Vauxhall ASTRA Owner's Manual page 256

10.8b ... and remove the multi-function
display unit from the surround panel
Refitting
9 Refitting is a reversal of removal.
Multi-function display unit
(Zafira models)
Removal
10 Remove the front ashtray.
11 Undo the two lower mounting screws, and
unclip the heater/air conditioning control
panel from the facia.
12 Unclip the hazard warning switch, TC
(Traction Control) switch, and seat heating
switch from the control panel and disconnect
the wiring .
13 Unclip the heater/air conditioning unit
from the panel.
14 Remove .the steering wheel as described
in Chapter '10. Note that this procedure
includes disconnecting the battery.'
15 Undo the screws and remove the steering
column shrouds and tilt lever knob,
16 Release the clips and slide the wiper and
indicator switches from the steering column .
17 Remove the radio as described in Sec-
tion 17.
18 Remove the lighting and foglight switch as
described in Section 4.
19 Unclip the fusebox cover from the facia.
20 Using a screwdriver through the grille
slots, undo the outer vent securing sc'rew and
remove the vent.
21 Undo the screws securing the instrument
panel surround to the facia. There are three
located directly above the instrument panel,
one either side of the steering column, and
one at each lower corner of the surround.
22 Withdraw the surround from the facia , and
at the same time slide the lighting switch from
its guide. Disconnect the wiring from the
mUlti-function display unit (see illustration),
then release the remaining wiring from the
rear of the surround.
23 Unclip the multi-function display unit from
the surround.
Refitting
24 Refitting is a reversal of removal.
Outside temperature sensor
Removal
25 With the bonnet open, reach down behind
10.22 Disconnecting the wiring from the
multi-function display unit
the front bumper and disconnect the wiring
from the sensor located inside the front
bumper.
26 Twist the sensor and unclip it from the
front bumper (see illustration).
Refitting
27 Refitting is a reversal of removal.
Coolant temperature sensor
Removal and refitting
28 Refer to Chapter 3, Section 7.
Coolant residue sensor
Removal
29 The coolant residue sensor is located on
the base of the coolant expansion tank. Refer
to Chapter 3 and partially drain coolant from
the system until the coolant level is below the
sensor, then remove the expansion tank and
disconnect the wiring from the sensor.
30 With the expansion tank inverted, use a
screwdriver to release the sensor.
Refitting
31 Refitting is a reversal of removal.
Windscreen washer fluid level
sensor
Removal
32 The sensor is located beneath the left-
hand end of the front bumper. First remove
the bumper as described in Chapter 11 ,
33 Disconnect the wiring from the sensor
located on the reservoir.
11.2a Undo the screws ...
Body electrical systems 12-15
10.26 Removing the outside temperature
sensor from the front bumper
34 Carefully prise the sensor from the,
reservoir.
Refitting
35 Refitting is a reversal of removal.
Engine oil Ie,vel sensor
Removal
36 Remove the sump as described in the
relevant Part of Chapter 2.
37 . Prise the retaining ring from the sump.
38 Press the sensor connection out of the
sump.
39 Unbolt the sensor from the sump and
remove the sealing ring.
Refitting
40 Refitting is a reversal of removal, but use a
new sealing ring. Refit the sump with
reference to Chapter 2,
11 Cigarette lighter -
removal and refitting
Removal
1 Unclip the panel located below the ashtray,
2 With the ashtray open, undo the screws
and withdraw it from the centre console,
Disconnect the wiring from the cigarette
lighter (see illustrations),
3 Remove the heater coil, then remove the
bulbholder and cover from the rear of the unit
(see illustrations).
11.2b ... remove the. ashtray and
disconnect the wiring
12
...
~~ ---~~'
..--
~ ~---------