HotSpring GGE Owner's Manual page 9

with this information. See Water Quality and Maintenance for more
information.
IMPORTANT: Watkins Manufacturing Corporation does not
recommend that the spa be filled with "softened" water, as this may
damage the spa's equipment.
• Purchase the Clean Screen
™
contaminants from the tap water. This is recommended, not required.
DON'T:
• Power up the spa until it has been filled with water! Power to the
spa automatically activates critical components within the spa, such
as controls, heater, circulation pump, and other systems. If power
is supplied to these components prior to the spa being filled, the
components will be damaged, and this may result in a non-warranty
component failure.
DON'T:
• Fill the spa with hot water or cold water with cold water temperature
below 10º C (50º F)! Tripping of the high-limit thermostat may result
causing your spa to stop functioning.
DON'T:
• Use your spa after filling until all of the steps listed below START-UP
are completed!
• Add chlorine if treating your spa with polyhexamethylene biguanide
(Biguanide, PHMB, eg. BaquaSpa
START-UP
Your HOT SPRING spa has been thoroughly tested during the
manufacturing process to ensure reliability and long-term customer
satisfaction. A small amount of water may have remained in the
plumbing after testing and, as a result, may have spotted the spa shell
or the spa siding prior to delivery. Before filling the spa, wipe the spa
shell clean with a soft rag.
The following instructions must be read and followed exactly to ensure
a successful start-up or refill.
1. CLOSE ALL DRAINS AND FILL THE SPA
the filter compartment. Your HOT SPRING spa water level should be
maintained approximately 4 cm above the top of the highest jet.
2. AFTER THE SPA HAS BEEN FILLED
equipment compartment door is secured, power must be applied to
the spa.
3. TO CHECK THE OPERATION OF THE JET SYSTEM
purge any remaining air from the heating system:
GRANDEE & ENVOY Models:
• Push the JETS icon on the Home Screen.
• Push the double jet icons to run the jet pumps on high speed for
one minute.
• Press the OFF icon (far right) once the jet system is full operational
(as indicated by strong, non-surging jets), priming of the spa is
complete, to shut the jets off.
VANGUARD, ARIA, SOVEREIGN, TRIUMPH, PRODIGY &
JETSETTER Models:
• Push the JETS hardbutton once.
• Push the JET MAX or JET soft button to make jet pump(s) run on
high speed for one minute.
Getting Started
pre-filter to remove unwanted
® ) sanitizer.
with water through
with water and the
• Press the ALL OFF soft button once the jet system is full operational
(as indicated by strong, non-surging jets), priming of the spa is
complete, to shut the jets off.
Weak or surging jets are an indication of a low water level condition or
clogged filter
IMPORTANT: Be sure the COMFORT CONTROL Levers (see
illustration in Spa Features section) are open by turning each one
clockwise and checking to see that the SMARTJET lever is pointing
in the
4. USING A TEST STRIP AND APPLICABLE CHEMICALS
adjust Total Alkalinity (TA) to 80 ppm, Calcium Hardness (CH)
to 100 ppm, then spa water pH to between 7.4 and 7.6. These
procedures are listed in the "Water Quality and Maintenance"
section.
IMPORTANT: Always add spa water chemicals directly into the
filter compartment with the jet pump on high speed for at least
ten minutes. Adjusting the Total Alkalinity (TA) as the first step is
important, as out-of-balance TA will affect your ability to adjust the
pH correctly and will prevent the sanitizer from operating effectively.
5. SUPERCHLORINATE THE SPA WATER
teaspoons of chlorine (sodium dichlor) per 950 liters (250 gallons)
of spa water. Press the Clean Cycle icon (on home screen)
for GRANDEE & ENVOY models and press the soft button
next to CLEAN (on the home screen) for VANGUARD, ARIA,
SOVEREIGN, TRIUMPH, PRODIGY & JETSETTER models to
circulate the spa water for a ten-minute period.
6. DURING THE SUPER-CHLORINATION PERIOD
SMARTJET lever(s) through both operating positions, letting the
spa water circulate (with jets on) for equal periods of time. The HOT
SPRING spa's SMARTJET levers are designed to operate in the 3
o'clock and 9 o'clock positions.
7. SET THE TEMPERATURE CONTROL
pre-programmed to reach 38° C (100°F), and will normally do so
within 18 to 24 hours. You may raise the water temperature by:
GRANDEE & ENVOY M
• Press the temperature window in the Home Screen to display
the Set Temperature Screen.
• Press
VANGUARD, ARIA, SOVEREIGN, TRIUMPH, PRODIGY &
JETSETTER Models:
• Pressing the OPTIONS hard button on the control panel.
and to
• Pressing the soft button next to Temperature.
• Pressing the soft button next to TEMP ▲ button on the control
panel to raise the temperature.
• Pressing the soft button next to TEMP ▼ button on the control
panel to lower the temperature.
Place the vinyl cover on the spa and allow the water temperature
to stabilize. Make sure you secure the cover in place using the
cover locks. Periodically check the spa water temperature. When
Page 6
the water temperature climbs above 32°C (90°F), proceed to the
next step.
To prevent tampering, you can lock your desired temperature
cartridges.
position.
:
odels
or to change the water set temperature.
,
by adding 1½
, rotate the
, the spa is
Page 6