Daikin ERGA04DAV3A Installer's Reference Manual page 104

8/10
Field settings table
Breadcrumb Field code Setting name
9.I [4-09] Which power limitation type is required?
9.I [4-0A] Backup heater configuration
9.I [4-0B] Automatic cooling/heating changeover hysteresis.
9.I [4-0D] Automatic cooling/heating changeover offset.
9.I [5-00] Is backup heater operation allowed above equilibrium temperature during space
heating operation?
9.I [5-01] What is the equilibrium temperature for the building?
9.I [5-02] Space heating priority.
9.I [5-03] Space heating priority temperature.
9.I [5-04] Set point correction for domestic hot water temperature.
9.I [5-05] What is the requested limit for DI1?
9.I [5-06] What is the requested limit for DI2?
9.I [5-07] What is the requested limit for DI3?
9.I [5-08] What is the requested limit for DI4?
9.I [5-09] What is the requested limit for DI1?
9.I [5-0A] What is the requested limit for DI2?
9.I [5-0B] What is the requested limit for DI3?
9.I [5-0C] What is the requested limit for DI4?
9.I [5-0D] Backup heater voltage
9.I [5-0E] --
9.I [6-00] The temperature difference determining the heat pump ON temperature.
9.I [6-01] The temperature difference determining the heat pump OFF temperature.
9.I [6-02] What is the capacity of the booster heater?
9.I [6-03] What is the capacity of the backup heater step 1?
9.I [6-04]
What is the capacity of the backup heater step 2?
9.I [6-05] --
9.I [6-06] --
9.I [6-07] What is the capacity of the bottom plate heater?
9.I [6-08] What is the hysteresis to be used in reheat mode?
9.I [6-09] --
9.I [6-0A] What is the desired comfort storage temperature?
9.I [6-0B] What is the desired eco storage temperature?
9.I [6-0C] What is the desired reheat temperature?
9.I [6-0D] What is the desired DHW production type?
9.I [6-0E] What is the maximum temperature setpoint?
9.I [7-00] Domestic hot water booster heater overshoot temperature.
9.I [7-01] Domestic hot water booster heater hysteresis.
9.I [7-02] How many leaving water temperature zones are there?
9.I [7-03] --
9.I [7-04] --
9.I [7-05] Boiler efficiency
9.I [8-00] Minimum running time for domestic hot water operation.
9.I [8-01] Maximum running time for domestic hot water operation.
9.I [8-02] Anti-recycling time.
9.I [8-03] Booster heater delay timer.
9.I [8-04] Additional running time for the maximum running time.
9.I [8-05] Allow modulation of the LWT to control the room temp?
9.I [8-06] Leaving water temperature maximum modulation.
Final English - Tanslations in progress
4P495257-1A - 2017.11
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W (*2)
R/O (*1)
(*3)
R/W
R/W
R/W
R/W
R/O (*1)
R/W (*2)
(*3)
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
(#) Setting is not applicable for this unit.
Range, step
Default value
0: Current
1: Power
0: 1 (*1)
1: 1/1+2 (*2) (*3)
2: 1/2
3: 1/2 + 1/1+2 in emergency
1~10°C, step: 0,5°C
1°C
1~10°C, step: 0,5°C
3°C
0: Allowed
1: Not allowed
-15~35°C, step: 1°C
0°C
0: Disabled
1: Enabled
-15~35°C, step: 1°C
0°C
0~20°C, step: 1°C
10°C
0~50 A, step: 1 A
50 A
0~50 A, step: 1 A
50 A
0~50 A, step: 1 A
50 A
0~50 A, step: 1 A
50 A
0~20 kW, step: 0,5 kW
20 kW
0~20 kW, step: 0,5 kW
20 kW
0~20 kW, step: 0,5 kW
20 kW
0~20 kW, step: 0,5 kW
20 kW
0: 230V, 1~ (*1) (*2)
1: 230V, 3~ (*2)
2: 400V, 3~ (*3)
1
2~40°C, step: 1°C
25°C
0~10°C, step: 1°C
2°C
0~10kW, step: 0,2kW
3kW
0~10kW, step: 0,2kW
2kW (*2)
3kW (*1)(*3)
0~10kW, step: 0,2kW
0kW (*1)
4kW (*2)
6kW (*3)
0
0
0~200W, step: 10W
0W
2~20°C, step: 1°C
10°C
0
30~[6-0E]°C, step: 1°C
60°C
30~min(50, [6-0E])°C, step: 1°C
45°C
30~min(50, [6-0E])°C, step: 1°C
45°C
0: Reheat only
1: Reheat + sched.
2: Scheduled only
(*4) : 40~75°C, step: 1°C
60°C [E-07]=0
(*4) : 40~80°C, step: 1°C
80°C [E-07]=5
(*5) : 40~60°C, step: 1°C
60°C
0~4°C, step: 1°C
0°C
2~40°C, step: 1°C
2°C
0: 1 LWT zone
1: 2 LWT zones
2.5
0
0: Very high
1: High
2: Medium
3: Low
4: Very low
0~20 min, step 1 min
1 min
5~95 min, step: 5 min
30 min
0~10 hour, step: 0,5 hour
0,5 hour [E-07]=1
3 hour [E-07]≠1
20~95 min, step: 5 min
50 min
0~95 min, step: 5 min
95 min
0: No
1: Yes
0~10°C, step: 1°C
5°C
Installer setting at variance with
default value
Date Value
(*1) *3V_(*2) *6V_
(*3) *9W_(*4) *HB*_
(*5) EHV*_
(*6) *X*_(*7) *H*