Table of Contents
Advertisement
Using a support stand
nd
2
Cut
st
1
st
1
nd
2
Cut
LIMBING AND PRUNING
WARNING:
Be alert for and guard
against kickback. Do not allow the moving
chain to contact any other branches or ob-
jects at the nose of the guide bar when limb-
ing or pruning. Allowing such contact can re-
sult in serious injury.
WARNING:
Never climb into a tree
to limb or prune. Do not stand on ladders,
platforms, a log, or in any position which can
cause you to lose your balance or control of
the saw.
IMPORTANT POINTS
S Work slowly, keeping both hands firmly
gripped on the saw. Maintain secure foot-
ing and balance.
S Watch out for springpoles. Springpoles are
small size limbs which can catch the saw
chain and whip toward you or pull you off bal-
ance. Use extreme caution when cutting
small size limbs or slender material.
S Be alert for springback. Watch out for
branches that are bent or under pressure.
Avoid being struck by the branch or the
saw when the tension in the wood fibers is
released.
S Keep a clear work area. Frequently clear
branches out of the way to avoid tripping
over them.
LIMBING
S Always limb a tree after it is cut down. Only
then can limbing be done safely and prop-
erly.
S Leave the larger limbs underneath the
felled tree to support the tree as you work.
S Start at the base of the felled tree and work
toward the top, cutting branches and
limbs. Remove small limbs with one cut.
S Keep the tree between you and the chain.
Cut from the side of the tree opposite the
branch you are cutting.
S Remove larger, supporting branches with
the cutting techniques described in BUCK-
ING WITHOUT A SUPPORT.
S Always use an overcut to cut small and
freely hanging limbs. Undercutting could
cause limbs to fall and pinch the saw.
PRUNING
WARNING:
shoulder height or below.
branches are higher than your shoulder. Get
a professional to do the job.
S
Cut
S
Cut
WARNING:
plug before performing maintenance except
for carburetor adjustments.
We recommend all service and adjustments
not listed in this manual be performed by an
authorized or Master Service Dealer.
MAINTENANCE SCHEDULE
Check:
Fuel mixture level
Bar lubrication
Chain tension
Chain sharpness
For damaged parts
For loose caps
For loose fasteners
For loose parts
Inspect and Clean:
Bar
Complete saw
Air filter
Chain brake
Spark arresting screen
and muffler
Replace spark plug
Replace fuel filter
* Hours of Operation
AIR FILTER
CAUTION
or other flammable solvent to avoid creating
a fire hazard or producing harmful evapora-
tive emissions.
Cleaning the air filter:
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after 15
tanks of fuel or 5 hours of operation, which-
ever comes first. Clean more frequently in
13
Limit pruning to limbs
Do not cut if
Make your first cut
of the way
1/3
through the bottom of the limb.
Next make a 2nd cut all the way
through the limb. Then cut a third
overcut leaving a 1 to 2 inch collar
from the truck of the tree.
Second cut
Third cut
Collar
First cut
Pruning technique
SERVICE
Disconnect the spark
. . . .
Before each use
. . . . . . .
Before each use
. . . . . . .
Before each use
. . . .
Before each use
. .
Before each use
. . . . . .
Before each use
. . .
Before each use
. . . . . .
Before each use
. . . . . . . . . . . . . . . .
Before each use
. . . . . . .
After each use
. . . . . . . . . . . . .
Every 5 hours*
. . . . . . . .
Every 5 hours*
. . . . . . . . .
Every 25 hours*
.
Yearly
. . .
Yearly
: Do not clean filter in gasoline
Advertisement
Table of Contents
