Related Manuals for Graco Pack ‘n Play Playard with Quick Connect Portable Napper Deluxe
Summary of Contents for Graco Pack ‘n Play Playard with Quick Connect Portable Napper Deluxe
- Page 1 Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE. See back page for quick set up guide. Pack ‘n Play Playard ® Quick Connect™ Portable Napper Deluxe ©2016 PD349520B 12/16...
-
Page 2: Table Of Contents
3-10 1 WARNING Pages 2 Features Pages 2-A Parts List 3 Assembly 12-18 Pages 3-A Set Up 3-B Bassinet 19-22 4 Use Pages 4-A To Fold 4-B To Cover 23-39 5 Accessories Pages 5-A Parent Organizer 5-B Changing Table 5-C Portable Napper Deluxe 6 Care 40-46 Pages... -
Page 3: Warning
Failure to follow these warnings and the instructions could result in serious injury or death. Setting Up the Playard Using the playard • THIS PRODUCT REQUIRES • The playard is for playing or ADULT ASSEMBLY. sleeping. When used for playing, never leave child unattended and •... - Page 4 NEVER add a mattress, pillow, over the playard. comforter or padding. Use ONLY • NEVER place items with a mattress pad provided by Graco. string around a child’s Mattress dimension: 27”x 36” neck, such as hood strings, (68.5 cm x 91.4 cm).
- Page 5 FOR SAFE BATTERY USE: Keep the batteries out of children’s reach. Any battery may leak battery acid if mixed with a different battery type, if inserted incorrectly (put in backwards) or if all batteries are not replaced or recharged at the same time. Do not mix old and new batteries.
- Page 6 Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 7 Parts list This model may not include some features shown below. Check that you have all the parts for this model BEFORE assembling your product. If any parts are missing, call Customer Service. Tools required: Flathead Screwdriver ALL MODELS...
- Page 8 3-A Set Up 1. Disconnect straps holding mattress around playard. 2. Remove mattress from around playard. 3. Pull up on side rails in middle above push button until all four sides are locked. DO NOT push center down yet. SNAP!
- Page 9 4. When setting up, lock rails BEFORE lowering center. SNAP! Be sure top rails have become rigid. If not, pull up again until they are rigid. If top rails do not latch, lift the center of the floor higher. 5. Hold one end of the unit up and push the center of the floor down.
- Page 10 7. Put two tabs under mattress/ pad through button holes and fasten securely on bottom of unit. 8. Pull strap through bottom of SNAP! playard and wrap around tube and refasten snap. Repeat on other corners. 9. Tuck four corners of mattress/ pad under corner stiffeners.
- Page 11 • If a sheet is used with the pad use only the one provided by Graco or one specifically designed to fit the dimensions of the bassinet.
- Page 12 1. Release snap straps and hook and loop straps on bottom of playard. Pull mattress fully out of playard. 2. Attach 4 bassinet mounts in the four corners and 2 clips over buttons on the long sides.
- Page 13 3. Insert tapered end of tube into end of other tube with hole in it. Repeat with other set of tubes. CHECK: Tubes MUST be assembled before placing mattress/pad in bassinet. 4. Insert the mattress/pad soft side up into the playard, making sure the hook and loop patches on bottom of mattress attaches to matching hook and loop patches...
- Page 14 4-A To Fold 1. Release snap straps and hook and loop straps on bottom of playard. Pull mattress fully out of playard. 2. DO NOT unlock top rails yet. Center of floor must be at least halfway up before top rails will unlock.
- Page 15 3. Center of floor must be up. a. Lift up slightly on the top rail. b. Push in on the button located on the side of the top rail to release the two tubes. c. Push down. • If top rails do not unlatch, do not force.
- Page 16 4. DO NOT FORCE. If unit will not fold, look for a partially latched top rail. Squeeze the latch button to release the rail. 5. Wrap mattress around play yard.
- Page 17 4-B To Cover 1. Cover unit with handle out. 2. Zip together.
- Page 18 5-A Parent Organizer WARNING Always keep objects out of child’s reach. Remove this accessory when child is able to pull himself up in the playard. 1. Insert hooks into openings in parent organizer. 2. Attach to end of playard.
