Related Manuals for Planet IFGS-1022HPT
Summary of Contents for Planet IFGS-1022HPT
- Page 1 Industrial 8-Port 10/100TX 802.3at PoE+ 2-Port Gigabit TP/SFP Combo Ethernet Switch IFGS-1022HPT User’s Manual...
-
Page 2: Table Of Contents
4. Troubleshooting ..................19 APPENDIX A: Networking Connection ..............20 A.1 PoE RJ45 Port Pin Assignments (End-span) ..........20 A.2 Switch’s RJ45 Pin Assignments ..............20 A.3 RJ45 Cable Pin Assignments ..............21 A.4 Fiber Optic Cable Connection Parameter ..........22 APPENDIX B: Approved PLANET SFP Transceivers ..........23... -
Page 3: Package Contents
1. Package Contents Thank you for purchasing PLANET industrial 8-Port 10/100TX 802.3at PoE+ + 2-Port Gigabit TP/SFP combo Ethernet Switch, IFGS-1022HPT. In the following section, the term “Industrial PoE+ Switch” means the IFGS-1022HPT. Open the box of the Industrial PoE+ Switch and carefully unpack it. The box... -
Page 4: Hardware Introduction
2.1 Physical Dimensions Dimensions (W x D x H): 161 x 107 x 72mm Front View Top View Extended Standard P2 FAULT 1000 1A@24V Side View PoE In-Use 802.3at PoE+ IFGS-1022HPT Side View Bottom View Dimensions ( unit = mm ) -
Page 5: Switch Front Panel
PoE In-Use 802.3at PoE+ IFGS-1022HPT Figure 2-1: IFGS-1022HPT Front Panel Fast Ethernet TP interfaces (Port 1 to port 8) 10/100BASE-TX copper, RJ45 twisted-pair: Up to 100 meters. Gigabit TP Interfaces (Port 9 to port 10 TP/SFP Combo Interfaces) 10/100/1000BASE-T copper, RJ45 twisted-pair: Up to 100 meters. - Page 6 DIP Switch The Industrial PoE+ Switch has a built-in solid DIP switch that provides “Standard” and “Extend” operation modes. The Industrial PoE+ Switch operates as a normal IEEE 802.af/at PoE+ Switch in the “Standard” operation mode. In the “Extend” operation mode, the Industrial PoE+ Switch operates on a per- port basis at 10Mbps full duplex operation but can support 30-watt PoE power output over a distance of up to 250 meters overcoming the 100m limit on Ethernet UTP cable.
-
Page 7: Led Indicators
2.3 LED Indicators System Color Function Green Lit: indicates power 1 has power. Green Lit: indicates power 2 has power. FAULT Lit: indicates neither power 1 or power 2 has no power. Per 802.3at PoE+ 10/100BASE-TX Interface (Port 1 to Port 8) Color Function Lit: indicates the link through that port is successfully... -
Page 8: Switch Upper Panel
2.4 Switch Upper Panel The upper panel of the Industrial PoE+ Switch consists of one terminal block connector within two DC power inputs. Figure 2-2 shows the upper panel of the Industrial PoE+ Switch. 1A@24V 1 2 3 4 5 6 Figure 2-2: Industrial PoE+ Switch Upper Panel 2.5 Wiring the Power Inputs The 6-contact terminal block connector on the top panel of Industrial PoE+ Switch... -
Page 9: Wiring The Fault Alarm Contact
2. Tighten the wire-clamp screws for preventing the wires from loosening. Power 1 Fault Power 2 1. The wire gauge for the terminal block should be in the range between 12 and 24 AWG. 2. The DC power input range is 48V ~ 56V DC. Note 2.6 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the... -
Page 10: Product Features
2.7 Product Features Physical Port „ Eight 10/100BASE-TX Fast Ethernet RJ45 ports with IEEE 802.3at/af PoE+ Injector (Port-1 to Port-8) „ Two 10/100/1000BASE-T Gigabit Ethernet RJ45 ports (Port-9 and Port-10) „ Two 1000BASE-X mini-GBIC/SFP slots for SFP type auto detection (Port-9 and Port-10) ... -
Page 11: Product Specifications
2.8 Product Specifications Product IFGS-1022HPT Hardware Specifications Eight 10/100BASE-TX RJ45 auto-MDI/MDI-X ports Fast Ethernet Copper Ports (Port-1 to Port-8) Two 10/100/1000BASE-T RJ45 auto-MDI/MDI-X Gigabit Ethernet Copper Ports ports (shared with Port-9 and Port-10) Two 1000BASE-SX/LX/BX SFP interfaces (shared SFP/mini-GBIC Slots with Port-9 and Port-10) Eight ports with 802.3af/802.3at PoE+ injector... - Page 12 Removable 6-pin terminal block Pin 1/2 for Power 1 Connector Pin 3/4 for power fault alarm Pin 5/6 for Power 2 One relay output for power failure. Alarm Alarm relay current carry ability: 1A @ 24V AC 48~56V DC, 5.5A (max.) Power Requirements (>51V DC for PoE+ output recommended)
- Page 13 IEC 60068-2-32 (free fall) Stability Testing IEC 60068-2-27 (shock) IEC 60068-2-6 (vibration) IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab Gigabit 1000BASE-T Standards Compliance IEEE 802.3z Gigabit SX/LX IEEE 802.3x Flow Control and Back Pressure IEEE 802.3af Power over Ethernet IEEE 802.3at Power over Ethernet Plus Environment Operating Temperature...
