Advertisement
Quick Links
TIMETRAX™ SYNC RF ETHERNET TRANSMITTER
Installation Instructions 9T1WI, S9DWXSLAUB
OVERVIEW
Thank you for choosing a TimeTrax™ Sync RF Wireless Clock System. The TimeTrax™ RF Wireless Clock System
receives dependable, accurate time from the TimeTrax™ Sync RF Wireless Transmitter.
TimeTrax™ Sync Wireless RF Transmitters capture main time source from Network Time Protocol (NTP) server or GPS
to ensure a reliable time signal with no FCC license required. The transmitters use dependable frequency-hopping
technology to continuously broadcast a time signal to an unlimited number of TimeTrax™ Sync RF Wireless analog or
digital wall clocks with no interference.
additional signal coverage is required, an unlimited number of secondary transmitters may be added (part #
S9DSXOLAUB or 42337 sold separately).
The transmitters may also be used to transmit synchronization signals from a designated time source to TimeTrax™
Sync Bell/Tone System or TimeTrax™ Time Clock terminals.
For more information, visit pyramidtimesystems.com or call our technical support team at 888.479.7264 during
regular business hours: 8am-5pm EST, M-F.
1
Dependent upon facility construction & contents.
ANTENNA INSTALLATION
Remove contents from box and attach supplied antenna to top of transmitter by rotating in clockwise
direction.
IMPORTANT: Using anything other than included Power Supply or included Antenna in a vertical
orientation may be unsafe, cause improper operation, and violates FCC regulations.
ETHERNET
I2256
Page 1 of 5
888.479.7264
pyramidtimesystem.com
1
Each transmitter supports up to 250,000 sq. ft. of signal coverage. If
Advertisement
Related Manuals for Pyramid TIMETRA SYNC RF 9T1WI
Summary of Contents for Pyramid TIMETRA SYNC RF 9T1WI
- Page 1 TIMETRAX™ SYNC RF ETHERNET TRANSMITTER Installation Instructions 9T1WI, S9DWXSLAUB OVERVIEW Thank you for choosing a TimeTrax™ Sync RF Wireless Clock System. The TimeTrax™ RF Wireless Clock System receives dependable, accurate time from the TimeTrax™ Sync RF Wireless Transmitter. TimeTrax™ Sync Wireless RF Transmitters capture main time source from Network Time Protocol (NTP) server or GPS to ensure a reliable time signal with no FCC license required.
- Page 2 TIMETRAX™ SYNC RF ETHERNET TRANSMITTER Installation Instructions 9T1WI, S9DWXSLAUB LOCATION Choose appropriate location to install transmitter. If using a GPS Time Source, allow 50 ft cable reach. If facility is 250,000 sq ft or less, locate the transmitter centrally or in the case of multi-story facilities, locate the transmitter on the middle floor (see diagram below).
-
Page 3: Installation
TIMETRAX™ SYNC RF ETHERNET TRANSMITTER Installation Instructions 9T1WI, S9DWXSLAUB INSTALLATION Place or mount transmitter so antenna is positioned vertically. This is required for optimum performance. Connect CAT-5E Ethernet cable (sold separately) into ETHERNET port located on transmitter. Connect free end of CT-5E cable into Ethernet switch or computer. Connect power cable into POWER port on transmitter. -
Page 4: Specifications
TIMETRAX™ SYNC RF ETHERNET TRANSMITTER Installation Instructions 9T1WI, S9DWXSLAUB SPECIFICATIONS NTP Server or GPS Signal Receiver Time Souce 902-928MHz (128 channels) Frequency Range Transmission 9T1WI (Shelf Mount) Approx. 250,000 sq ft Coverage Power Input 120/240VAC <4 Watt RF Power Output 12 VDC, 1.5 Amp. -
Page 5: Warranty
Failure caused by accident, alteration, misuse or improper packaging of returned unit is not covered by this Warranty. Any repair to equipment other than by Pyramid voids the Warranty. Users in territories other than USA, Canada, South America & Australia should contact the Dealer from whom the unit was purchased. The rights under this Warranty are limited to original user and may not be transferred to subsequent users.