- Page 19 • Always stay within arm’s reach of your child when using the changing table. Never leave child unattended. • The changing table is designed for use only with this Graco playard. Do not use on the floor, bed, counter or other surfaces.
- Page 20 1. Flip changer pad over so changer fabric is facing down. Slide tube through fabric as shown. 2. Repeat with other tube.
- Page 21 3. Tubes should appear exactly as shown. 4. Insert tubes into openings on plastic housing at end of changer. CHECK that button is visible in hole. SNAP! SNAP! 5. Repeat on other end of changer. CHECK that button is visible in hole.
- Page 22 6. Insert 3 tabs on both ends of changer into slots in plastic Underside of changer housing at ends of changer.
- Page 23 7. To attach changer to playard, line up lock logo on sides of changer with lock logo in one of the two attachment positions. Push changer onto playard rails. NOTE: Bassinet must be attached to playard when using changer. SNAP! Lock Logo 8.
- Page 24 5-C Portable Napper Deluxe WARNING Prevent serious injury or death: Failure to follow these warnings and the instructions could result in serious injury or death. FALL HAZARD: • To prevent falls, stop using the product when infant: • Begins to wiggle out of position or turn over in the product or •...
- Page 25 • To avoid suffocation, never use product inside bassinet unless it’s attached to the mounts on the playard frame in the identified locations. Never place product in the bottom of playard. • Always make sure product is securely attached to identified locations. •...
- Page 26 WARNING • To prevent serious injury or death, DO NOT REMOVE FOAM. Foot end (vibration switch) Head end (no switch) Extremo de la cabeza (sin interruptor) 1. Flip portable napper seat pad over so harness is facing down. 2. Insert the head support strap through the slot in the napper.
- Page 27 4. Using key or flat head Foot end screwdriver to open battery (vibration switch) compartment on back of napper leg with switch and insert 1-D (LR20-1.5V) (not included). Replace battery compartment door. 5. Attach portable napper legs attached to foot end by inserting end of one tube into opening as shown.
- Page 28 6. Attach other end of tube Head end asembled to foot end into head (no switch) end napper legs. CHECK: Buttons should be inserted and visible in openings. SNAP!
- Page 29 7. Insert ends of other tube into openings in napper legs. CHECK: Buttons should be inserted and visible in openings. SNAP! SNAP! 8. CHECK that 4 snaps on ends of channels are secured. SNAP! SNAP! SNAP! SNAP!
- Page 30 9. Attach the canopy mounts to the sides as shown. SNAP! SNAP! 10. To attach portable napper to playard, line up lock logo on sides of napper with lock logo in one of the two attachment positions. Push napper onto playard rails.
- Page 31 To Secure Child Use slide adjuster at waist for tighter adjustment. To Use Electronic Switch To use integrated electronic switch, slide button to left for low speed or right for high speed vibration.
- Page 32 To Remove Seat 1. To remove, press buttons on both sides of the seat handles and pull up as shown. 2. Pull up as shown.
-
Page 33: Care
6-A Care and Maintenance To Remove Seat Pad 1. Unfasten 4 snaps on ends of SNAP! SNAP! channels. SNAP! SNAP! 2. Press button on inside of leg housing tunnel and pull tube out of housing. Repeat on other ends of tubes. - Page 34 3. Remove tubes from seat pad. 4. Insert end of webbing through opening in leg housing to remove housing. Reverse steps to re-attach.
- Page 35 FROM TIME TO TIME CHECK YOUR PLAYARD for worn parts, torn material or stitching. Replace or repair the parts as needed. Use only Graco® replacement parts. IF PLAYARD IS USED AT THE BEACH, you MUST clean sand off your playard, including the feet, before packing it into cover. Sand in top rail lock may damage it.
- Page 36 Quick Fold Guide 1. Pull red tab up to unlock. Center of floor must be at least halfway up before top rails will unlock. (See page 19) Lift rail up slightly, press button and lower rail. Repeat on all 4 sides. (See page 20) 3.
- Page 37 Quick Set Up Guide SNAP! SNAP! SNAP! SNAP! 1. Pull up on all 4 sides and snap into place. Do not push center of Playard down until top rails are locked. (See pages 12 and 13) 2. Push center of playard down until you hear a click.