-
Page 14: Installation
DIN-rail and wall. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. This following picture is telling the user how to install the device, and the device is not IFGS-1022HPT. Note 3.1 DIN-rail Mounting Installation The DIN-rail is screwed on the Industrial PoE+ Switch when out of factory. - Page 15 Step 2: Lightly insert the bottom of the switch into the track. Step 3: Make sure if the DIN-rail is tightly secured on the track. Step 4: Please refer to the following procedures to remove the Industrial PoE+ Switch from the track. Step 5: Lightly pull out the bottom of the switch for removing it from the track.
-
Page 16: Wall-Mount Plate Mounting
3.2 Wall-mount Plate Mounting To install the Industrial PoE+ Switch on the wall, please follow the instructions described below. Step 1: To remove the DIN-Rail from the Industrial PoE+ Switch, loosen the screws to remove the DIN-rail. Step 2: Place the wall mount plate on the rear panel of the Industrial PoE+ Switch. -
Page 17: Installing The Sfp Transceiver
MGB Series Transceiver Figure 2-3: Plug-in the SFP Transceiver PLANET Industrial PoE+ Switch supports 1000Mbps mode with both single mode and multi-mode SFP transceivers. 1. Before we connect Industrial PoE+ Switch to the other network device, we have to make sure both sides of the SFP transceivers are with the same media type, for example, 1000BASE-SX to 1000BASE-SX, 1000BASE-LX to 1000BASE-LX. -
Page 18: Removing The Transceiver Module
4. Check the Link mode of the SFP port if the link fails. It is recommended to use PLANET SFPs on the Industrial PoE+ Switch. If you insert an SFP transceiver that is not supported, the Industrial PoE+ Switch will not recognize it. -
Page 19: Troubleshooting
4. Troubleshooting This chapter contains information to help you solve issues. If the Industrial PoE+ Switch is not functioning properly, make sure the Industrial PoE+ Switch was set up according to instructions in this manual. Q1: The per port LED is not lit Solution: Check the cable connection of the Industrial PoE+ Switch. -
Page 20: Appendix A: Networking Connection
APPENDIX A: Networking Connection A.1 PoE RJ45 Port Pin Assignments (End-span) PIN NO RJ45 POWER ASSIGNMENT Power + 1 2 3 4 5 6 7 8 Power + Power - Power - A.2 Switch’s RJ45 Pin Assignments 1000Mbps, 1000BASE-T Contact MDI-X BI_DA+ BI_DB+... -
Page 21: Rj45 Cable Pin Assignments
A.3 RJ45 Cable Pin Assignments The standard RJ45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight-through cable and crossover cable connection: Straight Cable SIDE 1 SIDE 2 1 = White/Orange... -
Page 22: Fiber Optic Cable Connection Parameter
A.4 Fiber Optic Cable Connection Parameter The wiring details are shown below: 1000X Fiber Optic Cables: Standard Fiber Type Cable Specifications 1000BASE-SX Multi-mode 50/125μm or 62.5/125μm (850nm) Multi-mode 50/125μm or 62.5/125μm 1000BASE-LX (1300nm) Single-mode 9/125μm Wiring Distances: Diameter Modal Bandwidth Max. Distance Standard Fiber (micron) (MHz * km) (meters) 62.5... -
Page 23: Appendix B: Approved Planet Sfp Transceivers
APPENDIX B: Approved PLANET SFP Transceivers The following list of approved PLANET SFP transceivers is correct at the time of publication: Gigabit SFP Transceiver Modules MGB-GT SFP-Port 1000BASE-T Module - 100m MGB-SX SFP-Port 1000BASE-SX mini-GBIC module - 550m MGB-SX2 SFP-Port 1000BASE-SX mini-GBIC module – 2km... - Page 24 MGB-TL70 SFP-Port 1000BASE-LX mini-GBIC module - 70km (-40~75°C) SFP-Port 1000BASE-LX (WDM, TX:1310nm) mini-GBIC module - MGB-TLA10 10km (-40~75°C) SFP-Port 1000BASE-LX (WDM, TX:1550nm) mini-GBIC module - MGB-TLB10 10km (-40~75°C) SFP-Port 1000BASE-LX (WDM, TX:1310nm) mini-GBIC module – MGB-TLA20 20km (-40~75°C) SFP-Port 1000BASE-LX (WDM, TX:1550nm) mini-GBIC module - MGB-TLB20 20km (-40~75°C) SFP-Port 1000BASE-LX (WDM, TX:1310nm) mini-GBIC module -...