Related Manuals for Neilsen CT2217
Summary of Contents for Neilsen CT2217
- Page 1 2000LB DUMP CART CT2217 Instruction & Assembly SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE...
-
Page 2: Ec Declaration Of Conformity
In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. Product description: DUMP CART Model: CT2217 Applicable EC Directives: EC Machinery Directive 2006/42/EC 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K. -
Page 3: Safety Rules
SAFETY RULES Remember, any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times when using power equipment. CAUTION: VEHICLE BRAKING LOOK FOR THIS SYMBOL TO POINT OUT STABILITY MAY BE AFFECTED WITH THE IMPORTANT SAFETY PRECAUTIONS. -
Page 4: Hardware Pack
HARDWARE PACK... -
Page 5: Assembly Instructions
ASSEMBLY INSTRUCTIONS IMPORTANT: Due to the weight of the cart, we recommend that you have someone assist you in lowering the cart onto its wheels after it has been assembled. CAUTION DO NOT LEAVE THE CART UNATTENDED IN UPRIGHT POSITIONDURING ASSEMBLY.A FALLING CART CAN CAUSE PERSONAL INJURY.PAY CLOSE ATTENTION TO THE STABILITY OF THE CART WHILE IT REMAILN IN AN UPRIGHT POSITION.FOR BEST STABILITY,ASSEMBLE ON A SMOOTH,LEVEL SURFACE. - Page 6 12. Connecting the 2 wheel supports by eight M8X20 Hex Bolts, Flat Washer Ø8, Lock Washer Ø8 and M8 Nuts. FIGURE 3 FIGURE 4 13. Assemble the axle through the wheel support as shown in Figure 5. 14. Apply grease to the ends of the axle now or use a grease gun after the wheels are assembled. 15.
- Page 7 FIGURE 7 FIGURE 8 23. Assemble two corner caps to the front of the cart using four M6X16 round head bolts , Ø6 lock washer, Ø6 Flat Washer and M6 hex nuts. Tighten. See Figure 9. 24. Assemble the tie rod to the axle spindles using two M12X30 hex bolts, four Ø12 flat washer and two M12 hex lock nuts, Tighten, leavind ollse enough that the spindles still pivot.
- Page 8 FIGURE 12 FIGURE 11 30. To lower the cart onto its wheels you should: a：Ghock the rear wheels as shown in Figure 13.b:Get the assistance of another person to help you lower the cart onto it’s wheels. 31. Assemble the two pivot bars to the front tongue section using four M8X20 hex bolts, Ø8 lock washer, Ø8 Flat Washer and M8 hex nuts.
-
Page 9: Operation
OPERATION CAUTION：VEHICLE BRAKING AND STABILITY MAY BE AFFECTED WITH THE ADDITION OF AN ACCESSORY OR AN ATTACHMENT.BE AWARE OF CHANGING CONDITIONS ON SLOPS. 1. Refer to the vehicle owners manual for instruction on safe operation on slops. 2. For best handling and traction, distribution the weight of the load evenly in the cart. 3. - Page 10 Parts Drawing & Parts List...
- Page 11 Parts Drawing & Parts List PART # DESCRIPTION PART # DESCRIPTION Cart Bed Hex Bolt M8x65 Front Panel Tie Rod Corner Hex Bolt M12x30 Screw M6x16 Wheel Support Lock Washer Ø6 Front Axle Support Hex Nut M6 Cotter Pin Ø3x30 Tailgate Guide Hex Bolt M10x100 Tailgate...
- Page 12 CANNON TOOLS LTD 20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K. Made in China...