the
battery is depleted completely.
•The unit beeps once, the CHARGE indicator
lights and "Charging" is displayed.
•When the battery is fully charged, "Charge
completed" is displayed if there are no
new calls in the Caller List.
" when you place the handset on the
[-]
Press LOCATOR
on base unit
for 3 sec.
Then press OK
BACK
BACK
FRANÇ.
FRAN
OK
OK
Soft Key (
)
OK
], [
], [
], [
±
30
" flashes on the
[OFF]
[TIME SET]
" for about
Battery information
After your Panasonic battery is fully charged, you can expect the
following performance:
Operation
While in use (TALK)
While not in use (Standby)
While using Clarity Booster feature
•Clean the charge contacts of the handset and the charger with a
soft, dry cloth once a month. Clean more often if the unit is
subject to grease, dust or high humidity, otherwise, the battery
may not charge properly.
A nickel metal hydride battery that is recyclable
powers the product you have purchased. Please call
1-800-8-BATTERY for information on how to recycle
this battery.
The handset display shows the
instructions as shown on the right.
1
Base unit: Press and hold the
*LOCATOR button for 3 seconds.
•The CHARGE indicator flashes. After the CHARGE indicator
starts flashing, the rest of the procedure must be completed
within 1 minute.
•On the KX-FPG391C, "HS REGISTRATION" is displayed.
2
Handset:
#Press the soft key (
$Wait until a long beep sounds and the
display shows the new extension number.
•Registration is complete.
•The registered number "[1]" to "[4]" is shown on the top right of
the display.
•You can stop registration by pressing [OFF] on the handset and
pressing the *LOCATOR button on the base unit.
•To cancel the handset's registration, please see your base unit
Operating Instructions.
•If you try to register this handset to the KX-TG6500C base unit,
"Wrong handset Refer to manual" is displayed. The base
units for this handset are mentioned above.
•To change the display language from English to French on the
] or [
]
handset, press [MENU][0][8][2], then press the soft key (
•To change the display language from French to English on the
handset, press [MENU][0][8][1], then press the soft key (
1
Press [TIME SET].
2
Adjust the time by pressing
[+, TUNE/CLOCK] or [–, TUNE/CLOCK].
•Pressing [+] or [–] increases or
decreases the time in one-minute units.
•Pressing and holding [+] or [–]
increases or decreases the time faster.
3
Press [TIME SET] to set the clock.
•The time stops flashing.
"
•You can exit time setting mode any time by pressing [OFF].
Section 1
Operating time
Up to 5 hours
Up to 11 days
Up to 3 hours
Press LOCATOR
on base unit
for 3 sec.
Then press OK
FRANÇ.
e.g. Extension number 2
).
SP
PRIVACY
OK
Handset [2]
Registered
SAUV.
SAVE
e.g. 3:30PM is set.
O K
[
2
]
).
).
Advertisement
