Rs-232C] - Panasonic PT-MZ670 Operating Instructions Manual

[COMMAND]
[POWER ON]
[STANDBY]
[QUICK STARTUP]
[SHUTTER]
[INPUT]
[LIGHT POWER]
[IN STANDBY MODE(AUDIO)]
[VOLUME]
*1 [MIRRORING] is displayed when the optional Wireless Module (Model No.: ET-WM300) is attached.
*2 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, its input
name is automatically reflected from [INPUT1] to [INPUT10]. When an item that does not reflect the input name is selected, it will be disabled.
11) Press the <ENTER> button.
f The command is fixed and n is displayed at the left of the selected command.
f After the command is fixed, press the <MENU> button to close the detailed setting screen.
12) Press asqw to select [STORE], and press the <ENTER> button.
Note
f To delete a command that has been already set, press the <DEFAULT> button on the remote control while the screen in Step 5) is
displayed, or select [DELETE] at the screen in Step 6) and press the <ENTER> button.
f If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
f The operating time will be the local time. (x page 117)
f If an operation is executed with the remote control or control panel of the projector or with a control command before the command set in
[SCHEDULE] is executed, the command set with the schedule function may not be executed.

[RS-232C]

Set the communication condition of the <SERIAL IN> terminal. Refer to "<SERIAL IN> terminal" (x page 213).
1) Press as to select [RS-232C].
2) Press the <ENTER> button.
f The [RS-232C] screen is displayed.
3) Press as to select [INPUT SELECT].
4) Press qw to switch the item.
[PROJECTOR]
[DIGITAL LINK]
Chapter 4 Settings — [PROJECTOR SETUP] menu
Detailed settings of
[COMMAND]
―
―
[ON]
[OFF]
[OPEN]
[CLOSE]
[RGB1]
[RGB2]
[VIDEO]
[HDMI1]
[HDMI2]
[DIGITAL LINK]
[MEMORY VIEWER]
[Panasonic APPLICATION]
[MIRRORING]
*1
[INPUT1] - [INPUT10]
*2
[NORMAL]
[ECO]
[QUIET]
[OFF]
[ON]
[0] - [63]
Performs the RS-232C communication with the <SERIAL IN> terminal of the projector.
Performs the RS-232C communication via the optional DIGITAL LINK output supported device (Model
No.: ET-YFB100G, ET-YFB200G) and the <DIGITAL LINK/LAN> terminal.
Description
Switches on the projector.
Enters standby.
Enables the function of the [PROJECTOR SETUP] menu → [ECO
MANAGEMENT] → [QUICK STARTUP].
Disables the function of the [PROJECTOR SETUP] menu → [ECO
MANAGEMENT] → [QUICK STARTUP].
Disables the shutter function (shutter: open).
Enables the shutter function (shutter: closed).
Switches the input to RGB1.
Switches the input to RGB2.
Switches the input to VIDEO.
Switches the input to HDMI1.
Switches the input to HDMI2.
Switches the input to DIGITAL LINK.
Switches the input to MEMORY VIEWER.
Switches the input to Panasonic APPLICATION.
Switches the input to MIRRORING.
Switches the input to DIGITAL LINK, and switches the input of the
Panasonic twisted-pair-cable transmitter to the specified input.
Prioritizes luminance.
Controls the power to increase the life of the light source although
the luminance is lower than that of [NORMAL].
Prioritizes the operation with less noise although the luminance is
lower than that of [NORMAL].
Stops the audio output during standby.
Outputs the audio during standby.
Sets the volume.
ENGLISH - 119