Tout défaut de le faire pourrait entraîner des blessures graves. Poulan PRO 1030 Stevens Creek Road Augusta, GA 30907 545186805 Rev. 2 Instruction Manual PP3816AV / PP4218AV PP4218AVL Poulan PRO 850 Matheson Blvd. West...
IDENTIFICATION OF SYMBOLS WARNING! This chain saw can be dangerous! Careless or improper use can cause serious or even fatal injury. Always wear appropriate ear protection, eye protec- tion and head protection. Always use two hands when operating the chain saw. WARNING! ject should be avoided;...
S Keep fuel and oil caps, screws, and fas- teners securely tightened. S Use only Poulan PRO accessories and re- placement parts as recommended. HANDLE FUEL WITH CAUTION S Do not smoke while handling fuel or while operating the saw.
wood closes in and pinches the moving saw chain in the cut along the top of the guide bar and the saw chain is suddenly stopped. This sudden stopping of the chain results in a reversal of the chain force used to cut wood and causes the saw to move in the opposite direction of the chain rotation.
Page 5
WARNING: The following features are included on your saw to help reduce the hazard of kickback; however, such features will not totally eliminate this danger. As a chain saw user, do not rely only on safety de- vices. You must follow all safety precau- tions, instructions, and maintenance in this manual to help avoid kickback and other forces which can result in serious injury.
MODEL PP3816AV 952044942 PP4218AV / PP4218AVL 952044926 NOTE: If this saw is to be used for com- mercial logging, a chain brake is required and shall not be removed or otherwise dis- abled to comply with Federal OSHA Regula- tions for Commercial Logging. WARNING: The engine exhaust from this product contains chemicals known...
Adjusting Screw Tensioning Rack 4. Slide guide bar on bar bolts until guide bar stops against clutch drum sprocket. Bar bolts Guide bar 5. Carefully remove the chain from the pack- age. Hold chain with the drive links as shown. Tip of CUTTERS MUST FACE IN DIIRECTION OF ROTATION...
guide bar. DO NOT operate the saw if the chain is loose. NOTE: The chain is tensioned correctly when the weight of the chain does not cause it to sag below the guide bar (with the chain saw sitting in an upright position), but the chain still moves freely around the guide bar.
Page 9
Poulan or Poulan PRO oil resists high temperature thinning. If Poulan or Poulan PRO bar and chain oil is not available, use a good grade SAE 30 oil. S Never use waste oil for bar and chain lubri- cation.
When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope re- wind slowly. For cold weather starting, start the unit at FULL CHOKE;...
Page 11
CAUTION: The chain brake must be checked several times daily. The engine must be running when performing this proce- dure. This is the only instance when the saw should be placed on the ground with the en- gine running. Place the saw on firm ground. Grip the rear handle with your right hand and the front han- dle with your left hand.
remove them before making the notch. If us- ing saw to remove buttress roots, keep saw chain from contacting ground to prevent dull- ing of the chain. NOTCH CUT AND FELLING THE TREE S Make notch cut by cutting the top of the notch first.
First cut on compression side of log Second cut Second cut First cut on compression side of log BUCKING WITHOUT A SUPPORT S Overcut through of the diameter of the log. S Roll the log over and finish with a second overcut.
If any dealer other than an authorized service dealer performs work on the product, Poulan PRO may not pay for repairs under warranty. It is your re- sponsibility to maintain and perform general maintenance.
each 5 hours of operation. Remove Sawdust From Guide Bar Groove Oil Holes S Burring of guide bar rails is a normal process of rail wear. Remove these burrs with a flat file. S When rail top is uneven, use a flat file to re- store square edges and sides.
The spark plug should be replaced each year to ensure the engine starts easier and runs better. Ignition timing is fixed and non- adjustable. 1. Loosen 3 screws on cylinder cover. 2. Remove the cylinder cover. 3. Pull off the spark plug boot. 4.
Follow the mix instructions found on stabilizer containers. Run engine at least 5 minutes after adding stabilizer. Poulan/WEED EATER 40:1, 2-cycle engine oil (air cooled) is blended with fuel stabilizer. If you do not use this oil, you...
HELPFUL TIP During storage of your gas/ oil mixture, the oil will sepa- rate from the gas. We recommend that you shake the gas can weekly to insure proper blending of the gas and oil. ENGINE S Remove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening.
Poulan PRO for this chain saw. This war- ranty does not cover tune- -up, spark plugs, filters, starter ropes, chain sharpening, bars, chains, and other parts which wear and re- quire replacement with reasonable use dur- ing the warranty period.
Page 20
PARTS: The use of add- -on or modified parts can be grounds for disallowing a warranty claim. Poulan PRO is not liable to cover fail- ures of warranted parts caused by the use of add- -on or modified parts. HOW TO FILE A...