Related Manuals for Westinghouse PT20115
Summary of Contents for Westinghouse PT20115
- Page 1 INSTRUCTION MANUAL HAMMER DRILL PT20115 0~2,900 Note : Before operating or installing this hammer drill, read this manual and follow all safety rules and operating instructions.
-
Page 3: General Power Tool Safety Warnings
GENERAL POWER TOOL SAFETY WARNINGS WARNING ： Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. - Page 4 GENERAL POWER TOOL SAFETY WARNINGS b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is in the o -position before connecting to power source and/or battery pack, picking up or carrying the tool.
-
Page 5: Specific Safety Rules
GENERAL POWER TOOL SAFETY WARNINGS f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. - Page 6 SPECIFIC SAFETY RULES 10. Only use accessory bit in good condition. 11. Keep your hands away from under the work-piece. 12. Periodically check that all nuts, screws and other fixings are properly tightened. 13. Rags, cloths, cord, string and the like should never be left around the work area.
- Page 7 9. Forward/reverse lever 4. Depth gauge 10. Adjustment knob for auxiliary handle 5. Indicator light 11. Auxiliary handle 6. ON/OFF switch Technical Specification: PT20115 Model Rated voltage / frequency 120V/60Hz Rated power No load speed (r/min) 0-3000 Max. Chuck size Φ13mm...
- Page 8 PREPARATION AND ADJUSTMENT • Release the ON/OFF switch to stop the tool. • Press the lock-on button (7) when the ON/OFF switch (6) is completely depressed if the continuous operation is required. • Press the trigger switch then release it to disengage the lock-on button. •...
- Page 9 • Checking the depth: check the depth with a steel rule for most accurate measure- ment and then turn the adjustment knob (2) to tighten the auxiliary handle in the required position. For Proper Operations • Hold the drill with your first two fingers on the on/o switch. •...
- Page 10 • Begin drilling at a very low speed to prevent the bit from slipping o the starting point. Increase the speed as the drill bit bites into the material. • When drilling through holes, place a block of wood behind the work-piece to prevent ragged or splintered edges on the back side of the hole.
-
Page 11: Cleaning And Maintenance
CLEANING AND MAINTENANCE Wipe the drill using a well-wrung cloth after use and always keep the surface and ventilation holes free of dirt. Never use corrosive or abrasive detergents, as they may attack the plastic parts of the machine. Replacing carbon brushes For safety reasons, the machine automatically switches o if the carbon brushes are so worn out that they no longer have contact with the motor. -
Page 12: Part List
PART LIST NO. Description Cant. screw M5X18 spring washer drill chuck 13mm output spindle key 3X3.7X10 circlip for hole 32 dust cover woolen ring ball bearing 6002-2Z 10 screw ST4.2X40 gear box 12 circlip for shaft 13 gear 14 circlip for shaft 15 Impact spring 16 Impact gear(static) 17 bearing 608-2Z... - Page 13 PART LIST NO. Description Cant. 31 cable pressplate 32 auliminium sleeve 33 rating label 120V 34 stator 120V 35 screw ST4.2X60 36 air ba e 37 bearing cover 38 ball bearing 60-2Z 39 brush holder 40 carbon brush 120V 41 terminal 42 brush cover 43 armature 120V 44 screw ST3X6...
-
Page 14: Exploded View
EXPLODED VIEW...