Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zte ZXHN H168NW
Summary of Contents for Zte ZXHN H168NW
-
Page 1: User Manual
ZXHN H168NW User Manual... - Page 2 ZTE Corporation. ZTE CORPORATION reserves the right to modify this manual for product upgrade or other causes without...
- Page 3 Limited warranty ZTE warrants that, for one year from the date of delivery by ZTE to purchaser's designated carrier, the Equipment will remain free from defects in design, material and workmanship under normal use and service and will conform in all material respects to the applicable specifications set forth in purchase order or agreement;...
- Page 4 Equipment serviced in breach of this sentence. End User shall have no right to reject, return, or receive a refund for any Equipment from ZTE. Any item repaired or replaced by ZTE shall continue to be warranted for the longer of the remainder of the original warranty period or 90 days from the date the repaired or replaced part is delivered to the carrier.
- Page 5 ZXHN H168NW User Manual ZTE SHALL NOT BE LIABLE FOR ANY LOSS OF PROFITS OR INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM OR ARISING OUT OF OR IN CONNECTION WITH USING OF THIS PRODUCT, WHETHER OR NOT ZTE HAD BEEN ADVISED, KNEW OR SHOULD HAVE...
- Page 6 ZXHN H168NW User Manual terms herein, the Equipment and all ZTE documentation is ZTE Confidential Information.
-
Page 7: Table Of Contents
Contents Chapter 1 Safety Instructions............1 1.1 Safety Checklist ..............1 1.2 Safety Instructions............... 1 Chapter 2 Overview ................3 2.1 Features ................3 2.2 Product Specifications ............3 2.3 Packing List ................ 4 2.4 System Requirements ............4 Chapter 3 Installation Preparations ..........6 3.1 Hardware Description ............ -
Page 8: Chapter 1 Safety Instructions
Chapter 1 Safety Instructions 1.1 Safety Checklist Check the following items before installing the ZXHN H168NW VDSL2 equipment. 1. Electrical Safety Do not place inflammable, conductive or /wet objects around the equipment. Cables should be in good condition. All electrical appliances should be placed stably. - Page 9 ZXHN H168NW User Manual Unplug the power cables during thunderstorms to protect the equipment from lightning strikes. Clean the equipment by using a soft and dry cloth. Power off the equipment before cleaning it. Power off the idle equipment.
-
Page 10: Chapter 2 Overview
Chapter 2 Overview The ZXHN H168NW is a VDSL2 and GE access device that supports multiple line transmission modes. At the user end, it provides four 10/100/1000Base-T Ethernet interfaces, one USB 2.0 Host port, and the wireless high 400mW power. With the... -
Page 11: Packing List
Note: Information provided above is for reference only; actual external view of the product may vary. Note: The power adapter used for the ZXHN H168NW must match. 2.4 System Requirements Please check the following items before installing the ZXHN H168NW. - Page 12 ZXHN H168NW User Manual If you have subscribed to the VDSL2 service, your VDSL2 operator will provide you at least one valid IP address through static allocation or dialup dynamic allocation. 2. Computer Configuration Please make sure that the system is equipped with a 10M/100M Ethernet adapter and supports the TCP/IP protocol.
-
Page 13: Chapter 3 Installation Preparations
Chapter 3 Installation Preparations 3.1 Hardware Description Front Panel Figure 3.1-1 Front Panel of the ZXHN H168NW Table 3.1-1 Descriptions of the LEDs on the Front Panel Identification Color Status Description Power off. POST: Power on and Red On self-testing... - Page 14 ZXHN H168NW User Manual Identification Color Status Description The system is in Bridge mode (DSL/GE) has not been connected. The data packets are Green passing through Flash router interface on the WAN side. The system is in the Route mode and the...
- Page 15 ZXHN H168NW User Manual Identification Color Status Description wireless port enabled. Data being transmitted. The flashing Flash Green frequency indicates the WLAN WLAN traffic speed. equipment powered wireless port is disabled. The WPS function is off. The WPS function is in Flash negotiation status.
- Page 16 ZXHN H168NW User Manual Rear Panel Figure 3.1-2 Rear Panel of the ZXHN H168NW Left Panel Figure 3.1-3 Left Panel of the ZXHN H168NW...
- Page 17 ZXHN H168NW User Manual Table 3.1-2 Description of Interfaces on the Rear Panel and Left Panel Item Specifications RJ-11 interface: The equipment is connected to the VDSL2 by a network line or a splitter through a telephone line. RJ-45 interface: It is connected to a PC or other network devices by a network cable.
-
Page 18: Hardware Connections
ZXHN H168NW User Manual 3.2 Hardware Connections Introduction: 1. Use a RJ-11 cable to connect the line port of the splitter to the RJ-11 port (the phone jack) on the wall. 2. Use another RJ-11 cable to connect the modem (or VDSL2) port of the splitter with the line port of the gateway. - Page 19 PHONE (or TEL): Connects the phone sets. The installation process is as follows: 1). Connects the line interface of the ZXHN H168NW to the Modem (or VDSL2) interface of the splitter by using one RJ-11 telephone cable. 2). Connects the phone set lines to the Phone (or TEL) interface of the splitter.
- Page 20 Check cable connections as described below: 1. Check the VDSL2 cable connection If the DSL LED is on when the ZXHN H168NW is power on, it indicates that the VDSL2 line is properly connected. (Generally it takes one to two minutes to complete the VDSL2 connection).
-
Page 21: Appendix A Faqs
All indicators are off after the ZXHN H168NW equipment is powered on. First, make sure that you have plugged the power adapter of the ZXHN H168NW into a working power socket and that the ZXHN H168NW has been powered on (the switch button is pressed down). - Page 22 ZXHN H168NW User Manual Problem and Troubleshooting Solution: First, check whether the ZXHN H168NW is at normal state (check the indicators against this User Manual). If yes, check the computer or application network, not the VDSL2. If the VDSL2 Modem has problems, then check the status of indicators one by one to debug the fault.
- Page 23 ZXHN H168NW User Manual Problem and Troubleshooting What are the reasons for VDSL2 synchronization failure (also referred to link down or link establishment failure)? When the VDSL2 suddenly fails to be synchronized (link down) during application, it might be caused by the DSL indicator of the Modem, which is not constantly On.
- Page 24 ZXHN H168NW User Manual Problem and Troubleshooting 5. When the VDSL2 still fails to be synchronized after the VDSL2 Modem has been connected to the incoming customer cable end, contact the operator to check whether there are external line failures/modem failures.
- Page 25 ZXHN H168NW User Manual Problem and Troubleshooting This problem may be caused by the following reasons: 1. The account has expired or it is a default account. In such cases, pay the charge. 2. In case a subscriber changes his or her residence.
- Page 26 ZXHN H168NW User Manual This equipment complies with FCC radiation exposure limits set forth for uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- Page 27 ZXHN H168NW User Manual Customer Information This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On bottom of this equipment is a label that contains, among other information, a product identifier of US: ZTEDL01BHNH168NW. If requested, this number must be provided to the telephone company.
- Page 28 ZXHN H168NW User Manual Connection to party line service is subject to state tariffs. Contact the state public utility commission public service commission or corporation commission for information. If the telephone company requests information on what equipment is connected to their lines, inform them of: The telephone number that this unit is connected to, The ringer equivalence number [0.1B ]...