Delta Jig Saw Instruction Manual
  1. Manuals
  2. Brands
  3. Delta Manuals
  4. Tools
  5. Jig Saw
  6. Instruction manual

Delta Jig Saw Instruction Manual

Tenoning jig
Hide thumbs
Table of Contents

Advertisement

Quick Links

Tenoning Jig
(Model 34-183)
PART NO. 1342471 - 02-02-05
Copyright © 2005 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
1-800-223-7278 (
1-800-463-3582).
please call
In Canada call

Advertisement

Table of Contents
loading

Related Manuals for Delta Jig Saw

Summary of Contents for Delta Jig Saw

  • Page 1 Tenoning Jig (Model 34-183) PART NO. 1342471 - 02-02-05 Copyright © 2005 Delta Machinery To learn more about DELTA MACHINERY visit our website at: www.deltamachinery.com. For Parts, Service, Warranty or other Assistance, 1-800-223-7278 ( 1-800-463-3582). please call In Canada call...

  • Page 2: Table Of Contents

    IMPORTANT SAFETY INSTRUCTIONS ............2 SAFETY GUIDELINES .

  • Page 3: Safety Guidelines

    16. USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by Porter-Cable may cause hazards or risk of injury to persons. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in “OFF” position before plugging in power cord.

  • Page 4: Additional Specific Safety Rules

    3. KEEP BOTH HANDS on the operating handles when operating the jig. 4. REPLACE THE BLADE GUARD OF THE SAW when the jig operation is complete. 5. REFER TO THE OWNER’S MANUAL of the saw for safety rules and other instructions. FUNCTIONAL DESCRIPTION FOREWORD Your new 34-183 Tenoning Jig will help you produce good, strong joints.

  • Page 5: Assembly

    If your saw is a right-tilt saw, follow the instructions for “ALIGNING TENONING JIG”. If your saw is a left-tilt saw, relocate the guide bar (G) Fig. 4 on the base (H) of the tenoning jig by using the following directions.
  • Page 6 Also, a T-slot washer (B) is on each end of the guide bar (A) to keep the tenoning jig from lifting during operation. NOTE: Remove the T-slot washers (B) if your table saw is not equipped with T-slotted miter gauge slots. Fig. 7 Fig.
  • Page 7 Place the tenoning jig guide bar (A) Fig. 12 into the left miter gauge slot. Use a square (E) Fig. 12 to see if the vertical work support plate (F) is 90 degrees to the saw table. If an adjustment is necessary, loosen the lock handle (G) and the set screw (H) Fig.

  • Page 8: Operation

    ADJUSTMENTS Disconnect Machine from Power Source 1. For rapid adjustment of the work support plate (A) Fig. 19, toward or away from the saw blade, loosen levers (B) and (C) and move jig (D). Tighten levers (B) and (C). 2. You can fine-adjust the work support plate (A) Fig. 19, by loosening the lever (B) and rotating the knob (E) until plate (A) is at the desired position.
  • Page 9 The tenoning jig features a positive stop to ensure fast and accurate positioning of the backstop (G) Fig. 21 at 90 degrees to the saw table. To check and adjust the positive stop at 90 degrees, loosen lock handle (H) Fig.
  • Page 10 Use a base stop (F) Fig. 28 that is the same thickness as the base plate (G) of the tenoning jig (H) and spacer block (K) that is the combined thickness of the tenon and the saw blade, to make the cutting more efficient.
  • Page 11 2. Lay the workpiece (L) Fig. 32 on the saw table and adjust the saw blade (R) to cut the structural shoulders of the tenon. Clamp a wooden stop block (S) Fig. 33 to the front of the saw fence (T), and adjust the saw fence to cut the structural shoulders of the tenon.
  • Page 12 Turn the machine “ON” and perform the structural shoulder cut by slowly pushing the miter gauge (W) Fig. 34 toward the saw blade until the saw blade is completely through the workpiece. Turn the machine “OFF”. Wait for the blade to come to a complete stop and remove the cut-off piece.
  • Page 13 TENON STUB TENON CONCEALED HAUNCHED TENON BARE FACED TENON RABBET TENON WITH LONG AND SHORT SHOULDERS SPLINE SPLINE GROOVE (SINGLE SAW CUT) MORTISE AND TENON WITH SPLINES MITERED TENON TENON ENDS MITERED SHOULDER OF CHEEK OF TENON MORTISE TENON SIMPLE MORTISE...

  • Page 14: Troubleshooting

    All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network • of Porter-Cable Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).

  • Page 15: Accessories

    A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our Web Site for the name of your nearest supplier. Since accessories other than those offered by Delta have not been tested with this product, use of such accessories could be hazardous.
  • Page 16 Phone: (604) 420-0102 Fax: (604) 420-3522 The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set Contractor’s Saw II™, Delta ®...

This manual is also suitable for:

34-183

Table of Contents